DMP Electronics 1103 Series User manual

INSTALLATION GUIDE
1103 Series
Wireless Universal Transmitter

1103 Series Installation Guide | Digital Monitoring Products 1
GET STARTED
The 1103 Series Wireless Universal Transmitters are two-way supervisory wireless transmitters typically used for
commercial fire or burglary door and window applications. The 1103E features 128-bit AES encryption.
The transmitter provides a cover tamper, magnetic reed switch, and an onboard terminal block for external contact
wiring. Both sets of contacts can be programmed to operate at the same time. This allows two independent zones to
operate from one 1103.
The 1103 Series also features Disarm/Disable functionality. When this option is enabled, Zone Tripped messages are
disabled when the system is disarmed.
What’s Included
▶One 1103 Transmitter
▶One Commercial Magnet
▶One 470K EOL Resistor
▶One 3 V lithium CR123A battery
▶Hardware pack
Compatibility
▶All DMP 1100 Series Wireless Receivers
▶All DMP XT Series and XR Series panels
Note: To enable encryption on 1103E models, Version 183 is required for XT and XR Series panels and Version
300 is required for Wireless Receivers.
Procedure
To install an 1103, this guide walks you through these required steps:
1. Program the panel.
2. Install the battery.
3. Use the LED Survey to select a location.
4. Mount the transmitter.
5. Wire external contacts (optional).
6. Test the transmitter.
PCB Layout
Figure 1: 1103 Layout
External Contact
Terminal Block
Magnetic Reed Switches
Survey LED
Tamper Switch

1103 Series Installation Guide | Digital Monitoring Products 2
INSTALLATION
1 Program the Panel
Refer to the panel programming guide as needed. After completing each of the following steps, press CMD to
advance to the next prompt.
1. At a keypad, enter 6653 (PROG) to access the Programmer Menu.
2. For an 1103E, use the two steps below and then continue to step 3. Otherwise, go to step 3.
▶Go to SYSTEM OPTIONS. At 1100ENCRYPTION, select ALL to only add encrypted wireless devices
to the system. Select BOTH to allow both encrypted and non-encrypted wireless devices to be
programmed.
▶The default passphrase appears at the ENTER PASSPHRASE prompt. Press CMD to keep the default.
Press any select key or area to change the passphrase and enter an 8-character hexadecimal string
(0-9, A-F).
3. At ZONE INFORMATION, enter the wireless zone number you would like to use (must begin in the 500
range when using XR panels).
4. At *UNUSED*, enter the zone name.
5. At ZONE TYPE, press any select key or area and select the zone type.
6. At the NEXT ZN? prompt, select NO.
7. When WIRELESS? displays, select YES.
8. At SERIAL#, enter the eight-digit device serial number found on device packaging.
9. At CONTACT, select either INTERNAL or EXTERNAL. Use consecutive zone numbers if using both internal
and external contacts.
10. At SUPRVSN TIME, enter a supervision time. Default is 240.
11. At DISARM DISABLE, select NO or YES.
Note: Program the external contact first if using both internal and external contacts with
Disarm/Disable functionality.
12. At the NEXT ZONE prompt, select YES if you are finished programming the zone. Select NO if you would
like to access additional programming options.
13. To save panel programming, go to STOP and press CMD.
2 Install the Battery
Use a 3.0V lithium battery, a DMP Model CR123A battery, or an equivalent model from Sony or Murata. For listed
installations, use either an Energizer® 123battery or a CR123A battery manufactured by Panasonic or Tekcell.
1. Push the button on the end of the transmitterand separate the two halves.
2. Observing polarity, place the battery in the holder and press it into place. Refer to Figure 1during
installation.

1103 Series Installation Guide | Digital Monitoring Products 3
Use the LED Survey to Select a Location
The 1103 Series Wireless Univeral Transmitter provides a Survey LED capability to allow one person to confirm
communication with the wireless receiver or panel while the cover is removed.
1. With the cover removed, hold the transmitter in the exact desired location.
2. Press the tamper switch to send data to the panel and determine if communication is confirmed or faulty.
Confirmed: If communication is confirmed, for each press or release of the tamper switch the LED blinks
immediately on and immediately o. Repeat this test to confirm five separate consecutive LED blinks. Any
indication otherwise means proper communication has not been established.
Faulty: If communication is faulty, the LED remains on for about 8 seconds or flashes multiple times in
quick succession. Relocate the transmitter until the LED confirms clear communication.
3
4
Mount the Transmitter
Mount the Housing
When mounting the 1103, refer to Figure 1 and Figure 2 for
battery and mounting hole locations.
1. Remove the battery and the PCB.
2. Place the supplied #4screw into the mounting hole
and secure the transmitter to the surface.
3. Insert the included tamper screw and tamper as
shown in Figure 2.
4. Reinsert the PCB and the battery.
5. Snap the transmitter cover back onto the base.
Mount the Magnet
For magnet placement options, see Figure 4.
Commercial Installation
Place and hold the magnet cover directly on the door
closest to the magnetic reed switch, no more than 1/2”
(1.3cm) apart from the transmitter. Use the provided
#4screws to mount the magnet. See Figure 3.
Figure 2: Mounting the Transmitter
PCB Latch
Tamper
Mounting
Screws
Tamper
Screw
Figure 3: Commercial Installation
Figure 4: Placement Options

1103 Series Installation Guide | Digital Monitoring Products 4
5 Wire External Contacts (Optional)
DMP recommends using 18or 22AWG unshielded wire. It is recommended to locate a contact within 100 feet of
the transmitter. Connect the contact as normally open (N/O) or normally closed (N/C) with the 470K end-of-line
resistor. For UL listed installations, program the external contact as Normally Closed (N/C). Refer to the Contact
option under Zone Information in the appropriate panel programming guide.
If you use both the magnet reed switch in the transmitter and an external contact, use consecutive zone numbers
when connecting them to the panel.
1. Use a flathead screwdriver to loosen the two screws on the external contact terminal block.
2. Insert external contact wiring into the terminal block and tighten the screws.
3. Connect the other ends of the wires to the external contact as either normally open (N/O) or normally
closed (N/C) with the included 470K end-of-line resistor.
4. Snap the transmitter cover back onto the base.
6
Test the Transmitter
After the transmitterhas been installed, test to confirm that it is communicating reliably with the panel. Use
the Tech APP™ to perform a Wireless Check-in Test on the system or complete the following steps to perform a
Check-in Test from a keypad that is connected to the panel. At the keypad, enter 8144 (WALK) and select WLS.
Figure 5: Installing External Contacts
Parallel for N/O
Series for N/C
External Contact
Terminal Block
1103
Door
Window
External
Contact
Magnet
Program an internal
contact as the next
consecutive zone. Program an external
contact as the first zone.

1103 Series Installation Guide | Digital Monitoring Products 5
ADDITIONAL INFORMATION
Supervision Time
When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the
receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour
to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life for
transmitters. A missing message may display on the keypad until the transmitter sends a supervision message.
Replace the Battery
1. Push the button on the end of the transmitterand separate the two halves.
2. Remove the old battery, observe polarity, and place the new battery in the holder.
3. Snap the cover back on the transmitter.
Sensor Reset to Clear LOBAT
Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message. On an LCD keypad,
press and hold 2for two seconds. On a graphic touchscreen keypad, press RESET. Enter your user code, if required.
The keypad displays SENSORS OFF followed by SENSORS ON.
Compatibility
The 1103 has been designed primarily for use with the XR150/XR550 Series control panels. However, it can be used
with the XT30/XT50 or XTL Series panels as well. When used with those panels, the tamper indication is sent via
the internal contact zone only. If using the external contact, the internal contact must also be programmed in a
separate zone to provide tamper indication. In addition, the supplied magnet must be mounted next to the 1103
internal contact to restore the zone and allow the tamper switch to have priority. This issue does not exist when the
transmitter is installed with the XR150/XR550 Series panels.

1103 Series Installation Guide | Digital Monitoring Products 6
SPECIFICATIONS
Battery
Life Expectancy 5 years (normal operation)
Type 3.0V lithium CR123A
Frequency Range 905-924 MHz
Dimensions
Transmitter Case 3.3 L x 1.6 W x 1.0 H in.
Transmitter Base 3.3 L x 1.6 W x 0.1 H in.
Magnet Housing 1.5 L X 0.5 W X 0.7 H in.
Housing Material Flame retardant ABS
Encryption
▶XT and XR Series Panels Version 183 or higher
▶Wireless Receivers Version 300 or higher
CERTIFICATIONS
▶California State Fire Marshal (CSFM)
▶FCC Part 15 Registration ID CCKPC0191
▶New York City (FDNY)
▶Industry Canada Registration ID 5251A-PC0191
Underwriters Laboratory (UL) Listed
ANSI/UL 365 Police Station Connected Burglar
ANSI/UL 609 Local Burglar Alarm Units and Systems
ANSI/UL 634 Connections and Switches for use with Burglar Alarm Systems
ANSI/UL 1023 Household Burglar Alarm System Units
ANSI/UL 1076 Proprietary Burglar Alarm Units
ANSI/UL 1610 Central Station Burglar Alarm Units
ANSI/UL 864 Fire Protective Signaling Systems
Patents
▶U. S. Patent No. 7,239,236

18205
Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-0702 1.05 21373
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
© 2021
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Information
This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.