DMP Electronics 86Duino ENJOY Instruction manual
www.86duino.com
2016.Jan Ver. 1.0
Content
ENJOY Introduction (p. 2)
Software Installation* (p. 3)
Install print S/W (p. 4)
Driver Install (p.10)
Hardware (p.13)
Hardware Intro. (p.14)
Cable installation (p.15)
Power and Trans cable
install
(p. 20)
Calibration settings(p. 22)
Setup and connection(p. 23)
Extruder Calibration (p. 30)
Print bed Calebration (p. 40)
Print test (p.43)
Load 3D object (p.44)
Adjust print object(p. 46)
Slice and G-Code(p. 48)
Start print (p. 51)
Appendex (p.54)
1
*This installation instruction base on Microsoft Windows 7
86Duno ENJOY outline
2
Front view Rear view
Gearbox
Feeding Tube
Rear Panel
Extruder
Print Bed
LED Panel
X、Y Stepper
Motor
Z screw
Bed adjust
knob
Unload button
Software Installation
3
S/W-Print software install (2/6)
1.
2.
Click “Next” on Setup Wizard : Read the License Agreement and if in
agreement, Select “I accept the agreement”
and then click “Next” .
3.
5
S/W-Print software install (3/6)
4.
Click “Next” if you like to put it under “Program
Files” or you can choose your preferred location
by clicking “Browse…”
then click “Next”（default setting）
5.
6
S/W-Print software install (4/6)
6.
Click “Next” if you like to put the shortcut in
“86Duino Repetier-Host” folder or you can click
“Browse…” to choose a different folder.
If you would like to create a desktop icon, check off,
“Create a desktop icon” and then click “Next”.
7.
8.
7
9.
Click “Install” to start the installation. Software Installation
8
S/W-Print software install (5/6)
After installation is complete, you
can choose whether to continue to
install the driver.
If the previous driver has been
installed, you can skip the "Driver
Installation" teaching content.
If you do not execute software now
and then, can be performed by
clicking "RepetierHost.exe" file.
Installation completion
12.
10. Install
serial driver
11. Lanch 86Duino
Repetier-Host
86Duino Repetier-
Host Icon 9
S/W-Print software install (6/6)
If you choose to print software installation to continue after the completion of driver
installation, the following installation screen will appear, please follow the instructions
to complete the installation:
S/W-Driver install(1/3)
Driver extract confirmation screen Driver extracting screen
1.
10
2.
Read the LicenseAgreement and if in agreement,
Select “I accept the agreement” and then click “Next” .
11
Click “Next” for Setup Wizard :
4.
3.
S/W-Driver install(2/3)
Installation completion screen
12
Install screen
5.
S/W-Driver install (3/3)
Hardware assembly
13
ENJOY includes the following items at the box:
Hardware description
Accessories
14
ENJOY Printer
5.
3.
1. Power Adapter
3. micro USB
cable
6Extruderpositioned tested
2. Test print
5. Printing board（include Clips)
4. Filament holder
Mounted filament holder on the rear of the printer:
H/W-Loading Filament (1/5)
15
1. Counterclockwise direction of the mounting holder
ENJOY rear view
Filament holder
mounting holes
2. Place the Filament
hanging on the holder
(note direction)
Direction
Holder
16
Prior to each use, remove the harden/used end of the filament
by cutting off 2 inch from the end to be loaded into the extruder.
Feeder
4. feed the filament
into the Feeder
Thread
3. Cutting
ENJOY rear
H/W-Loading Filament (2/5)
17
Push up on the spring to the left while feeding the
filament up into the tube.
Feeder Feeder
5. Push up on the spring 6. gears will be moved to the
right, to generate the space
ENJOY rear
H/W-Loading Filament (3/5)
18
Continue to feed the filament up into the extruder until
you feel there is NO room for more filament.
Feeder Feeder
7. Feed the filament up into
the feeder 8. until you feel there is NO
room for more filament.
ENJOY rear
H/W-Loading Filament (4/5)
Table of contents
