dji FlameWheel330 F330 User manual

FlameWheel330
User Manual
V 1.1
www.dji-innovations.com

Disclaimer
Read this disclaimer carefully before using FlameWheel330. By using this product, you hereby agree to
this disclaimer and signify that you have read them fully. FlameWheel330 is an excellent multi-rotor. With
a good autopilot, it will even offer tremendous flight features for low altitude flight working in restricted
space. Despite the controller of autopilot operate in the safest manner when the main power battery is
connected, we strongly recommend customers to remove all propellers, use power supply from R/C
system or flight pack battery, and keep children away during system calibration and parameter setup.
Dajiang Innovation Technology Co. Ltd. assumes no liability for damage(s) or injuries incurred directly or
indirectly from the use of this product.
F330 Profile
FlameWheel330 (F330) is a multi-rotor designed for all pilots for fun or AP. With DJI Naza autopilot
system, it can achieve hovering, cruising, even rolling and other flight elements. It can be applied for
entertainment, aerial photography, FPV and other aero-modeling activities.

Contents
Disclaimer.......................................................................................................................2
F330 Profile....................................................................................................................2
Contents.........................................................................................................................3
Product Usage Cautions.................................................................................................3
In Box.............................................................................................................................4
Tools Needed .................................................................................................................5
Specifications.................................................................................................................7
ESC Wiring.....................................................................................................................5
Assembly........................................................................................................................6
Product Usage Cautions
When flying, the fast rotating propellers of FlameWheel330 will cause serious damage and injury.
Therefore, please fly with a high safety consciousness.
1. Keep flying multi-rotor away from objects, such as obstacles, human beings, high-voltage
lines and so on.
2. Do not get close to or even touch the working motors and propellers, which will cause
serious injury.
3. Do not over load the multi-rotor.
4. Check whether the propellers and the motors are installed correctly and firmly before flight.
5. Make sure the rotation direction of each propeller is correct
6. Check whether all parts of multi-rotor are in good condition before flight. Do not fly with old
or broken parts.
7. Use DJI parts as much as possible.
If you have any problem you cannot solve during installation, please contact our customer
service.

In Box
Top Board 330FBT ×1
Bottom Board 330FBB ×1
Arms 330FAW ×2 330FAC ×2
8in Propeller Pairs 330P08×2
Motors 330MOT ×4
ESC 330ESC ×4
18A
OPTO
+
-
U
V
W
Screws 330-M3×8 ×16
Screws 330-M2.5×5 ×20
Magic Strap 330MSX ×1, Battery Band 330BBX ×1

Tools Needed
2.0mm Hex Wrench
For frame and motors installation.
Screw Glue
For fastening screws.
Nylon Cable Tie
For binding devices and wires.
Scissors
Diagonal Cutting Pliers
Foam Double Sided Adhesive Tape
For fixing receiver, controller and other modules.
Soldering-iron & wires
For connecting ESCs’power cables to bottom board.
ESC Wiring
ESC
ESC
ESC
电调
To Battery
· Please solder ESCs to power pads on bottom board as the figure shows.
· Use any insulating method at all soldering spots. Make sure there is no short or open circuit.
· Make sure the side of power pads is upward.
Power Pads

Assembly
Step 1
Install bottom board
Step 2
Install autopilot system
Step 3
Install motors, ESCs
Step 4
Install top board
Step 5
Install propellers
Install screws by appropriate force to
prevent breaking threads. Use adequate
screw glue for installing screws.
Please wire neatly. Make sure wires will not
be cut by frame boards and propellers.
Smooth out the boards edge if necessary
Please i ns ta ll propellers after a ut opilot s ys te m
configuration procedure. Make sure the rotation
direction of propellers are the same as the figure shows
In up figure, arms ①② front of craft, arms ③④ are back of craft. You'd better choose the same color arms for the same direction. See from top, motors
on arms ①③ rotate counter-clock wise, use propellers 8045; motors on arms ②④ rotate clock wise, use propellers 8045R.
①
②
③ ④
Top
Board
Bottom
Board
Screws
M2.5×5
Screws
M3×8
Arm
Motor Motor
Arm
Make sure use the washers to
install motors as the figure
shows, otherwise the screw will
touch the motor coil.

ESC Sound Introduction
ESC State
Sound
Ready
♪1234567
Throttle stick is not at bottom
BBBBBB…
Input signal abnormal
B---------B---------B…
Input voltage abnormal
BB----BB----BB----BB….
Tips:
DJI ESCs are specially designed for multi-rotors. When use with DJI autopilot systems, you do not
have to setup any parameters or calibrate travel range.
Specifications
Frame
Diagonal Wheelbase
330mm
Frame Weight
156g
Takeoff Weight
600g ~ 1200g
ESC
Current
18A OPTO
Signal Frequency
30Hz ~ 450Hz
Battery
3S ~ 4S LiPo
Motor
Stator size
22×12mm
KV
920rpm/V
Propeller
8 ×4.5in

FlameWheel 330
©2010-2011 Dajiang Innovation Technology Co. Ltd. All Rights Reserved.
6/F, HKUST SZ IER Building, No.9, Yuexing 1st Rd.,
South District, Hi-Tech Park, Shenzhen, 518057, Guangdong, China
Tel: [phone] Sales ext 201, 202, 203
Fax: [phone] Service hotline:[phone]
Sales:[e-mail] Technical support: [e-mail]
Others:[e-mail]
DJI FLAME WHEEL is registered trademark of Dajiang Innovation Technology Co. Ltd. Names of product, brand, etc.,
appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and
manual are copyrighted by Dajiang Innovation Technology Co. Ltd. with all rights reserved. No part of this product or
manual shall be reproduced in any form without the prior written consent or authorization of Dajiang Innovation
Technology Co. Ltd. No patent liability is assumed with respect to the use of the product or information contained herein.