DMP Electronics XTLplusINT Series Installation guide

DIGITAL MONITORING PRODUCTS, INC.
INTERNATIONAL PROGRAMMING GUIDE

MODEL XTLplusINT SERIES
INSTALLATION AND PROGRAMMING GUIDE
If necessary, the installer should consult the dealer or an experienced radio/television technician
for additional suggestions. The installer may find the following booklet, prepared by the Federal
Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Oce, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2022 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
i
PANEL SPECIFICATIONS
Power Supply........... ........................................................1
Communication...............................................................1
Keypads ...................................................................1
Number of Zones ...........................................................1
Enclosure Specifications .............................................1
INTRODUCTION
System Configurations................................................. 2
Caution Notes.................................................................. 2
Compliance Instructions.............................................. 2
SYSTEM COMPONENTS
Accessory Devices....................................................... 3
INSTALLATION
Mounting Location Information.............................. 4
Mounting the Enclosure............................................. 4
PRIMARY POWER SUPPLY
DC Input........................................................................... 4
SECONDARY POWER SUPPLY
Standby Battery............................................................ 5
Replacement ................................................................. 5
Battery Supervision..................................................... 5
LED OPERATION
Backlit Logo ................................................................. 6
RESET BUTTON
Description....... .............................................................. 6
TAMPER BUTTON
Description........ ............................................................. 6
PROG PROGRAMMING CONNECTION
Description........ ............................................................. 6
ON-BOARD 1100INT SERIES WIRELESS
Wireless Antenna ......................................................... 6
Wireless LED Operation ............................................ 6
WIRELESS ZONES
Description........ ............................................................. 6
WIRELESS KEY FOBS AND OUTPUTS
Description........ ..............................................................7
FLASH LOAD BUTTON
Description....... ...............................................................7
ON-BOARD Z-WAVE CONNECTION
Description....... ...............................................................7
ON-BOARD WI-FI NETWORK
Description....... ...............................................................7
CELLULAR CONNECTION
Description....... .............................................................. 8
WIRELESS KEYPADS
Mounting Wireless Keypads..................................... 8
Wi-Fi LEDs....... ............................................................... 8
PROGRAMMING INTRODUCTION
Before You Begin ......................................................... 8
Getting Started ............................................................. 9
Keypad.......................... ................................................... 11
Special Keys........ ........................................................... 11
Entering Characters Using the Number Pad .... 12
Entering Characters Using the Standard
Keyboard (Graphic Touchscreen Keypads) ...... 12

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
ii
Keypad Displays Current Programming............. 12
Programming Menu....................................................13
Programmer Lockout Codes................................... 13
Reset Timeout ..............................................................13
INITIALIZATION
Initialization...... .............................................................14
Clear All Codes.............................................................14
Clear All Schedules.....................................................14
Clear Events...... ............................................................14
Clear Zone Programming.........................................14
Clear Communication................................................14
Clear Wi-Fi.....................................................................14
Set to Factory Defaults.............................................14
FAST PROGRAMMING
Fast Program.... ............................................................15
Account Number .........................................................15
First IP Address............................................................15
App Key...........................................................................15
System.............................................................................15
Hours from GMT ..........................................................15
Weather Postal Code.................................................15
Enter Siren Serial Number ....................................... 15
Zone Number... .............................................................15
Zone Name........ ............................................................15
Zone Type.......... ............................................................15
Area Assignment.........................................................15
Serial Number Entry................................................... 15
Stop..................... .............................................................15
COMMUNICATION
Communication............................................................16
Account Number .........................................................16
Transmission Delay .....................................................16
Communication Type.................................................16
Backup Cellular ............................................................16
Test Time.........................................................................16
Test Days............ ............................................................16
Check-In Minutes.........................................................16
Fail Time..........................................................................16
Send Communication Trouble................................ 17
First Cell APN... ............................................................ 17
Receiver 1 Programming........................................... 17
Alarm Reports. ............................................................. 17
Supervisory/Trouble Reports ................................. 17
Opening/Closing and User Reports..................... 17
Test Report....... ............................................................. 17
First IP Address............................................................ 17
First IP Port.................................................................... 17
Second IP Address...................................................... 17
Second IP Port.............................................................. 17
Receiver 2 Programming.......................................... 17
Receiver 2 Backup? ....................................................18
Alarm Reports. .............................................................18
Supervisory/Trouble Reports .................................18
Opening/Closing and User Reports.....................18
Test Report....... .............................................................18
First IP Address............................................................18
First IP Port....................................................................18
Second IP Address......................................................18
Second IP Port..............................................................18

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
iii
NETWORK OPTIONS
Network Options.........................................................19
Wi-Fi Setup....................................................................19
WPS..................................................................................19
List.....................................................................................19
Manual.................. ...........................................................19
Test...................................................................................20
Wireless Security Type.............................................20
Wireless Network Key ..............................................20
DHCP................... ............................................................20
Local IP Address.........................................................20
Gateway Address .......................................................20
Subnet Mask.................................................................20
DNS Server....................................................................20
Programming Port .....................................................20
DEVICE SETUP
Device Setup................................................................. 21
Device Number ............................................................ 21
Device Name................................................................. 21
Door Device Type........................................................ 21
Network............. ............................................................. 21
Wireless........................................................................... 21
Serial Number.. ............................................................. 21
Supervision Time......................................................... 21
REMOTE OPTIONS
Remote Options.......................................................... 22
Remote Key....... ........................................................... 22
Remote Disarm ........................................................... 22
App Key (For EASYconnect only) ....................... 22
SYSTEM REPORTS
System Reports...........................................................23
Opening/Closing Reports....................................... 23
Abort Reports..............................................................23
Zone Restoral Reports .............................................23
Bypass Reports...........................................................23
Code Change Reports.............................................. 23
Send Stored Messages.............................................23
Ambush.......................................................................... 23
Late To Open................................................................23
Early To Close.. ............................................................23
Entry Check-in Protection ......................................24
SYSTEM OPTIONS
System Options...........................................................25
System............................................................................ 25
Closing Code................................................................ 25
Closing Check.............................................................. 25
Entry Delay........ ........................................................... 25
Exit Delay.......................................................................25
Cross Zone Time......................................................... 25
Power Fail Delay .........................................................26
Swinger Bypass Trips................................................26
Reset Swinger Bypass..............................................26
Zone Activity Hours ..................................................26
Arm Activity Days......................................................26
Time Zone Changes ..................................................26
Time Display..... ............................................................ 27
House Code...... ............................................................ 27
Detect Wireless Jamming....................................... 27
Trouble Audible Annunciation .............................. 27
Enable Keypad Panic Keys ..................................... 27

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
iv
Wireless Encryption .................................................. 27
Enter Passphrase........................................................ 27
Occupied Premises....................................................28
Use False Alarm Question ......................................28
Weather Postal Code................................................28
BELL OPTIONS
Bell Options..................................................................29
Bell Cuto Time..........................................................29
Automatic Bell Test ...................................................29
Bell Output........ ...........................................................29
Bell Action.....................................................................29
Fire....................... ............................................................29
Burglary..........................................................................29
Supervisory...................................................................29
Panic................................................................................29
Emergency........ ............................................................29
Auxiliary 1........... ...........................................................29
Auxiliary 2.......... ...........................................................29
Carbon Monoxide (CO)............................................29
OUTPUT OPTIONS
Output Options...........................................................30
Communication Failure Output............................30
Fire Alarm Output......................................................30
Fire Trouble Output...................................................30
Ambush Output ..........................................................30
Begin Exit Output ......................................................30
End Exit Output..........................................................30
Ready Output... ...........................................................30
Armed Output.. ...........................................................30
Disarmed Output........................................................30
Burglary Output..........................................................30
Arm-Alarm Output ....................................................30
Heat Saver Temperature...........................................31
Cool Saver Temperature...........................................31
Carbon Monoxide Alarm Output...........................31
Zone Monitor Output.................................................31
OUTPUT SETUP
Output Setup.... ...........................................................32
Output Number...........................................................32
Output Name... ............................................................32
Serial Number... ...........................................................32
Supervision Time........................................................ 32
Trip with Panel Bell Option.....................................32
AREA INFORMATION
Area Information ........................................................33
Area Number................................................................ 33
Area Name......... ...........................................................33
Automatic Arming .....................................................33
Bad Zones.......... ...........................................................33
Automatic Disarming................................................33
ZONE INFORMATION
Zone Information........................................................34
Zone Number.... ...........................................................34
Key Fob.......................................................................... 35
Zone Name......... ..........................................................35
Zone Type.......... ...........................................................35
Arming Zone Assignment....................................... 35
Area Assignment........................................................36
Style.................................................................................36

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
v
DMP Wireless...............................................................36
Serial Number Entry..................................................36
Contact...........................................................................36
Supervision Time........................................................ 37
LED Operation............................................................. 37
Disarm/Disable............................................................ 37
Wireless PIR Pulse Count........................................ 37
Wireless PIR Sensitivity ........................................... 37
Pet Immunity................................................................ 37
Next Zone...................................................................... 37
1144INT Series Key Fobs.......................................... 37
Key Fob User Number.............................................. 37
Key Fob Serial Number............................................ 37
Key Fob Supervision Time......................................38
Number of Key Fob Buttons..................................38
Key Fob Button Selection (Four Buttons)........38
Key Fob Button Selection (Two Buttons).........38
Button Action.. ............................................................38
Button Press Time......................................................38
Arm/Disarm Area Selection...................................39
Output Number...........................................................39
Output Action..............................................................39
Alarm Action................................................................39
Disarmed Open...........................................................39
Message To Transmit.................................................39
Output Number.......................................................... 40
Output Action............................................................. 40
Swinger Bypass.......................................................... 40
Prewarn Address ....................................................... 40
Chime............................................................................. 40
Entry Delay........ .......................................................... 40
Cross Zone.....................................................................41
Priority................ .............................................................41
Trac Count..................................................................41
Zone Audit Days..........................................................41
Receiver Routing.........................................................41
Zone Number... .............................................................41
STOP
Stop..................... ............................................................42
SET LOCKOUT CODE
Set Lockout Code ......................................................43
APPENDIX
Status List.......... ...........................................................44
Transmission Delay ....................................................44
False Alarm Reduction.............................................44
Diagnostics Function................................................45
Using the Walk Test...................................................47
Walk Test........... ............................................................47
Trip Counter For DMP Wireless Test (WLS) ....47
Test End Warning .......................................................47
Failed Zones Display.................................................47
Keypad Speaker Operation....................................47
Cross Zoning................................................................48
Zone Type Descriptions...........................................48
Zone Type Defaults ...................................................48
Common Keypad Messages...................................49
ALARM TRANSMISSION SYSTEMS AND
EQUIPMENT EN 50136-1 AND -2
SPECIFICATIONS
LISTED COMPLIANCE SPECIFICATIONS

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
1
PANEL SPECIFICATIONS
Power Supply
Model 372-500-W plug-in DC power supply
Input: 120 VAC, 60 Hz
Output: 12 VDC
Standby Battery: DMP 3.8 VDC Lithium, 800 mAh
Optional Standby Battery DMP 3.8 VDC Lithium, 3500 mAh
All circuits inherent power limited
Communication
Optional 265LTE-INT Series Cellular Communicator to send messages to DMP Model SCS-1R or SCS-VR Central
Station Receivers.
Built-in Wi-Fi network alarm signal communication to DMP Model SCS-1R or SCS-VR Central Station Receivers.
Keypads
You can associate up to seven 9862INT Series Graphic Touchscreen Keypads.
Number of Zones
• XTLplusINT has 99 wireless initiating zones numbered 1-99
• Zone and Output numbers 51 to 54 and 61 to 64 can support 1144INT Series Key Fobs, Output Modules,
or sirens
Enclosure Specifications
Size Color
5.5” W x 3.75” H x 1” D White (W)
31-34 Slow response time wireless outputs
(activates within 15 seconds)
41-44 Fast response time wireless outputs
(activates within 1 second)
F1 - F20 Used for Z-Wave favorites
XTLplusINT
Total Number of Zones 99
Number of Possible
Hardwired Zones
0
Number of Possible
Wireless Zones
99
Number of Areas 6
Event Buer 200
Number of User Codes 99
Number of Door Access
Points
0
Number of Supervised
Keypads
7

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
2
INTRODUCTION
System Configurations
The panel can be programmed to operate as any of the following system types:
• All/Perimeter system that provides one perimeter area and one interior area
• Home/Sleep/Away system that provides one perimeter, one interior, and one bedroom area. The bedroom
area provides for any protection devices the user wants disarmed during their sleeping hours and armed as
Away.
• Six area system that provides areas of protection that can be independently armed or disarmed.
Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the panel.
These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely read
and understand its information. Failing to follow the caution note can cause damage to the equipment or improper
operation of one or more components in the system.
Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certificated system, please see the Listed Compliance Specifications section near the end of this guide for
additional instructions.
SYSTEM COMPONENTS
ACCESSORY DEVICES
Cellular Communicator Cards
265LTE-INT Cellular Communicator Allows you to connect the XTLplusINT to an LTE network.
DMP Two-Way Wireless Devices
1100RINT Repeater Provides additional range for wireless devices
1103INT Universal Transmitter Provides both internal and external contacts that may be used at the same
time to yield two individual reporting zones from one wireless transmitter.
Requires EOL resistor for external contact. Provides Disarm/Disable
functionality.
1122INT PIR Motion Detector Provides motion detection with pet immunity.
1128INT Glassbreak Detector Provides fully superivsed, low-current shock glassbreak detection.
1135INT Siren Provides a wireless siren.
1142INT Two-button Panic Transmitter Provides permanently mounted under-the-counter two-button panic
operation.
1144-4INT (Four-Button)
1144-2INT (Two-Button)
1144-1INT (One-Button)
Key Fob transmitters designed to clip onto a key ring or lanyard.
Keypads
9862INT Wireless Graphic Touchscreen
Keypad
Allows you to control the panel from various remote locations.

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
3
INSTALLATION
Mounting Location Information
A location should be selected that is centrally located between the 1100INT Series transmitters used in the installation.
Install the XTLplusINT away from metal objects. Mounting the panel on or near metal surfaces impairs performance.
When selecting the proper mounting location of a transmitter, refer to the LED Survey Operation section of the
specific installation guide for the transmitter being installed.
Mounting the Enclosure
The enclosure for the panel must be mounted using the provided #6 screws in the four mounting holes shown in
Figure 1. Mount the enclosure in a secure, dry place away from metal objects to protect the panel from damage due to
tampering or the elements. Mount the panel a minimum of 4 feet from any wireless transmitters or repeaters. It is not
necessary to remove the PCB when installing the enclosure.
Primary Power Supply
DC Input
Mount the panel near a wall outlet for the Model 372-500-W plug-in DC power supply. In addition to powering the
panel, the DC plug-in power supply also charges the back-up battery. The 372-500-W must be located within 100 feet
of the panel using 22 AWG wire. Use the following steps to connect the plug-in power supply:
OBSERVE POLARITY
1. Using 22 AWG wire, connect the panel DC terminal (+) to the positive terminal on the power
supply.
2. Connect the panel DC terminal (-) to the negative terminal on the power supply. See Figure 2.
3. Plug the power supply into a 120 VAC, 50 Hz dedicated outlet not controlled by a switch.
RESETLOAD
BAT
PROG
R B
+ DC -
S
N
CELL
MODULE
© 2020 DMP
WWW.DMP.COM
Mounting Holes
Z-Wave Module
Wi-Fi
Antenna
XTLplus
Mounting Holes
Wire Exits
for DC Power Supply
Model 372-500-W
DC Plug-in
Power Supply
Use 22 AWG for
Power Supply connection
RESETLOAD
BAT
PROG
R B
+ DC -
S
N
LPC-0181 R1
CELL
MODULE
© 2020 DMP
WWW.DMP.COM
+
_
+ DC -

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
4
SECONDARY POWER SUPPLY
Standby Battery
The XTLplusINT 800 mAh rechargeable battery is used to provide 4 hours of standby battery power when DC power
is not available. The battery is intended for backup power only and not to operate the panel on a daily basis. If the
battery is low, or not plugged into the BAT battery connector, a low battery condition is indicated by the panel. If
24 hour standby battery power is needed, connect the 3500mAh battery. See Figure 3. If removing the panel from
service, disconnect the backup battery from the BAT connector.
Replacement
Use the following steps to replace the XTLplusINT standby battery. DMP recommends replacing the battery every 3
years under normal use.
1. Unplug the BAT battery connector from the XTLplusINT panel.
2. Loosen the top PCB snaps.
3. Lean the panel PCB forward and lift out from the bottom PCB snaps.
4. Remove and properly dispose of the used battery.
Caution: Risk of fire, explosion, and burns. Do not disassemble, heat above 212°F (100°C), or incinerate.
Properly dispose of used batteries.
5. Place the new battery into the XTLplusINT housing base with the battery wires directed toward the bottom
left corner. See Figure 3.
6. Set the XTLplusINT PCB into the bottom snaps and press into the top snaps to secure in place.
7. Plug the battery into the BAT panel connector.
Battery Supervision
The panel tests the battery once every hour when DC power is present. This test occurs 15 minutes past each hour and
lasts for five seconds. A load is placed on the battery and if the battery voltage is low, a low battery is detected. If DC
power has failed, a low battery is detected any time the battery voltage falls below 3.7V.
Top PCB Snaps
Bottom PCB Snaps
Battery Connector
3.8 V 3500 mAh Rechargeable Battery
(required for 24 hour standby)
3.8 V 800 mAh
Rechargeable
Battery

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
5
LED OPERATION
Backlit Logo
The backlit logo indicates the Power and Armed status of the panel. Depending on the operation, the LED displays in
Red or Green as listed in the table.
Color and Activity Operation
Green Steady Panel Disarmed, Primary Power OK, Battery OK
Green Blinking Panel Disarmed, Primary Power OK, Battery Fault
No Light Panel Disarmed, Primary Power Fault, Battery OK
Red Steady Panel Armed, Primary Power OK, Battery OK
Red/Green Alternate Panel Armed, Primary Power OK, Battery Fault
Red Blinking Panel Armed, Primary Power Fault, Battery OK
RESET BUTTON
The RESET button is located on the top of the circuit board and is used to reset the XTLplusINT. To reset the panel
prior to reprogramming, press the RESET button without powering down the system. After resetting the panel, begin
programming within 30 minutes. If you wait longer than 30 minutes, you must reset the panel again. See Figure 5 for
RESET button location.
TAMPER BUTTON
The tamper button is pressed when the cover of the XTLplusINT is secured onto the enclosure. When the cover is
removed, the XTLplusINT sends a Tamper Trouble message to the Central Station. The XTLplusINT has a second
tamper button located on the back of the unit, as shown in Figure 4. This tamper is pressed when the unit is attached
to the wall, and sends a Tamper Trouble message when the unit is removed.
PROG PROGRAMMING CONNECTION
Onsite programming can be completed using an associated wireless keypad or by connecting a hardwired keypad to
the PROG header.
ON-BOARD 1100INT SERIES WIRELESS
Wireless Antenna
The XTLplusINT Wireless Antenna is integrated into the circuit board. The panel’s built-in wireless receiver operates
with DMP 1100INT Series transmitters. See section 3.1 for a list of accessory devices.
Wireless LED Operation
The wireless LEDs are located in the upper right of the circuit board below the RESET button and function as follows:
Green: The green LED flashes every time the receiver transmits. If the panel is reset, or the panel is powered o, the
green LED is o. Under normal operation, the green LED flashes constantly with no interruption or change.
Yellow: The yellow LED flashes every time the panel receives a message from a programmed wireless transmitter.
When a message is sent by a transmitter, typically by pressing or releasing the TAMPER button, the yellow LED should
flash indicating that the panel received a message from the transmitter. If the LED never flashes, the transmitter is
not getting through to the panel. This could be because of a misprogrammed serial number or the transmitter is too
far away. Under normal operation, the yellow LED flashes at every trip of every wireless transmitter and when the
transmitters perform their periodic check-in. It is not unusual for this LED to stay o for many minutes at a time when
no transmitters are communicating. See Figure 5 for Wireless LED locations.
WIRELESS ZONES
XTLplusINT panels provide 99 wireless zones numbered 1 to 99. A default zone name, zone type, and area assignment
are provided for zones 1-48 and can be changed in Zone Information programming as needed. The defaults are
provided as a programming convenience to help reduce installation time.
WIRELESS KEY FOBS AND OUTPUTS
XTLplusINT panels provide 8 wireless key fob or output addresses numbered 51 to 54 and 61 to 64. A default name is provided as a
programming convenience to help reduce installation time. The default names are described in the programming sections of this
guide and can be changed in Output Setup or Zone Information programming as needed

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
6
FLASH LOAD BUTTON
The XTLplusINT panel software can be updated via the panel’s PROG programming header. To update the panel with
a new software version, complete the following steps at the protected premises:
Model 399 Cable
Connect a DMP 399 Cable from the PROG header to the serial port of your PC operating Remote Link and containing
the XTLplusINT RU file.
1. Start Remote Link and create or open the control panel account that matches the panel to be updated.
2. Set the Connection Information Type to Direct with a baud rate of 38400 and choose the appropriate
COM port.
3. Select Panel>Remote Update, then select the correct RU file for the panel.
4. Press and hold the LOAD button, then press and release the RESET button.
5. Release the LOAD button and click <Update> in Remote Link.
6. After the software update is completed, remove the 399 cable and press the RESET button to resume
normal panel operation.
Model 401 USB Flash Module
1. Press and hold the Reset (S1) button.
2. Connect the USB flash drive containing the firmware file to the Model 401 and connect the assembly to the
panel’s PROG header and press the button on the model 401 one time.
3. With your finger still on the Reset button, press and hold the LOAD (S2) button then release the Reset
button.
4. Press and release the button on the 401. The green LED on the 401 should start a slow flash and run for 5
minutes. If the LED blinks rapidly, the update was not successful. Press and release the Reset (S1) button to
resume normal operation and start again at Step 1.
5. After the green LED starts a slow flash, release the LOAD button.
6. After the firmware version is updated the green LED will be steady.
7. Press and hold the Reset button, remove the 401, then release the Reset button to resume normal
operation.
ON-BOARD Z-WAVE CONNECTION
The XTLplusINT features an on-board Z-Wave controller that allows short range radio control of Z-Wave devices that
you or your installation company may provide such as; lighting control modules, thermostat controls, doors, and
garage doors. Z-Wave Setup allows you to program the system to control the Z-Wave devices from Smartphones
using the DMP Virtual Keypad App or from Virtualkeypad.com. The available setup options are: Add, List, Remove,
Favorites, Transfer and Optimize.
ON-BOARD WI-FI NETWORK
The XTLplusINT connects directly to a Wi-Fi network for TCP communication using a Wireless-B/G connection. The
XTLplusINT uses wireless 802.11b/g Wi-Fi technology.
WI-FI LEDS
The Green Wi-Fi LED is located to the right of the wireless LEDs in the upper right of the circuit board.
Wi-Fi LED displays solid when the network is connected and is o when there is no network connectivity. See Figure
4 for Wi-Fi LED location.
CELLULAR CONNECTION
The CELL MODULE header is provided to connect a 265 Series Cellular Communicator. The 265LTE-INT Series
provides a fully supervised alarm communication path over an LTE network. Cellular communicators provide an
external PCB antenna. Refer to the 265LTE-INT Series Cellular Communicator Installation Guide (LT-1703INT) for
complete installation information.
Installing the 265LTE-INT on the XTLplusINT:
1. Place the antenna onto the SMA connector and twist the antenna until it is securely
tightened on the 265.
2. Keep the 265 parallel to the XTLplusINT PCB and slide it into the eight-pin CELL MODULE connector.
3. Fully seat the 265 and snap its stando hole onto the stando pin on the XTLplusINT.

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
7
WIRELESS KEYPADS
Mounting Wireless Keypads
DMP Wireless keypads have removable covers that allow the base to be mounted on a wall, desk stand or
other flat surface using the screw holes provided on each corner.
PROGRAMMING INTRODUCTION
Before You Begin
Before starting to program, we recommend you read through the contents of this manual. The information in this
document allows you to quickly learn the programming options and operational capabilities of the
XTLplusINT panel.
After this Introduction, the remaining sections describe the functions of each of the programming menu items along
with their available options. The panel contains all of its programming information in an on-board processor and does
not require an external programmer.
In addition to this manual, you should also be familiar with the following XTLplusINT documents:
• XTLplusINT User’s Guide (LT-1442INT)
• XTLplusINT Fast Programming Sheet (LT-1441FINT)
• XTLplusINT Programming Sheet (LT-1441INT)
Programming Information Sheet
Included with each XTLplusINT panel is the Programming Sheet. This sheet lists the various options available for
programming the panel. Before starting, completely fill out the sheet with the programming options you intend to
enter into the panel.
Having completed programming sheets available while entering data helps to prevent errors and can shorten the
length of time you spend programming. Completed sheets also provide you with an accurate account of the panel’s
program you can keep on file for future system service or expansion.
The remainder of the Introduction explains starting and ending a programming session.
Getting Started
Ground yourself before handling the panel! Touch any grounded metal before touching the panel to discharge static.
The panel should be completely installed before you begin programming. Make sure the AC and battery wires are
correctly installed.
Program from a Wireless or LCD Keypad
The panel can be programmed using a wireless keypad that has been auto paired or manually associated with the
panel. You can also program the panel using an LCD keypad connected to the panel PROG header.
Auto WPS
The panel oers a convenient way to connect to a Wi-Fi network. Press the WPS button on your router within 5
minutes of powering the panel to automatically connect to the Wi-Fi network.
Wireless Keypad Auto Pairing
Wireless keypad auto pairing allows you to skip the Wireless Keypad Association process and automatically connect
your keypad to the panel. Auto pairing is only available for 9862INT Series Wireless Graphics Touchscreen Keypads
(Version 700 or higher) that do not have a previously assigned house code. A maximum of seven wireless keypads are
allowed on each panel.
To pair a 9862INT Series keypad with an XTLplusINT panel, power up both the panel and the keypad. A 10 minute
pairing timer begins. The auto pairing process starts immediately and the keypad displays Pairing Keypad With
System. See Figure 7. If the panel acquires the keypad during that time, the home screen displays signaling that
pairing is complete.
If the panel does not acquire the keypad by the end of the 10 minute pairing timer, the keypad displays Pairing Failed,
followed by the Reset screen. See Figure 9 and Figure 10. Reset your panel and tap the Pair button to restart the
pairing process.
If the keypad loses communication with the panel, the No Communication With System display appears and provides
the option to reattempt pairing. See Figure 10.

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
8
Wireless Keypad Association
To enable association operation on a Wireless Graphics Touchscreen keypad, access the Options menu through the
carousel menu. While in the Options display, press the Installer Options icon. Enter the code 3577 (INST) and press
CMD. Press KPD RF to start the RF survey communication. The keypad displays its wireless serial number and RF
SURVEY.
The keypad Power/Armed LED turns Red, indicating communication has not yet been established with the panel
receiver.
To enable association operation in the XTLplusINT Series panel, press the XTLplusINT Series RESET button three
times allowing the wireless TRANSMIT LED (TX) located near the top of the PCB to begin flashing between each
press. When in keypad association, the XTLplusINT Series Red and Green logo LEDs turn on steady.
For 60 seconds, the panel listens for wireless keypads that are in RF Survey and have not been programmed, or
associated into another panel. Wireless keypads are assigned to the first open device position in Device Setup
automatically, based upon the order in which they are detected. When successful communication has been
established, the Power/Armed LED turns Blue on Graphics keypads or Green on LCD keypads.
A maximum of seven wireless keypads are allowed on each panel.
Arming Type Auto Detect (on select keypads)
When the XTLplusINT panel’s arming type (A/P, H/S/A, Area) is changed, 9862 Series keypads will automatically sync
their arming type to match the panel. This prevents you from having to manually change the keypad arming type to
match the XTLplusINT panel’s settings.
Keypad
Associate up to seven DMP 9862INT Graphic Touchscreen Wireless Keypads to the XTLplusINT panel. The operation is
shown and described in the following sections.
Special Keys
The following special keys or areas are common to all DMP keypads.
COMMAND (CMD) Key
Pressing CMD allows you to go forward through the programming menu and through each step of a programming
section. As you go through the programming, the keypad display shows any current programming already stored in
the panel memory. If no change is required for an option, press CMD to advance to the next step.
CMD is also used to enter information into the panel’s memory such as phone numbers or zone names. Press CMD
after entering information.
Back Arrow (<—) Key
Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when an error is
made while entering information. Press the Back Arrow key once to erase the last character entered.
Select Keys or Areas
The top row of keys are called the select keys on Thinline keypads or select areas on Graphic Touchscreen keypads.
Each time you need to press a select key or area, the keypad displays the function or options above one of the keys or
in the select areas. Displaying choices above individual select keys or in select areas allows them to be used for many
dierent applications. For example, you can enter AM or PM when programming the automatic test time or answer
YES or NO for a system option.
During programming, the select keys allow you to change information currently in panel memory by pressing the
appropriate select key under the display. You then enter the new information using the keypad data entry digit keys.
When there are more than four response options available, press CMD to display the remaining options. Pressing the
Back Arrow key allows you to review the previous four choices.
The select keys are also used for choosing a section from the programming menu. When the programming section
name you want displays, press any select key.
On Graphic Touchscreen Keypads, when instructed to press the first select key, touch select area 1; the second select
key touch select area 2; third select key touch select area 3; and the fourth select key touch select area 4.

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
9
Entering Characters Using the Number Pad
1. Choose a character from the table.
2. Identify the Number the character correlates with and press it on the number pad.
3. Identify the Select Key or Area for that character and press that select key or area on the keypad. Press that
select key or area again to access the uppercase letter.
4. When the desired character displays on the keypad, return to Step 1 to enter another character or press
CMD if finished.
Entering Characters Using the Standard Keyboard (Graphic Touchscreen Keypads)
• Press ABC to access uppercase letters.
• Press abc to access lowercase letters.
• Press !@# to access symbols.
• Press 123 to access the number pad.
Not all keypad prompts accept letters and/or symbols. For
example, pressing Pon the ENTER CODE prompt could
display a 6on the keypad.
Keypad Displays Current Programming
Each programming option displayed at the keypad shows the currently
selected option in the panel memory. These options are either shown as a number, a blank, or a NO or YES. To change
a number or blank to a new number, press any select key. The current option is replaced with a dash. Press the
number(s) on the keypad you want to enter as the new number for that option. It is not necessary to enter numbers
with leading zeros. The panel automatically right justifies the number when you press CMD.
To change a programming option that requires a NO or YES response, press the select key for the response not
selected. See Figure 13.
For example, if the current option is selected as YES and you want to change it to NO, press the third select key. The
display changes to NO. Press CMD to display the next option.
Programming Menu
Accessing the Programmer
To access the programmer function of the XTLplusINT:
1. Use a standard LCD keypad, connect to the PROG header, and set the keypad to Address 1.
2. Press the RESET button for two seconds.
3. Enter the code 665 (PRO). The keypad displays: PROGRAMMER.
You are now ready to start programming the XTLplusINT panel. Pressing CMD scrolls you through the programming
menu items listed below.
Menu Item Section in This Manual Menu Item Section in This Manual
Initialization 20 Bell Options 29
Fast Program 21 Output Options 30
Communication 22 Output Setup 31
Network Options 23 Area Information 32
Messaging Setup 24 Zone Information 33
Device Setup 25 Stop 34
Remote Options 26 Set Lockout Code 35
System Reports 27 Appendix 36
System Options 28
To select a section for programming, press any select key when the name of that section displays on the keypad. The
detailed instructions for each programming step are found in sections 20 to 35 of this manual. Remove the hardwired
keypad when programming is completed.
Programmer Lockout Codes
Although the XTLplusINT panel allows you to access the Programming menu without a lockout code, it is available to
program one to restrict programming access to authorized individuals only. You can do this by using SET LOCKOUT
CODE at the end of the programming menu.

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
10
Installing a lockout code
1. After entering the Programmer menu, the keypad displays PROGRAMMER. Press CMD until SET LOCKOUT
CODE is displayed (after STOP).
2. Press any select key. At the ENTER CODE: - display, enter a 1- to 5-digit programmer lockout code. Press
CMD.
3. The display shows ENTER AGAIN. Enter the same lockout code again and press CMD. The display shows
CODE CHANGED. The new code number must now be entered before the Programmer menu can be
accessed.
The lockout code should be written down and kept in a secure place with access limited to authorized persons only.
Lost Lockout Code requires factory reset: If you lose or forget the lockout code, the panel must be sent back to the
factory to be reset. There is no field option for gaining access to the panel without a valid lockout code.
Reset Timeout
The XTLplusINT has a feature that requires you to enter the Programmer within 30 minutes of resetting the panel.
After 30 minutes, if you attempt to program by entering the 665 (PRO) code, the keypad displays: RESET PANEL. You
must reset the panel and enter the program code within the next 30 minutes.
If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes, the panel
terminates programming. All data entered up to that point is saved in the panel’s memory.
To exit the panel’s Programmer you must use the Stop function. The STOP option is the second to the last option in
programming. The programming session is then terminated and the keypad returns to the Status List.
INITIALIZATION
Initialization
This function allows you to clear selected parts of the panel program back to the factory
defaults.
Clear All Codes
NO leaves existing codes intact.
YES clears the user code and user profile memory and assigns user code number 99 to
the highest user number.
Clear All Schedules
NO leaves existing schedules intact.
YES clears all shift and output schedules.
Clear Display Events Memory
NO leaves existing event memory intact.
YES clears the events memory.
Clear Zone Information
NO leaves existing zone information intact.
YES clears the zone information for all zones.
Clear Communication Options
NO leaves existing communication options intact.
YES reset communication and remote options programming to factory defaults.
Clear Wi-Fi
NO leaves existing Wi-Fi programming intact.
YES reset Wi-Fi programming to factory defaults.
Set to Factory Defaults
NO leaves existing panel programming intact.
YES sets the panel’s programming back to factory default selections. Selecting YES
does not clear the panel’s event memory, zones, user code information, or schedules.
INITIALIZATION
INITIALIZATION
CODES? NO YES
SCHEDS? NO YES
EVENTS? NO YES
ZONES? NO YES
COM/RMT? NO YES
WIFI? NO YES
DEFAULTS NO YES

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
11
INITIALIZATION
Initialization
This function allows you to clear selected parts of the panel program back to the factory
defaults.
Clear All Codes
NO leaves existing codes intact.
YES clears the user code and user profile memory and assigns user code number 99 to
the highest user number.
Clear All Schedules
NO leaves existing schedules intact.
YES clears all shift and output schedules.
Clear Display Events Memory
NO leaves existing event memory intact.
YES clears the events memory.
Clear Zone Information
NO leaves existing zone information intact.
YES clears the zone information for all zones.
Clear Communication Options
NO leaves existing communication options intact.
YES reset communication and remote options programming to factory defaults.
Clear Wi-Fi
NO leaves existing Wi-Fi programming intact.
YES reset Wi-Fi programming to factory defaults.
Set to Factory Defaults
NO leaves existing panel programming intact.
YES sets the panel’s programming back to factory default selections. Selecting YES
does not clear the panel’s event memory, zones, user code information, or schedules.
INITIALIZATION
INITIALIZATION
CODES? NO YES
SCHEDS? NO YES
EVENTS? NO YES
ZONES? NO YES
COM/RMT? NO YES
WIFI? NO YES
DEFAULTS NO YES

Digital Monitoring Products XTLplus International Series Installation and Programming Guide
12
FAST PROGRAMMING
Fast Program
The Fast Program section allows you to quickly configure the essential settings for the
XTLplusINT panel.
Account Number
Enter the account number sent to the receiver. The range of account numbers are 1 to
65535. For account numbers of four digits or less, you do not have to enter leading
zeros. The panel automatically right justifies the account number. See Communication.
First IP Address
Enter the first (primary) IP address and press CMD. The panel displays WPS? NO YES.
Press the fourth select area to choose YES. Press the WPS button on the router. WIFI
SETUP SEARCHING displays until connected to the IP address.
App Key
Enter the 8-digit App Key obtained in your Dealer Settings tab at DMPDealerAdmin.com.
See Remote Options.
System
This configures the panel as either a six Area system, an All/Perimeter system
(Perimeter/Interior), or a Home/Away system (Perimeter, Interior, and Bedrooms). See
System Options.
Hours from GMT
Enter the number (0-23) that indicates the Greenwich Time zone (GMT) where the panel
is located. See System Options.
Weather Postal Code
Enter the zip code of the panel at this option. See System Options.
Enter Siren Serial Number
Enter the eight-digit serial number for the wireless siren. The siren is automatically set to
Output 61. See Output Setup.
Zone Number
Enter the zone number to program. See Zone Information.
Zone Name
Press any select area to display the default zone name. To change the default zone
name, press any select area to clear name. Enter up to 16 characters for the new zone
name.
Zone Type
To change the default zone type press any select area. See Zone Information.
Area Assignment
To change the default area, press any select area.
Serial Number Entry
Enter the eight digit serial number, including leading zeros, found on the wireless device.
Stop
Press CMD to display STOP and press any select area to exit the Fast Program function
and save the programming. All programming options are still available by reentering the
programming menu.
FAST PROGRAM
ACCOUNT NO:
FIRST IP ADDR
WPS? NO YES
APP KEY:
SYSTEM: ALL/PERIM
AREA A/P H/A
HRS FROM GMT: 6
WEATHER POSTAL
CODE: 0
ENTER SIREN
SERIAL #: -
ZONE NO: -
* DEFAULT NAME *
ZONE TYPE: -
AREA: -
SERIAL #: -
STOP

XTLplus International Series Installation and Programming Guide Digital Monitoring Products
13
COMMUNICATION
Communication
The Communication section allows you to configure the communication settings for the
XTLplus INT panel.
Account Number
Enter the account number sent to the receiver.
DD, NET, CELL - The range of account numbers for Digital Dialer, Network, and Cell is 1
to 65535. For account numbers of four digits or less, you do not have to enter leading
zeros. The panel automatically right justifies the account number.
CID - The account number range for this format is 1 - 9999.
Transmission Delay
Enter the number of seconds (15 to 45 seconds) the panel waits before sending burglary
alarm reports to the receiver. The wireless siren and relay outputs are not delayed during
this period. Enter 0 (zero) to disable this function. The default is 30.
Communication Type
This specifies the communication method the panel uses to contact the receiver. Press
any select area to display the following communication options:
• WIFI: Network communication to DMP Model SCS-1R or SCS-VR Receivers.
• CEL: This option allows communication over the cellular network using the 265LTE-
INT Series Cellular Communicator to DMP Model SCS-1R or SCS-VR Receivers.
• NONE: For local systems. Selecting this ends communication programming.
If automatic cellular activation is unsuccessful, cellular communication must be activated
using the Activate Cell option provided in Diagnostics Function located in the Appendix.
Backup Cellular
Backup Cellular option is available if COMM TYPE is set for WIFI. The Backup Cellular
tries to send the message after the main communication fails for 60 seconds on WIFI. If
the backup cellular fails then the message is discarded.
Test Time
Press CMD to enter the Test Time. Enter the time of day the panel sends the test report
to the SCS-1R Receiver. Use entries between 12:00 to 11:59 and then choose AM or PM.
Test Days
Enter how often the panel test report is sent to the receiver. Enter from 1 to 60 days.
Enter zero to disable the test report.
Default is 1 (one) day. This option only displays if a
test time is entered.
Check-In Minutes
Check-in reports are a method of supervising the panel for communication with the
receiver. Enter the number of minutes between check-in reports. Select from 0 or 3-240
minutes. Entering 0 (zero) disables the check-in option. Default is 0. If the Cell Check-In
option is used, additional cell charges may apply.
Fail Time
Fail Time allows the receiver to miss a defined number of check-in minutes before
logging that the panel is missing. For example, if CHECKIN minutes is 20 and Fail TIME
minutes is 30, the receiver only indicates a Panel Not Responding after 30 minutes. The
Fail TIME must be equal to or greater than the CHECKIN minutes: If the CHECKIN is 20
minutes, the FAIL TIME must be 20 or more. The maximum FAIL TIME is 240 minutes.
The default FAIL TIME is 240 minutes.
COMMUNICATION
ACCOUNT NO:
XMIT DELAY: 30
COMM TYPE: CELL
WIFI CEL NONE
BACKUP CELL
NO YES
TEST TIME
00:00 AM
TEST DAYS: 1
CHECKIN: 0
FAIL TIME: 240