DMP Electronics SecuraHub Series Installation guide

INSTALLATION AND PROGRAMMING GUIDE
SecuraHub™SERIES PANELS

MODEL SecuraHub™ SERIES
INSTALLATION AND PROGRAMMING GUIDE
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device has been designed to operate with the integrated 1100 Series PCB antenna having a maximum
gain of 1.0 dB. Antennas having a gain greater than 1.0 dB are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
If necessary, the installer should consult the dealer or an experienced radio/television technician
for additional suggestions. The installer may nd the following booklet, prepared by the Federal
Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Oce, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2018 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

SecuraHub Installation and Programming Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Panel Specications
1.1 Power Supply ......................................................................................................... 1
1.2 Communication ...................................................................................................... 1
1.3 Keypads................................................................................................................. 1
1.4 Number of Zones.................................................................................................... 1
1.5 EnclosureSpecications .......................................................................................... 1
Introduction
2.1 SystemCongurations ............................................................................................ 1
2.2 Caution Notes ........................................................................................................ 1
2.3 Compliance Instructions.......................................................................................... 1
System Components
3.1 Accessory Devices .................................................................................................. 2
Installation
4.1 Location Information .............................................................................................. 4
Primary Power Supply
5.1 DC Input................................................................................................................ 4
Secondary Power Supply
6.1 Standby Battery ..................................................................................................... 4
6.2 Replacement .......................................................................................................... 5
6.3 Battery Supervision................................................................................................. 5
LED Operation
7.1 Power LED ............................................................................................................. 5
RESET Button
8.1 Description............................................................................................................. 5
PROG Programming Connection
9.1 Description............................................................................................................. 6
On-Board Wireless
10.1 Wireless Antenna.................................................................................................... 6
10.2 Wireless LED Operation........................................................................................... 6
Wireless Zones
11.1 Description............................................................................................................. 6
Wireless Key Fobs and Outputs
12.1 Description............................................................................................................. 6
On-Board Z-Wave Connection
13.1 Description ............................................................................................................ 6
On-Board Wi-Fi Network
14.1 Description............................................................................................................. 6
14.2 Wi-Fi LEDs ............................................................................................................. 6
Cellular Connection
15.1 Description............................................................................................................. 7
16.1 BeforeYouBegin.................................................................................................... 8
16.2 GettingStarted....................................................................................................... 8
16.3 Keypad .................................................................................................................. 9
16.4 Enter Characters - Standard DMP Keypad................................................................10
16.5 Enter Characters - Alphanumeric Keypad.................................................................10
Fast Programming
17.1 FastProgram.........................................................................................................11
17.2 Account Number....................................................................................................11
17.3 First IP Address.....................................................................................................11
17.4 App Key ................................................................................................................11
17.5 System .................................................................................................................11
17.6 Hours from GMT....................................................................................................11
17.7 Weather Zip Code..................................................................................................11
17.8 Enter Siren Serial Number ......................................................................................11
17.9 Zone Number ........................................................................................................11

Digital Monitoring Products SecuraHub Installation and Programming Guide
ii
TABLE OF CONTENTS
17.10 Zone Name ...........................................................................................................11
17.11 Zone Type.............................................................................................................11
17.12 AreaAssignment ...................................................................................................11
17.13 Serial Number Entry ..............................................................................................11
17.14 Stop .....................................................................................................................11
Listed Compliance Specications
18.1 Introduction ..........................................................................................................12
18.2 UseMarking..........................................................................................................12
18.2 LocationsandWiring .............................................................................................12
18.3 NFPA 72 ...............................................................................................................12
18.4 Types Of Service....................................................................................................12
18.5 Police Station Phone Numbers ................................................................................12
18.6 Bypass Reports......................................................................................................12
18.7 SystemTesting......................................................................................................12
18.8 FCC Notice ............................................................................................................12
Household Burglar-Alarm System Units
ANSI/UL 1023
19.1 BellCuto.............................................................................................................13
19.2 Entry Delay ...........................................................................................................13
19.3 Exit Delay .............................................................................................................13
19.4 Wireless External Contact.......................................................................................13
19.5 Wireless Supervision Time......................................................................................13
19.6 Wireless Audible Annunciation ................................................................................13
19.7 Panel location........................................................................................................13
19.8 Test Frequency......................................................................................................13
Household Fire Warning System
ANSI/UL 985 NFPA 72 Specications
20.1 BellOutputDenition.............................................................................................13
20.2 Household System.................................................................................................13
20.3 Wireless Supervision Time......................................................................................13
20.4 WirelessFireVerication ........................................................................................13
20.5 Battery Standby ....................................................................................................13
20.6 Test Frequency......................................................................................................13
Emergency Evacuation Plans
21.1 Overview ..............................................................................................................14
False Alarm Reduction Programmable Options
ANSI/SIA CP-01-2010
22.1 ShippingDefaultsandRecommendedProgramming.................................................15
Revisions to This Document
Certications
Ordering Information
Accessories

SecuraHub Installation and Programming Guide Digital Monitoring Products
1
INTRODUCTION & PANEL SPECIFICATIONS
Panel Specications
1.1 Power Supply
12 VDC plug-in DC power supply
Input: 120 VAC, 60 Hz .2A
Output: 12 VDC .5A
Standby Battery: DMP 3.8 VDC Lithium, 800 mAh
Optional Standby Battery DMP 3.8 VDC Lithium, 3500 mAh
All circuits inherent power limited
1.2 Communication
Optional 263LTE-V-GW cellular module to send messages to DMP Model SCS-1R or SCS-VR Central Station
Receivers.
Built-in Wi-Fi™ network alarm signal communication to DMP Model SCS-1R or SCS-VR Central
Station Receivers.
1.3 Keypads
You can associate up to 7 SecuraTouch™ Keypads numbered 2-8.
1.4 Number of Zones
• SecuraHub™ has 99 wireless initiating zones numbered 1-99
• Output numbers 51 to 54 and 61 to 64 can support key fobs, output modules, or sirens
1.5 Enclosure Specications
Size Color
5.8” W x 3.8” H x 1.75” D White (W)
Introduction
2.1 System Congurations
The panel can be programmed to operate as any of the following system types:
• All/Perimeter system that provides one perimeter area and one interior area
• Home/Sleep/Away system that provides one perimeter, one interior, and one bedroom area. The
bedroom area provides for any protection devices the user wants disarmed during their sleeping hours
and armed in the Away mode.
2.2 Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing
the panel. These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you
completely read and understand its information. Failing to follow the caution note can cause damage to the
equipment or improper operation of one or more components in the system.
2.3 Compliance Instructions
For applications that must conform to a local authority’s installation standard or a National Recognized
Testing Laboratory certicated system, please see the Listed Compliance Specications section near the end
of this guide for additional instructions.

Digital Monitoring Products SecuraHub Installation and Programming Guide
2
SYSTEM COMPONENTS
System Components
3.1 Accessory Devices
Cellular Communicator Cards
265LTE-V-GW Cellular Communicator Allows you to connect the SecuraHub to any compatible Verizon LTE network.
SecuraTouch™ Keypads
9862USB Keypad with Deskstand A 5” wireless touchscreen display with deskstand. Interactive shield for quick
arming/disarming with a carousel menu. Display turns red in alarm.
9862 Keypad for Wall Mount A 5” wireless touchscreen display suitable for wall mounting. Interactive shield for
quick arming/disarming with a carousel menu. Display turns red in alarm.
SecuraSensor™ Devices
1101 Universal Transmitter Provides two internal reed switches and a terminal block to allow for external
wiring. Both sets of contacts can be programmed to operate at the same time,
allowing for two zones from one transmitter.
1106 Universal Transmitter The universal door/window transmitter is less than half the size of other wireless
transmitters. It provides an internal reed switch and a terminal block to allow for
external wiring. Both sets of contacts can be programmed to operate at the same
time, allowing for two zones from one transmitter.
1107 Micro Window Transmitter* A single reed switch that detects a window-mounted magnet.
1114 Universal Four Zone Expander* The wireless universal expander allows for connection to other types of devices. It is
handy for upgrading existing systems.
1121 PIR Motion Detector* Provides 50’X50’ coverage with a 90° eld of view and pet immunity up to 40lbs.
Ceiling/wall mounting bracket included.
1127W PIR Motion Detector Provides 36’X36’ coverage with an 84° eld of view and pet immunity up to 40lbs.
The unit allows the sensor to congure its sensitivity, pulse count or place in a walk-
test, or use disarm/disable all over-the-air remotely.
1129 Glassbreak Detector* Wireless omni-directional 360° coverage detector for frequencies specic to
breaking glass.
SecuraSounder™ Devices
1135 Siren* The 110db wireless battery-powered siren allows you to easily install wherever it
is necessary.
SecuraLight™ Devices
1118R Remote Indicator Light* Provides a visual LED for clearly displaying the system’s armed/disarmed or alarm
status.
1137 Wireless LED Emergency Light* Comes on when an alarm is triggered or activated by other system events, or by the
app. It provides emergency indoor-path lighting even when the AC power is lost.
SecuraRemote™ Devices
1144-4 (Four-Button)*
1144-2 (Two-Button)*
1144-2P (Two-Button with Prox)*
Durable water-resistant transmitter with ergonomic button design for ease of use
and a status-feedback LED. The buttons intuitively arm and disarm the system, and
include a built in panic button.
SecuraSmoke™ Devices
1164 Wireless Synchronized Smoke
Detector
The Smoke Detector is a wireless sensor with integrated synchronized sounder.
Installed with multiple smoke detectors, when one sounds, they all sound.
1183-135F Heat Detector Detects when the air temperature rises above 135°.
1183-135R Heat Detector The rate-of-rise and xed temperature detector alarm detects when there is a rapid
rise in the air temperature or if the air temperature increases at a minimum rate of
15°F per minute or reaches 135°.
1184 Carbon Monoxide Detector Provides early warning of elevated CO levels in the air.
SecuraProx™ Devices
1306P Proximity Patch* A small, adhesive credential that adheres to nearly anything and allows for codeless
arming and disarming when used with the reader built into the touchscreen keypad.
1346 Proximity Key* Impact resistant credential that ts on any standard key ring and allows for codeless
arming and disarming when used with the reader built into the touchscreen keypad.

SecuraHub Installation and Programming Guide Digital Monitoring Products
3
SYSTEM COMPONENTS
Communicators
ICOMSLZ-SCA Universal Network
Communicator with Z-Wave
With this simple network communication add-on, you can upgrade almost any panel
to take advantage of remote-system management and control features. Program
your own account number to easily work around existing installed systems.
CELLCOMZ-LTE-V Universal Cell
Communicator with Z-Wave
With this simple cellular communication add-on, you can upgrade almost any panel
to take advantage of remote-system management and control features. Program
your own account number to easily work around existing installed systems.
SecureCom™ Video Devices
V-4010B-1 Video Indoor/Outdoor Bullet
Camera*
1.3 megapixel resolution and IR LEDs for no/low light imaging at up to 30 meters.
V-4020C-1 Video Indoor Cube PIR Camera* 1.3 megapixel resolution, PIR detection and IR LEDs for no/low light imaging at up to
10 meters.
V-4030PT-1 Video Pan Tilt Indoor Camera* 1.0 megapixel resolution, PIR detection and IR LEDs for no/low light imaging at up to
10 meters. The Motorized Indoor Camera also features pan/tilt rotation.
V-4050D-1 Video Fixed Dome Camera* 1.3 megapixel resolution and IR LEDs for no/low light imaging at up to 30 meters.
V-IP1006RR Video WAP* This high-speed Wireless Access Point (WAP) comes pre-congured for easy setup
with SecureCom Video cameras or the SecuraHub. WPS encrypted connection pairs
with a push of a button.
Z-Wave™ Automation Devices
Z-GD00Z-4 Garage Door Controller* Compatible with virtually any automatic garage door opener. Installers simply attach
the unit to the current garage door opener and install a simple wireless position
sensor to provide positive control of the garage door.
Z-PS15Z-2 Light Module* Enables dimmable remote control of lights or lamps. Simply plug the module into a
wall outlet and then plug in your existing lamp or light.
Z-PD300Z-2 Appliance Module* Enables remote control of lights or small appliances. Simply plug the module into a
wall outlet and then plug in your existing lamp or appliance.
Z-LB60Z-1 LED Lightbulb* Installs into any normal light socket, making it the fastest and most ecient way to
control lighting in a home.
Z-5010T Thermostat* Fully programmable to provide complete control of an HVAC system. Its battery-only
operation means it does not require the 5th wire, making a quick installation.
Z-99140-001 Lock with Keypad, Brass*
Z-99140-002 Lock with Keypad, Nickel*
Z-99140-003 Lock with Keypad, Bronze*
Z-99100-061 Lock without Keypad, Brass*
Z-99100-062 Lock without Keypad, Nickel*
Z-99100-063 Lock without Keypad,
Bronze*
Kwikset™ Z-Wave locks.
* These devices have not been investigated and shall not be used in listed installations.

Digital Monitoring Products SecuraHub Installation and Programming Guide
4
INSTALLATION
Installation
4.1 Location Information
Select a location that is centrally located between the wireless sensors used in the installation. Place the
SecuraHub™ away from metal objects. Placing the panel on or near metal surfaces impairs performance.
When selecting the proper mounting location of a transmitter, refer to the LED Survey Operation section of
the specic installation guide for the transmitter being installed.
Primary Power Supply
5.1 DC Input
For the DC plug-in power supply, place the panel near a 120 Volt AC, 60 Hz dedicated outlet not controlled
by a switch. In addition to powering the panel, the DC plug-in power supply also charges the back-up
battery. See Figure 1.
Secondary Power Supply
6.1 Standby Battery
The SecuraHub™ 800 mAh rechargeable battery is used to provide 4 hours of standby battery power when
DC power is not available. The battery is intended for backup power only and not to operate the panel on
a daily basis. If the battery is low, or not plugged into the BAT battery connector, a low battery condition is
indicated by the panel. If 24 hour standby battery power is needed, connect an optional 3500 mAh battery.
See Figure 2.
Note: If removing the panel from service, disconnect the backup battery from the BAT connector.
Figure 1: SecuraHub™ Power Supply

SecuraHub Installation and Programming Guide Digital Monitoring Products
5
INSTALLATION
6.2 Replacement
Use the following steps to replace the SecuraHub™ standby battery. Replacing the battery every 3 years
under normal use is recommended.
1. Unplug the BAT battery connector from the SecuraHub™ panel. See Figure 2.
2. Remove and properly dispose of the used battery.
Caution: Risk of re, explosion, and burns. Do not disassemble, heat above 212°F (100°C), or
incinerate. Properly dispose of used batteries.
3. Place the new battery into the SecuraHub™ housing with the battery wires directed toward the bottom
left corner.
4. Set the SecuraHub™ PCB into the bottom snaps and press into the top snaps to secure in place.
5. Plug the battery into the BAT panel connector.
6.3 Battery Supervision
The panel tests the battery once every hour when DC power is present. This test occurs 15 minutes past
each hour and lasts for ve seconds. A load is placed on the battery and if the battery voltage is low, a low
battery is detected. If DC power has failed, a low battery is detected any time the battery voltage falls
below 3.7 V.
LED Operation
7.1 Power LED
The SecuraHub™ blue LED indicates the power status of the panel.
Activity Operation
Steady Primary Power OK, Battery OK
No Light Primary Power Fault, Battery Fault
Blinking Primary Power Fault, Battery OK
RESET Button
8.1 Description
The RESET button is located below the BAT connector and is used to reset the SecuraHub™ microprocessor.
To reset the panel prior to reprogramming, press the RESET button without powering down the system.
After resetting the panel, begin programming within 30 minutes. If you wait longer than 30 minutes, you
must reset the panel again.
Top PCB Snaps
Bottom PCB Snaps
Battery
Connector
3.8V 3500mAh Rechargeable Battery
(required for 24 hour standby)
3.8V 800mAh
Rechargeable
Battery
Figure 2: Standby Battery Replacement

Digital Monitoring Products SecuraHub Installation and Programming Guide
6
INSTALLATION
PROG Programming Connection
9.1 Description
Onsite programming can be completed using an associated wireless keypad or by connecting a hardwired
keypad to the PROG header.
On-Board Wireless
10.1 Wireless Antenna
The SecuraHub™ wireless antenna is integrated into the circuit board. The panel’s built-in wireless receiver
operates with Secura™ wireless sensors. See Section 3.1 for a list of accessory devices.
10.2 Wireless LED Operation
The wireless LEDs are located in the upper right of the circuit board and
function as follows:
Green: The green LED ashes every time the receiver transmits (32 times
per second). If the panel is reset, or the panel is powered o, the green
LED is o. Under normal operation, the green LED ashes constantly with no
interruption or change.
Yellow: The yellow LED ashes every time the panel receives a message from
a programmed wireless transmitter. When a message is sent by a transmitter,
typically by pressing or releasing the TAMPER button, the yellow LED should
ash indicating that the panel received a message from the transmitter. If the LED never ashes, the
transmitter is not getting through to the panel. This could be because of a misprogrammed serial number
or the transmitter is too far away. Under normal operation, the yellow LED ashes at every trip of every
wireless transmitter and when the transmitters perform their periodic check-in. It is not unusual for this LED
to stay o for many minutes at a time when no transmitters are communicating. See Figure 3 for Wireless
LED locations.
Wireless Zones
11.1 Description
SecuraHub™ panels provide 99 wireless zones numbered 1 to 99. A default zone name, zone type, and area
assignment are described and can be changed in Zone Information programming as needed. The defaults are
provided as a programming convenience to help reduce installation time.
Wireless Key Fobs and Outputs
12.1 Description
SecuraHub™ panels provide eight wireless key fob or output addresses numbered 51 to 54 and 61 to
64. A default name is provided as a programming convenience to help reduce installation time. The default
names are described in the programming sections of this guide and can be changed in Output Information or
Zone Information programming as needed.
On-Board Z-Wave Connection
13.1 Description
The SecuraHub™ features an on-board Z-Wave controller that allows short range radio control of Z-Wave
devices that you or your installation company may provide such as; lighting control modules, thermostat
controls, doors, and garage doors. Z-Wave Setup allows you to program the system to control the Z-Wave
devices from Smartphones using the Secura App™.
On-Board Wi-Fi Network
14.1 Description
The SecuraHub™ connects directly to a Wi-Fi network for TCP communication using a Wireless-B/G
connection. The SecuraHub™ uses wireless 802.11b/g Wi-Fi technology.
14.2 Wi-Fi LEDs
The Green Wi-Fi LED is located to the right of the wireless LEDs in the upper right of the circuit board.
Wi-Fi LED displays solid when the network is connected and is o when there is no network connectivity. See
Figure 3 for the Wi-Fi LED’s location.
RESETLOAD
XTL PLUS
BAT
PROG
R B
+ DC -
S
N
LEV
LPC-0181 R1
INSTALL GUIDE
LT-1434
CELL
MODULE
© 2015 DMP
WWW.DMP.COM
Red LED
Green LED
Green
Transmit
LED
Yellow
Receive
LED
WiFi
LED
TAMPER
Button
Figure 3: SecuraHub™
Wireless LED’s

SecuraHub Installation and Programming Guide Digital Monitoring Products
7
INSTALLATION
Cellular Connection
15.1 Description
The CELL MODULE header is provided to connect a 265LTE-V-GW Cellular Communicator. The 265LTE-V-GW
provides a fully supervised alarm communication path over the Verizon LTE network. Refer to the
265LTE-V-GW Cellular Installation Guide (LT-1703-GW) for complete installation information.
Installing the 265LTE-V-GW on the SecuraHub:
Caution: Touch grounded metal to discharge static before handling the SecuraHub PCB.
1. Remove power from the SecuraHub.
2. Remove the SecuraHub housing latch and slide the cover, containing the PCB, apart from the base.
3. Insert the 265LTE-V-GW into the eight-pin cell module header, keeping it parallel to the PCB.
4. Snap the 265LTE-V-GW on to the stando and secure it in place.
5. Remove the backing from the exible antenna and place it inside the housing base. See Figure 4.
6. Snap the antenna on to the 265LTE-V-GW on-board antenna connector.
7. Slide the SecuraHub cover back into place, ensuring the antenna stays in contact with the 265LTE-V-
GW.
8. Replace the housing latch and return power to the SecuraHub.
RESETLOAD
BAT
PROG
R B
+ DC -
S
N
Base
Cover and
PCB
Stando
On-board
Antenna
Connector
Flexible Antenna
Cell Module
Connector
Figure 4: 265 Installed on the SecuraHub™

Digital Monitoring Products SecuraHub Installation and Programming Guide
8
PROGRAMMING INTRODUCTION
Programming Introduction
16.1 Before You Begin
Before starting to program, we recommend you read through the contents of this manual. The information in
this document allows you to quickly learn the fast programming options and operational capabilities of the
SecuraHub™ panel.
16.2 Getting Started
Ground yourself before handling the panel! Touch any grounded metal before touching the panel to
discharge static. The panel should be completely installed before you begin programming. Make sure the DC
and battery wires are correctly installed.
Program from a Wireless or LCD Keypad
The panel can be programmed using a wireless keypad that has been auto paired or manually associated
with the panel. You can also program the panel using an LCD keypad connected to the panel PROG header.
Auto WPS
The panel oers a convenient way to connect to a Wi-Fi network. Press the WPS button on your router
within 5 minutes of powering the panel to automatically connect to the Wi-Fi network.
Wireless Keypad Auto Pairing
Wireless keypad auto pairing allows you to skip the Wireless Keypad Association process and automatically
connect your keypad to the panel. Auto pairing is only available for SecuraTouch™ Keypads that have not
been previously paired with a system. A maximum of four wireless keypads are allowed on each panel.
To pair a SecuraTouch™ keypad with an SecuraHub™ panel, power up both the panel and the keypad. A 10
minute pairing timer begins. The auto pairing process starts immediately and the keypad displays Pairing
Keypad With System. See Figure 5. If the panel acquires the keypad during that time, the home screen
displays signaling that pairing is complete. See Figure 6.
If the panel does not acquire the keypad by the end of the 10 minute pairing timer, the keypad displays
Pairing Failed, followed by the Reset screen. See Figure 7. Reset your panel and tap the Pair button to
restart the pairing process.
If the keypad loses communication with the panel, the No Communication With System display appears and
provides the option to reattempt pairing. See Figure 8.
Arming Type Auto Detect
When the SecuraHub™ panel’s arming type (A/P, H/S/A) is changed, SecuraTouch™ keypads will automatically
sync their arming type to match the panel. This prevents you from having to manually change the keypad
arming type to match the SecuraHub™ panel’s settings.
Pairing Keypad With System...
Figure 5: Auto Pairing in Progress Display
DISARMED
Panic
Chime
Reset
Favorites
CURRENT
HI LO
98
98 77
Figure 6: Home Screen Display
12
Reset your
System.
Press button:
PAIR
Figure 7: Auto Pairing Reset Display
No Communication With System
Press To Pair With System
?
Figure 8: Auto Pairing No Communication Display

SecuraHub Installation and Programming Guide Digital Monitoring Products
9
PROGRAMMING INTRODUCTION
16.3 Keypad
Associate up to four SecuraTouch™ keypads to the SecuraHub™ panel. Their operation is shown and described
in the following sections.
COMMAND (CMD)
Pressing CMD allows you to go forward through the programming menu and through each step of a
programming sec tion. As you go through the programming, the keypad display shows any current
programming already stored in the panel memory. If no change is required for an option, press CMD to
advance to the next step.
CMD is also used to enter information into the panel’s memory such as phone numbers or zone names. Press
CMD after entering information.
Back Arrow (<—)
Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when an
error is made while entering in formation. Press the Back Arrow key once to erase the last character entered.
Select Areas
Graphic Touchscreen keypads have a top row of select areas. Each time you need to press a select area, the
keypad displays the function or options. Displaying choices in individual select areas allows them to be used
for many dierent applications. For example, you can enter AM or PM when programming the automatic test
time or answer YES or NO for a system option.
During programming, select areas allow you to change infor mation currently in panel memory by pressing
the appropriate select area under the display. You then enter the new information using the keypad data
entry digit areas.
When there are more than four re sponse options avail able, press COMMAND to display the remaining options.
Pressing the Back Arrow allows you to review the previous four choices.
Select areas are also used for choosing a section from the pro gramming menu. When the programming
section name you want displays, press any select area.
DISARMED
Panic
Chime
Reset
Favorites
CURRENT
HI LO
98
98 77
LOCAL
WEATHER
CAROUSEL
MENU
INTERACTIVE
LOCK
NAVIGATION
ARROWS
POWER/ARMED
LED
STATUS
ICON
PROXIMITY
CARD READER
Figure 9: SecuraTouch™Keypad Home Screen

Digital Monitoring Products SecuraHub Installation and Programming Guide
10
PROGRAMMING INTRODUCTION
16.4 Enter Characters - Standard DMP Keypad
1. Choose a character from the table.
2. Identify the Number Key the character correlates
with and press it on the keypad.
3. Identify the Select Key or Area for that character
and press that select key or area on the keypad.
Press the select key or area again to display a
lowercase letter.
4. When the desired character displays on the
keypad, return to Step 1 to enter another
character or press CMD if nished.
16.5 Enter Characters - Alphanumeric Keypad
1. Press ABC to access uppercase letters.
2. Press abc to access lowercase letters.
3. Press !@# to access symbols.
4. Press 123 to access the number pad.
Note: Not all panel prompts accept letters and/
or symbols. For example, pressing “P” at the
“ENTER CODE” prompt will send a “6” to the
panel.
Number Key Select Key or Area
12 3 4
1A B C (
2D E F )
3G H I !
4J K L ?
5M N O /
6PQR &
7S T U @
8V W X ,
9Y Z space _
0- . * #
ABC
!@#
123
q w e r t y u i o p
a s d f g h j k l
zx c v b n m CMD
Area 4
Area 3Area 2Area 1

SecuraHub Installation and Programming Guide Digital Monitoring Products
11
FAST PROGRAMMING
Fast Programming
17.1 Fast Program
The Fast Program section allows you to quickly congure the essential settings
for the SecuraHub™ panel. When the panel programming defaults are acceptable
for installation and only basic programming options are needed, FAST PROGRAM
allows the installer to quickly enter information without navigating all of the
programming menus. After choosing FAST PROGRAM, continue through the basic list
of options.
17.2 Account Number
Enter the account num ber sent to the receiver. The range of account
numbers are 1 to 65535. For account numbers of four digits or less, you
do not have to enter leading zeros. The panel automatically right justies
the account number.
17.3 First IP Address
Enter the rst (primary) IP address and press CMD. The panel displays WPS? NO
YES. Press the fourth select area to choose YES. Press the WPS button on the
router. WIFI SETUP SEARCHING displays until connected to the IP address. Advance
to APP Key.
17.4 App Key
Enter the 8-digit App Key obtained in your Dealer Settings tab at
DMPDealerAdmin.com.
17.5 System
This congures the panel as either an All/Perimeter system (Perimeter/Interior) or
a Home/Sleep/Away system (Perimeter, Interior, and Bedrooms).
17.6 Hours from GMT
Enter the number (0-23) that indicates the Greenwich Time zone (GMT) where the
panel is located.
17.7 Weather Zip Code
Enter the zip code of the panel at this option.
17.8 Enter Siren Serial Number
Enter the eight-digit serial number for the wireless siren. The siren is automatically
set to Output 61.
17.9 Zone Number
Enter the zone number to program.
17.10 Zone Name
Press any select area to display the default zone name. To change the default zone
name, press any select area to clear name. Enter up to 16 characters for the new
zone name.
17.11 Zone Type
To change the default zone type press any select area.
17.12 Area Assignment
To change the default area, press any select area.
17.13 Serial Number Entry
Enter the eight digit serial number, including leading zeros, found on the
wireless device.
17.14 Stop
When all zones are programmed, press the Back Arrow key to display FAST
PROGRAM. Press CMD to display STOP and press any select area to exit the Fast
Program function and save the programming.
Note: All programming options are still available by reentering the
programming menu.
Note: For Full Programming options, use the full programming feature on the Tech App™ or log into the Dealer Admin
Site at DMPDealerAdmin.com.
FAST PROGRAM
ACCOUNT NO:
FIRST IP ADDR
0.0.0.0
SEARCHING
APP KEY:
SYSTEM: ALL/PERIM
AREA A/P H/A
HRS FROM GMT: 6
ENTER WEATHER
ZIP CODE: 0
ENTER SIREN
SERIAL#:-
ZONE NO: -
* DEFAULT NAME *
ZONE TYPE: -
AREA: -
SERIAL #: -
STOP

Digital Monitoring Products SecuraHub Installation and Programming Guide
12
COMPLIANCE
Listed Compliance Specications
18.1 Introduction
The programming and installation specications contained in this section must be completed when installing
the SecuraHub™ in accordance with any of the ANSI/UL or SIA burglary standards. Additional specications
may be required by a particular standard.
18.2 Use Marking
Household Burglar and Fire Control Unit.
18.2 Locations and Wiring
Locations and wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA 70 and the
Standard for Installation and Classication of Burglar and Holdup Alarm Systems, UL 681.
18.3 NFPA 72
This equipment should be installed in accordance with Chapter 29 of the National Fire Alarm Code,
ANSI/NFPA 72, (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Printed
information describing proper installation, operation, testing, maintenance, evacuation planning, and repair
service is to be provided with this equipment. Warning: Owner’s instruction notice, not to be removed by
anyone except occupant.
18.4 Types Of Service
Suitable for Household Fire and Household Burglar. Test weekly.
18.5 Police Station Phone Numbers
The SecuraHub™ must not be programmed to communicate with a police station.
18.6 Bypass Reports
The bypass reports must be programmed as YES for all listed burglary applications.
18.7 System Testing
The system must be tested once per week and Checked by a qualied technician once every three (3) years.
18.8 FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part
of your body.
This device must not be collocated or operating in conjunction with any other antenna or transmitter.

SecuraHub Installation and Programming Guide Digital Monitoring Products
13
COMPLIANCE
Household Burglar-Alarm System Units
ANSI/UL 1023
19.1 Bell Cuto
The bell cuto time cannot be less than 4 minutes.
19.2 Entry Delay
The maximum entry delay used must not be more than 45 seconds.
19.3 Exit Delay
The maximum exit delay used must not be more than 60 seconds.
19.4 Wireless External Contact
When used, the External Contact of 1101, 1102, or 1106 transmitters must be programmed Normally Closed.
19.5 Wireless Supervision Time
The Zone Information Supervision Time cannot be set to 0 (zero).
19.6 Wireless Audible Annunciation
The Wireless Audible option must be selected as DAY for residential applications.
19.7 Panel location
Mount panel inside protected area.
19.8 Test Frequency
The Test Frequency option must be programmed to send a report at least once every 30 days.
Household Fire Warning System
ANSI/UL 985 NFPA 72 Specications
20.1 Bell Output Denition
The bell output of the Model SecuraHub™ must be programmed to operate steady on burglary alarms and
temporal on re alarms.
20.2 Household System
An alarm sounding device must be installed indoors so that it is clearly heard in all sleeping areas.
20.3 Wireless Supervision Time
The Zone Information Supervision Time must be 3 minutes for re devices.
20.4 Wireless Fire Verication
When used, the Model 1161 and 1162 wireless smoke detectors must not be programmed as Fire Verication
(FV) zone type.
20.5 Battery Standby
For listed applications, the panel must have 24 Hour battery standby operation. The Model XTL+BAT3500
battery should be used for re installations.
20.6 Test Frequency
The Test Frequency option must be programmed to send a report at least once every 30 days.

Digital Monitoring Products SecuraHub Installation and Programming Guide
14
COMPLIANCE
Emergency Evacuation Plans
21.1 Overview
The National Fire Protection Association recommends that you establish an emergency evacuation plan to
safeguard lives in the event of a re or other emergency.
Draw a oor plan of your home or business
On a clean sheet of paper, draw the walls, windows, doors, and stairs. Also draw any obstacles that a person
may encounter while exiting the building such as large furniture or appliances.
Develop escape routes
Determine at least two routes the occupants in each room can take to safely escape. One route can be the
most obvious such as the door. Another can be through an easily opened window. If the window is high o
the ground, an escape ladder should be provided.
Draw arrows on the oor plan to show escape routes from each room.
Decide where to meet
Prearrange a meeting place outside and away from where emergency personnel are likely to be working. A
neighbor’s house or across the street in front of the house are good locations. Always perform a head count
to make sure all occupants safely exited. NEVER ENTER A BURNING BUILDING. If the head count shows one
or more persons missing, give this information immediately to the authorities. Never enter a building to look
for someone.
Practice your escape plans
Devising an escape plan is only the beginning. For the plan to be eective everyone should practice escape
routes from each room.
Early detection
The best way to survive a re or other emergency is to get out early. A re alarm system installation, with
smoke and carbon monoxide detectors in each room, can greatly decrease your risk of loss or injury.

SecuraHub Installation and Programming Guide Digital Monitoring Products
15
COMPLIANCE
False Alarm Reduction Programmable Options
ANSI/SIA CP-01-2010
22.1 Shipping Defaults and Recommended Programming
SIA CP-01 FEATURE
PARAGRAPH # AND
DESCRIPTION
PROGRAMMING
GUIDE SECTION # REQUIREMENT RANGE SHIPPING DEFAULT
RECOMMENDED
PROGRAMMING*
4.2.2.1 Exit Time 19.3 Exit Delay Required
(Programmable) 45 sec. - 250 sec. 60 Seconds 60 Seconds
4.2.2.3 Exit Time Restart 19.3 Exit Delay Required Option For re-entry during exit
time Enabled Enabled
4.2.4.4 Exit Time and
Progress Annunciation/
Disable - for Remote Arm
Not Available on
Remote Arming Allowed Option
Progress Annunciation
Always disabled for
Remote Arming
Not
Available
Remote Arming not
allowed for CP-01
installations.
4.2.3.1 Entry Delay(s) 19.2 Entry Delay
Required
(Programmable) Only
use Entry Delay 1. Do
not use Entry Delay 2.
30 sec. – 240 Sec. *30
Seconds
At least 30
Seconds *
4.2.5.4.1 Cancel
Annunciation
Always Enabled - Not
Programmable Required Option
Annunciate that a
Cancel was transmitted
(S49)
Always
Enabled Yes
4.2.6.1 & 4.2.6.2 Duress
Feature
User Code + 1 =
Ambush Code Not
Available
Allowed Option
No 1 + derivative of
another user code/no
duplicates with other
user codes
Code +1
Always
Disabled
Not Programmable
4.3.2 Swinger Shutdown Not Available —
Always On Required 1-6 trips 2 trips 2 trips
* For listed Installations, combined Entry Delay and Transmit Delay should not exceed 1 minute.
Local Bell
All non-re zones such as Night, Day, Exit, Aux 1 and Aux 2 must be programmed for local bell enabled with a bell
cuto time set to a minimum of 6 minutes to provide a cancel window of 5 minutes or greater. This does not apply
to manually operated zone types such as Panic and Emergency.
The requirements are superseded by any requirements for Commercial Burglar, Household Fire Warning, or
Household Burglar applications.
Minimum Installation Requirements: SIA CP-01-2010 minimum system installation requirements include a
SecuraHub™, a SecuraSounder, a SecuraTouch keypad, and communication to an SCS-1R receiver.

Digital Monitoring Products SecuraHub Installation and Programming Guide
16
REVISIONS
Revisions to This Document
This section explains the changes made to this document during this revision. It lists the date and identies
the change(s) made, the related section number and section heading, and a summary of the change.
Ver. Section Number and Heading Quick Explanation of Changes
1.01 Entire Document Initial Release