DMP Electronics 1128INT User manual

1128INT WIRELESS GLASSBREAK DETECTOR
Installation Guide
GET STARTED
Figure 1: 1128INT Glassbreak Detector
The 1128INT Wireless Glassbreak
Detector is a fully-supervised,
low current shock and glassbreak
sensor that provides detection
coverage up to 20 ft from framed
glass mounted in an outside wall.
The 1128INT features 128-bit AES
encryption.
You can mount the detector on
the ceiling or an opposing wall for
maximum flexibility and coverage.
The 1128INT operates using the
supplied 3.0 V lithium battery.
Compatibility
• 1100XINT Wireless Receivers
Version 700 and Higher
• 1100DINT Wireless Receivers
Version 700 and Higher
• XT30INT Series Panels Version
693 and Higher
• XTLtouchINT/XTLplusINT Series
Panels Version 693 and Higher
• XR150INT/XR550INT Series
Panels Version 693 and Higher
What is Included?
• One 1128INT Wireless
Glassbreak Detector
• One 3.0 V Lithium CR123A
Battery
• Hardware Pack
1PROGRAM THE PANEL
Refer to the panel programming guide as needed.
1. If using an XT Series International Panel, enter 665 (PRO) at
the keypad to access the PROGRAMMER menu. If using an
XR Series International Panel, enter 6653 (PROG).
2. Press CMD until ZONE INFORMATION displays and press a
top row select key or area.
3. Enter the wireless ZONE NO and press CMD.
4. Enter the ZONE NAME and press CMD.
5. Select NT (Night) as the ZONE TYPE.
6. Select the AREA NO and press CMD.
7. At NEXT ZN?, select NO and press CMD until WIRELESS?
displays.
8. Select YES when WIRELESS? displays and press CMD.
9. Enter the eight-digit SERIAL# and press CMD.
10. Enter the SUPRVSN TIME and press CMD.
11. At NEXT ZN?, select YES if you are finished programming
the zone. Select NO if you would like to access additional
programming options.
12. In SYSTEM OPTIONS, at the 1100 ENCRYPTION prompt,
select ALL to only add encrypted wireless devices to the
system. Select BOTH to allow both encrypted and non-
encrypted wireless devices to be programmed.
13. The default passphrase appears at ENTER PASSPHRASE.
Press CMD to keep the default. Press any select key or
area to change the passphrase and enter an 8-character
hexadecimal string (0-9, A-F).
Use a 3.0V lithium battery, DMP Model CR123A, or the equivalent
battery from Sony or Murata. When setting up a wireless system,
program zones and connect the receiver before installing batteries
in the transmitters.
1. Remove the holding screw at the lower end of the 1128INT
case and gently life o the cover. See Figure 2.
2. Observing polarity, place the battery in the holder. Press it
into place. See Figure 3 for the battery location.
INSTALL THE BATTERY
2
Figure 2: Open the 1128INT
LED
Holding
Screw
Figure 3: 1128INT Battery Location
Tamper
Battery
Holder

2 1128INT INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
SELECT A LOCATION
The 1128INT’s omni-directional detection
coverage is measured from 1128INT to the
point on the glass farthest from the 1128INT.
Refer to the table below to determine the
best location to place the 1128INT based on
window type, glass thickness, window to wall
range, and wall type.
Note: The sensor can be mounted as
close as 3.3’ (1 m) from the glass and the
minimum glass size is 1’ x 2’ (0.3 m x 0.6 m).
Optimize Detection
To optimize detection, install the 1128INT in the
following areas:
• Large rooms with moderate noise
• In the direct line of sight of all windows that are
to be protected
• On the opposite wall of the window that it’s
protecting (see Figure 4 for detection range)
Avoid False Alarms
To avoid false alarms, do not install the 1128INT in the following areas:
• Rooms with lined, insulated, or dampening drapes
• Rooms with closed, wooden shutters on the inside
• Room corners
• Where white noise (air compressor) is present
• Rooms smaller than 10’x 10’
• Rooms with multiple noise sources like televisions, sinks, speakers, etc.
• Excessively humid rooms
Note: Program the 1128INT as a night zone to help avoid false alarms.
Check the Location Using Survey LED
1. Hold the 1128INT in the exact desired location.
2. Press the tamper switch to send data to the receiver and determine if communication is confirmed or
faulty. See Figures 2 and 3 for tamper switch and LED locations.
Confirmed: If communication is confirmed, the survey LED turns on when data is sent to the wireless
receiver and o when acknowledgment is received.
Faulty: If communication is faulty, the LED remains on for several seconds or flashes multiple times
in quick succession. Relocate the 1128INT or the wireless receiver until the LED confirms clear
communication. Proper communication between the 1128INT and wireless receiver is verified when for
each press or release of the tamper switch, the LED blinks immediately on and immediately o.
3
4MOUNT THE 1128INT GLASSBREAK DETECTOR
1. With the 1128INT already open, place the 1128INT base on the wall in
the desired location.
2. Use the provided hardware pack to mount the base to the wall. See
Figure 5 for mounting hole locations.
3. Reinstall the 1128INT cover back on to the base and tighten the holding
screw.
Window Type Glass Thickness Maximum Range Wall Type
Plate 3/32" - 1/4" (2.4mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling
Tempered 1/8" - 1/4" (3.2mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling
Laminated 1/8" - 1/4" (3.2mm - 6.4mm) 20' (6m) Opposite, adjoining, ceiling
Wired 1/4" (6.4mm) 20' (6m) Opposite, adjoining, ceiling
Armor-coated N/A 12' (3.65m) Opposite, adjoining, ceiling
20 ft (6m)
20 ft (6m)
Figure 4: 1128INT Detection Range
MOUNTING HOLES
Figure 5: Mounting Holes

1128INT INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3
5TEST THE 1128INT GLASSBREAK DETECTOR
Handheld Glassbreak Test
To test the 1128INT, use a handheld tester like the FG-701 to imitate glass breaking. For more information, refer
to the glassbreak tester manual.
1. Set the tester to flex mode.
2. Place the FG-701 near the protected glass and press the button to activate the simulator. It will not
annunciate the sound of shattering glass until a low-frequency shock is also generated.
3. To generate the shock, slam a framed door to generate the appropriate low-frequency shock. The
shock will also activate the FG-701 simulator,
Note: The 1128INT has two onboard microphones. Both the high frequency and low frequency
microphones must be activated to send an alarm to the control panel. If only the low frequency
microphone activates, the LED on the 1128INT will flash green. When both activate, the LED will flash red
and the 1128INT will transmit an alarm to the control panel.
Wireless Check-in Test
After the transmitter has been installed, test to confirm that it is communicating reliably with the panel. Use
the Tech APP™ to perform a Wireless Check-in Test on the system or complete the following steps to perform
a Check-in Test from a keypad that is connected to the panel.
1. At the keypad for XT Series panels, enter 8144 (WALK). At the keypad for XR Series panels, enter 814
(WAL).
2. Select WLS.
3. If the 1128INT fails to check in at the keypad, relocate the wireless device, receiver, or panel.
Glassbreak Check-in Test (v7.0.0.2 and higher)
When the 1128INT is set into testing mode from the panel, it will trip using the tester only. There is no need to
generate shock trip to the detector. XTINT and XRINT Series firmware Version 191 is required to perform the
glassbreak walk test.
1. Reset the panel.
2. If using an XT Series International Panel, enter 8144 (WALK). If using an XR Series International Panel,
enter 814 (WAL).
3. Select PIR. All 1128INTs on the system will begin flashing a green LED every 3 seconds to indicate that
they are in testing mode. It can take up to 3 minutes for all 1128INTs to enter testing mode
Note: The PIR option will enable testing of all supported wireless PIRs and 1128INTs on the system.
4. Set the tester to manual mode.
5. Place the FG-701 near the protected glass and press the button to activate the simulator. If the 1128INT
is in range, it will flash the LED red for 3 seconds to indicate it detected the crash.
6. The 1128INT will remain in testing mode for 30 minutes or until the panel is reset.
ADDITIONAL INFORMATION
Replace the Battery
1. Remove the holding screw at the lower end of the 1128INT and gently lift o the cover.
2. Remove the old battery and dispose of it properly.
3. Observing polarity, place the new battery in the holder and press into place.
Note: Use only 3.0 V lithium CR123A batteries.
4. Place the cover back onto the 1128INT and tighten the holding screw back into place.
Sensor Reset to Clear LOBAT
When the battery needs to be replaced, a LOBAT message will display on the keypad. Once the battery is replaced, a
sensor reset is required at the system keypad to clear the LOBAT message.
1. On a Thinline keypad, press and hold “2” for two seconds. On a touchscreen keypad press RESET.
2. Enter your user code if required.
3. The keypad displays SENSORS OFF followed by SENSORS ON.

Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-1825INT 1.01 22133
1128INT
GLASSBREAK
DETECTOR
Specifications
Battery
Life Expectancy 3 years (normal operation)
Type 3 V lithium CR123A
Frequency Range 863-869 MHz
Transmit Condition Alarm, Low Battery, Tamper
Detection Method Omnidirectional
Range 20 ft (6 m)
Operating Temperature -10°C to 55°C
Color White (passes VW1)
Housing Material Flame retardant ABS
Dimensions 3.3”L x 2.1”W x 0.9”D
Weight 4.2 oz
Accessories
FG-701 Glassbreak Simulator
Patents
U. S. Patent No. 7,239,236
International Certificates
Intertek (ETL)
EN 60950-1: 2006+A11(09)+A1(10)+A12(11)+A2(1)
Information technology equipment -
Safety - Part 1: General
Requirements
IEC 60950-1:2005 (2nd Edition)+Am 1:2009+Am 2:2013
Information technology equipment -
Safety - Part 1: General
Requirements
EN 50130-4: 2011 Alarm systems - Part 4:
Electromagnetic compatibility
- Product family standard: Immunity
requirements for components of
fire, intruder, hold up, CCTV, access
control and social alarm systems
EN 301 489-1 V1.9.2 Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Electromagnetic Compatibility
(EMC) standard for radio equipment
and services; Part 1: Common
technical requirements
EN 301 489-6 V1.3.1 Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Electromagnetic Compatibility
(EMC) standard for radio equipment
and services; Part 6: Specific
conditions for Digital Enhanced
Cordless Telecommunications
(DECT) equipment
EN 6100-6-1:2007 Electromagnetic compatibility
(EMC) - Part 6-1: Generic standards
- Immunity for residential,
commercial, and light-industrial
environments
EN 6100-6-3:2007/A1:2011 Electromagnetic compatibility
(EMC). Generic standards. Emission
Standard For Residential,
Commercial And Light-Industrial
Environments
EN 301 406 V2.1.1 Digital Enhanced Cordless
Telecommunications
(DECT); Harmonized EN for Digital
Enhanced Cordless
Telecommunications (DECT)
covering the essential requirements
under article 3.2 of the R&TTE
Directive; Generic radio
EN 50581:2012 Technical documentation for the
assessment of electrical and
electronic products with respect to
the restriction of hazardous
substances
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
417.8311.9362 | DMP.com
© 2022