DOGA GX-G Series User manual

Instructions manual / GX-G Screwdrivers
1
GX-G Screwdrivers
GXA-G Screwdrivers
(40 Volts)
INSTRUCTIONS MANUAL
INSTRUCTIONS MANUAL

Instructions manual / GX-G Screwdrivers
2
IMPORTANT
The tool delivered with this manual may have been modified for specific needs.
In that case, please give us the tool code number written on our shipping note or the approximate tool delivery
date when you place an order for a new similar tool or for spare parts.
In that way, you will be sure to get the required tool and/or spare part.
WARNING
This information has to be kept in a location know by all users.
Each operator has to read carefully this manual before installing, using, and
mending the product.
Be sure that the operator has understood using recommendations and the meaning of signs put on the product.
Most accidents could be avoided respecting this Manual Instructions. As a matter of fact, they were created
according to European laws and norms regarding products.
In each case, please respect and follow safety national norms. Do not take off nor damage the stickers or advise
put on the product and above all the details imposed by the law.

Instructions manual / GX-G Screwdrivers
3
SUMMARY
1. GENERAL SAFETY RULES................................................................................................... 4
2. SPECIFIC SAFETY RULES.................................................................................................... 5
3. Electric specification............................................................................................................. 6
4. Mechanical specification of XS-40D..................................................................................... 6
5. Input Power select................................................................................................................. 6
6. Screwdriver Specification..................................................................................................... 7
7. Torque curve (No load - Max. speed).................................................................................... 8
8. Panel of each model.............................................................................................................. 8
9. Alarm display by LED............................................................................................................ 8
10. Operation ............................................................................................................................... 9
10.1 Speed & Soft Start setting ( GX___ -G) ( GXA___ -G)...........................................................................9
10.2 Speed/Angle control & Auto reverse ( GXT__ -G)...............................................................................10
11. Change Notification of T Option - run and torque up signals........................................... 14
12. Exploded views and part list............................................................................................... 15
12.1 GX150-G and GX220-G ..........................................................................................................................15
12.2 GX450-G..................................................................................................................................................18
12.3 GX150P-G and GX220P-G......................................................................................................................21
12.4 GX450P-G................................................................................................................................................24
12.5 GXA150-G and GXA220-G .....................................................................................................................26
12.6 GXA450-G................................................................................................................................................29
13. Exploded views and part list for tools with minimum SN 1701080036 ............................ 32
13.1 GX150-G and GX220-G ..........................................................................................................................32
13.2 GX450-G..................................................................................................................................................35
13.3 GX150P-G and GX220P-G......................................................................................................................38
13.4 GX450P-G................................................................................................................................................41
13.5 GXA150-G and GXA220-G .....................................................................................................................43
13.6 GXA450-G................................................................................................................................................46

Instructions manual / GX-G Screwdrivers
4
1. GENERAL SAFETY RULES
WARNING! Read and understand all instructions. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious personal injury
SAVE THESE INSTRUCTIONS
1.1 Work Area
- Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep bystanders, children, and visitors away while operating a power tool. Distractions can
cause you to lose control.
1.2 Electrical Safety
- Grounded tools must be plugged into an outlet properly installed and grounded in accordance
with all codes and ordinances. Never remove the grounding prong or modify the plug in any
way. Do not use any plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
- Avoid body contact with grounded surface ad pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is grounded.
- Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock
- Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
- When operating a power tool outside, use an outdoor extension cord marked W-A or W.
These cords are rated for outdoor use and reduce the risk of electric shock.
1.3 Personal Safety
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of
inflation while operating power tools may result in serious personal injury.
- Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in
moving parts.
- Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger
on the switch or plugging in tools may result in personal injury.
- Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations.
- Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat,
or hearing protection must be used for appropriate conditions.
1.4 Tool use and Care
- Use clamps or other practical way to secure and support the workplace to a stable platform.
Holding the work by hand or against your body is unstable and may lead to loss of control.
- Do not force tool. Use the correct tool for your application. The correct tool will do the job better
and safer at the rate for which it is designed.
- Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
- Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventive safety

Instructions manual / GX-G Screwdrivers
5
- Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the
hands of untrained users.
-Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to control.
- Check for misalignment or binding of moving parts, breakage of parts, and any other condition
that may affect the tools operation. If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
- Use only accessories that are recommended by the manufacturer for your model. Accessories
that may be suitable for one tool, may become hazardous when used on another tool.
1.5 SERVICE
- Tool service must be performed only by qualified personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury
- When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance
instructions may create a risk of electric shock or injury.
2. SPECIFIC SAFETY RULES
2.1 Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
2.2 Never lubricate aerosol oil on to the electrical part.

Instructions manual / GX-G Screwdrivers
6
3. Electric specification
Items
Power controller
Screwdriver
Model
XS-40D
GX150-G, GX220-G, GX450-G,
GX150P-G, GX220P-G,
GX450P-G
Input
110 / 230VAC (selectable)
DC40V
Output
30/40VDC ( selectable )
Rated power
2.5A 95W
Maximum output current
8 A
Intermittent operation
10s On / 30s Off
Safety system
CE certified ( Class I )
Class III
4. Mechanical specification of XS-40D
Size: 98 x 158 x 55H (mm)
Weight: 850gr
Power cord: 1.5 m
Fuse: 10 A 250V
5. Input Power select
By replacing the position of cover as below, the input power can be selected for 110V or 230V.

Instructions manual / GX-G Screwdrivers
7
6. Screwdriver Specification
■ Specification
Model
Start
Torque
Rotation
Speed
Options
Clutch**
Software*
(Kgf.cm)
(Rpm)
Standard
Soft Stop
Standard
T
GX 150/ESD-G
LEVER
3~15
800~1700
○
○
GX 220/ESD-G
6~22
600~1200
○
○
GX 450/ESD-G
10~45
300~600
○
○
GX 150P/ESD-G
PUSH
3~15
800~1700
○
○
GX 220P/ESD-G
6~22
600~1200
○
○
GX 450P/ESD-G
10~45
300~600
○
○
GXS 150/ESD-G
LEVER
3~15
800~1700
○
○
GXS 220/ESD-G
6~22
600~1200
○
○
GXT 150/ESD-G
LEVER
3~15
800~1700
○
○
GXT 220/ESD-G
6~22
600~1200
○
○
GXT 450/ESD-G
10~45
300~600
○
○
GXA 150/ESD-G
REMOTE
3~15
800~1700
○
○
GXA 220/ESD-G
6~22
600~1200
○
○
GXA 450/ESD-G
10~45
300~600
○
○
* Software :
- Standard = Speed Control + Soft Start (soft start not available on GXA models)
- T = Speed & Angle Control + Auto Reverse
** Clutch :
- Clutch mechanism is symmetric (torque is equal in forward and reverse modes) on GX_450-G
models and asymmetric on GX_150-G and GX_220-G models.

Instructions manual / GX-G Screwdrivers
8
7. Torque curve (No load - Max. speed)
GX 150 : Silver spring, dia 2,3 mm
GX 220 : Gold spring, dia 2,5 mm
GX 450 : Bronze spring , dia 2,2 mm
Changing springs :
1 - Loosen completely the torque adjusting ring.
2 - Take off the torque spring you do not want to use anymore.
3 - Put in the torque spring you want to use.
4 - Put back the torque adjusting ring.
5 - Do not forget to adjust the torque ring to the target torque.
8. Panel of each model
Standard (Speed control & Soft Start) Speed & Angle control & Auto reverse
GX__-G GXT___-G
9. Alarm display by LED
no
Alarm
Description
Reset
1
Over Voltage (over 44V)
●●↔●● Green & Red lights blinks
Auto reset under 44V
2
Overload (4A/0.5s)
●● Two Red lights blinks.
Auto reset after 5s
3
Overheat(over 80℃_motor)
●● Two Orange light blinks
Auto reset lower than 80℃
4
Driver Lock by ext. signal
●● Two Green lights blinks
Auto reset by signal off

Instructions manual / GX-G Screwdrivers
9
10.Operation
10.1 Speed & Soft Start setting ( GX___ -G) ( GXA___ -G)
Speed Selection:
1) Press the Speed button for 2 seconds to visit to
PROGRAM mode. Then the two LED lights will
display colours depending on the set speed.
2) Select "Reverse" on F/R switch for increasing
speed or select "Forward" on F/R switch for
increasing speed.
3) Press the Speed button and select the target
speed.
The set speed can be recognized by the colors of
two LED as below.
4) Press the Speed button for 2 seconds to go
back to operating (work) mode.
■Speed display by two LED color (Standard model)
Model
LED
● ●
●●
●●
●●
●●
●●
●●
●●
●●
Button
1th
2nd
3rd
4th
5th
6th
7th
8th
9th
GX150-G
RPM
800
900
1000
1100
1200
1300
1400
1500
1700
GX220-G
RPM
600
650
700
750
800
900
1000
1100
1200
GX450-G
RPM
300
340
380
410
450
490
530
560
600
GXA150-G
RPM
800
900
1000
1100
1200
1300
1400
1500
1700
GXA220-G
RPM
600
650
700
750
800
900
1000
1100
1200
GXA450-G
RPM
300
340
380
410
450
490
530
560
600
Soft Start Setting:
1) Press the Soft Start button for 2 seconds to enter setting mode.
2) Press the Soft Start button (pulse) to increase the Soft Start duration. As shown below, 3 steps are
available.
3) Press the Soft Start button for 2 seconds to save.
●Green: 0.2 second
●Red: 0.4 second
●Orange: 0.6 second

Instructions manual / GX-G Screwdrivers
10
10.2 Speed/Angle control & Auto reverse ( GXT__ -G)
Model: GXT150-G, GXT220-G, GXT450-G
One triggering by the lever can make 3 steps operation sequence in a cycle
■Start, Stop and Direction in a cycle
Step
1
→
2
→
3
Sequence
first RUN
stop HOLD
reverse RUN
Rotating
direction
Clockwise or
Counterclockwise by
F/R switch
Reverse
Activating
Screwdriver run to the
target angle and stops. It
always stops at the set
torque, even it does not
reach the target angle.
delay for
set time
Screwdriver run reverse to
the target angle and stops.
It always stops at the set
torque, even it does not
reach the target angle.
Angle run &
Time delay
29 steps
1/4 to 30 turns
14 steps
0.2 to 3 sec
29 steps
1/4 to 30 turns
- Screwdriver stops Immediately when the lever is released in any sequence.
- Sliding F/R switch works for increasing or decreasing of setting
■Operating (Work) mode
①Rotating direction (FOR-REV)
■PROGRAM mode
①First run angle (Increase / Decrease) together with "First Run(Speed)" button
②Time (Increase / Decrease) together with "Stop(Reverse)" button
③Rotation speed (Increase / Decrease) together with "Speed(First Run)" button
④Reverse run angle (Increase / Decrease) together with "Reverse(Stop)" button

Instructions manual / GX-G Screwdrivers
11
■Angle setting for first RUN
①Keep the first Run button pressed over 2 sec. for angle setting. Then press one by one for the
desired rotating angle
②Select the R position of F/R switch for increasing set angle or F position for decreasing set angle
③Keep the first Run button pressed over 2 sec. for Lock & operating mode.
■Time setting for stop HOLD
①Keep the stop time button pressed over 2 sec. Then click the stop time button one by one for
desired stop holding time
②Select the R position of F/R switch for increasing set time or F position for decreasing set time
③Keep the stop time button pressed over 2 sec. for Lock & operating mode.

Instructions manual / GX-G Screwdrivers
12
■Rotating speed setting
①Keep both first Run & stop time buttons pressed over 2 sec. to unlock. Then click one by one for
the desired rotating speed.
②Select the R position of F/R switch for increasing speed or F position for decreasing speed
③Keep the first Run button pressed over 2 sec. to Lock & operating mode.
Model
LED
● ●
●●
●●
●●
●●
●●
●●
●●
●●
Button
1th
2nd
3rd
4th
5th
6th
7th
8th
9th
GX150-G
RPM
800
900
1000
1100
1200
1300
1400
1500
1700
GX220-G
RPM
600
650
700
750
800
900
1000
1100
1200
GX450-G
RPM
300
340
380
410
450
490
530
560
600
GXA150-G
RPM
800
900
1000
1100
1200
1300
1400
1500
1700
GXA220-G
RPM
600
650
700
750
800
900
1000
1100
1200
GXA450-G
RPM
300
340
380
410
450
490
530
560
600
■Angle setting for Reverse RUN
①Keep both first Run & stop time buttons pressed over 2 sec. to unlock. Then click stop time button
one by one for the desired angle
②Select the R position of F/R switch for increasing set angle or F position for decreasing set angle
③Keep the stop time button pressed over 2 sec. to Lock & operating mode.

Instructions manual / GX-G Screwdrivers
13
■Application Example
First
RUN
Angle
Stop
HOLD
Time
Auto
Reverse
Angle
Applications with different
sequence in a cycle
Normal
screwdriver
off
off
off
Normal screwdriver
It stops at the set torque
Angle
control
ON(1)
off
off
It stops at set angle(1)
Tapper or
Insert
fastening
ON(1)
ON(2)
ON(3)
or
off
It stops at set angle(1) and waits
for set time(2), and makes reverse
rotation to the set angle(3)
Wire
inserting on
terminal
block
ON(1)
ON(2)
off
It stops at set angle(1) and waits
for set time(2), and makes reverse
rotation and stops at set torque

Instructions manual / GX-G Screwdrivers
14
11.Change Notification of T Option - run and torque up signals
Effective from GXT, S/N: 1805060073 and GXT-G, S/N: 1805080168.
Applicable to GXT 30V and GXT-G 40V Electric Screwdrivers
Concerns feature of out signals : run and torque up
If the
user set 1st run-stop-reverse turn as a complete cycle, motor run signal will last for a cycle.
In the same way, if just 1st run is set, motor run signal comes out just once.
2) One Torque-up Count for One Complete T Cycle with SCOUTII
1st and 2nd run are either torque or angle control
Torque up signal means complete cycle Ok
Applied Version : F_Standard_Driver_V1.5.1_Firmware(GXT***)_DCN180524/
F_Standard_Driver_V1.5.1_Firmware(GXT***-G)_DCN180524
Motor run
Torque up
1st run 2nd run
Motor run
Torque up
* if set
one cycle
hold
one cycle
1st run + hold* + 2nd run*
1)
Complete Motor Run Signal Out During One Cycle

Instructions manual / GX-G Screwdrivers
15
12.Exploded views and part list
12.1 GX150-G and GX220-G
•Exploded view

Instructions manual / GX-G Screwdrivers
16
•Part list
NO.
CODE
REF
DESCRIPTION
GX150-G
GX220-
G
1
1070300
505-0002
ADJUSTER
1
1
2
1070301
557-0003
PIN [ADJUST]
4
4
3
1070335
581-0065
SPRING [TORQUE]
1
3
1070336
581-0067
SPRING [TORQUE]
1
4
1075080
515-0008
WRENCH BOLT
4
4
5
1070303
316-0024
COVER ASSY [TOP]
1
1
6
1075005
527-0017
C-RING [BIT SOCKET]
1
1
7
1070304
524-0003
COLLAR
1
1
8
1070305
581-0025
SPRING [COLLAR]
1
1
9
1070306
514-0010
BIT SOCKET [A]
1
1
10
1075014
507-0003
BALL
2
2
11
1077135
557-0017
PIN [GEAR HOLDER ]
1
1
12
1075018
527-0006
C-RING
1
1
13
1070309
538-0002
GUIDE [NEEDLE PIN]
1
1
14
1070310
590-0032
WASHER [BEND]
1
1
15
1002867
509-0035
BEARING [THRUST]
1
1
16
1002754
509-0028
BEARING [OILLESS]
2
2
17
1002701
349-0001
SLIDE BAR ASSY
1
1
18
1002749
581-0043
SPRING [LIMIT]
1
1
19
1075114
571-0012
SCREW
2
2
20
1077673
346-0007
SENSOR ASSY [LEVER]
1
1
21
1070338
557-0028
PIN [NEEDLE]
3
3
22
1077674
304-0008
BEARING COVER ASSY [LEVER]
1
1
23
1002860
569-0011
RING [SLIDE]
1
1
24
1002750
573-0001
SHAFT [LEVER]
1
1
25
1075106
507-0005
BALL
2
2
26
1002708
311-0017
CLUTCH ASSY
1
26
1077680
311-0019
CLUTCH ASSY
1
27
1002796
536-0046
GEAR [CASE]
1
27
1002842
536-0048
GEAR [CASE]
1
28
1075008
515-0009
WRENCH BOLT
2
2
29
1002835
571-0001
SCREW [FL TORX]
5
5
30
1002751
536-0028
GEAR [2ND IDLE]
4
30
1075118
536-0024
GEAR [2ND IDLE B]
4
31
1002751
536-0028
GEAR [2ND IDLE]
4
31
1002758
536-0018
GEAR [1ST IDLE]
3
32
1002850
325-0009
HOLDER ASSY [GEAR]
1
32
1075123
325-0012
HOLDER ASSY [GEAR]
1
33
1002857
557-0007
PIN [CENTER]
1
1
34
1002858
590-0005
WASHER
1
1
35
1075125
578-0004
SNAP RING
1
1
36
1070347
515-0012
WRENCH BOLT
3
3
37
1077551
532-0023
FLANGE
1
1
38
1002853
536-0094
GEAR [PINION]
1
38
1075127
536-0088
GEAR [PINION B]
1
39
1070139
551-0010
BLDC MOTOR
1
1
40
1070339
544-0020
HOUSING NUT
1
1
41
1002753
571-0016
SCREW
2
2
42
1012467
542-0031
HOUSING [UPPER]
1
1
43
1012406
327-0005
HOUSING ASSY [LOWER]
1
1
44
1070143
541-0003
HOOK
1
1
45
1002705
329-0014
LEVER ASSY
1
1
46
1002855
581-0037
SPRING [LEVER]
1
1
47
1077172
571-0025
SCREW
3
3
48
1012329
316-0012
COVER ASSY [SWITCH]
1
1
49
1070145
539-0005
HEAT SINK
1
1
50
1002759
903-0067
THERMAL SILICONE PAD
1
1
51
1077684
331-0012
AMP PCB ASSY [SET]
1
1
52
1070147
332-0062
CONTROL PCB ASSY [SET]
1
1
53
1002843
582-0016
SUPPORTER [PCB]
2
2
54
1002861
555-0001
NUT
1
1
55
1002878
590-0021
WASHER
1
1
56
1070148
520-0005
CAP
2
2
57
1012345
526-0020
COVER [CONNECTOR LOCK]
1
1
58
1078885
555-0002
NUT
1
1
60
1070151
548-0114
LABEL [WINDOW]
1
1
60
1070153
548-0116
LABEL [WINDOW]
1
1
61
1070316
582-0035
SUPPORTER [TORQUE SPRING
WASHER]
1
1
62
1070317
582-0037
SUPPORTER [TORQUE SPRING]
1
1
63
1070318
509-0022
BEARING [BALL]
1
1

Instructions manual / GX-G Screwdrivers
17
64
1070319
579-0013
SNAP RING
1
1
65
1070320
510-0001
BEARING HOLDER
1
1
66
1070321
527-0023
C-RING [STOP]
1
1
67
1002864
557-0032
PIN [NEEDLE]
1
1
KIT
6~12
1070230
307-0034
BIT SOCKET ASSY
1
1
16(2),22~24
1070228
304-0029
BEARING COVER + SHAFT ASSY
1
1
26~35
1070231
901-0011
GEAR BOX
1
26~35
1070235
901-0012
GEAR BOX
1
42,43
1076002
903-0048
NF HOUSING SET
1
1
51,52
1012530
903-0177
PCB SET
1
1
1~16,21~24,40,66
1081400
901-0061
DOUBLE BEARING UPGRADE KIT
1
1~16,21~24,40,66
1035000
901-0073
DOUBLE BEARING UPGRADE KIT
1

Instructions manual / GX-G Screwdrivers
18
12.2 GX450-G
•Exploded view

Instructions manual / GX-G Screwdrivers
19
•Part list
NO.
CODE
REF
DESCRIPTION
GX450-G
1
1070300
505-0002
ADJUSTER
1
2
1070301
557-0003
PIN [ADJUST]
4
3
1070302
581-0069
SPRING [TORQUE]
1
4
1075008
515-0009
WRENCH BOLT
4
5
1070303
316-0024
COVER ASSY [TOP]
1
6
1075005
527-0017
C-RING [BIT SOCKET]
1
7
1070304
524-0003
COLLAR
1
8
1070305
581-0025
SPRING [COLLAR]
1
9
1070306
514-0010
BIT SOCKET [A]
1
10
1075014
507-0003
BALL
2
11
1077135
557-0017
PIN [GEAR HOLDER ]
1
12
1075018
527-0006
C-RING
1
13
1070309
538-0002
GUIDE [NEEDLE PIN]
1
14
1070310
590-0032
WASHER [BEND]
1
15
1002867
509-0035
BEARING [THRUST]
1
16
1002754
509-0028
BEARING [OILLESS]
1
17
1002701
349-0001
SLIDE BAR ASSY
1
18
1002749
581-0043
SPRING [LIMIT]
1
19
1075114
571-0012
SCREW
2
20
1077673
346-0007
SENSOR ASSY [LEVER]
1
21
1070311
557-0029
PIN [NEEDLE]
3
22
1077510
304-0014
BEARING COVER ASSY [LEVER]
1
23
1002761
582-0002
SUPPORTER [BEARING]
1
24
1002783
509-0001
BEARING [BALL]
1
25
1002784
509-0002
BEARING [BALL]
1
26
1075103
569-0010
RING [SLIDE]
1
27
1070188
573-0003
SHAFT [LEVER]
1
28
1070206
507-0004
BALL
3
29
1070313
311-0016
CLUTCH ASSY
1
30
1055332
536-0058
GEAR [CASE]
1
31
1002835
571-0001
SCREW [FL TORX]
4
32
1055333
536-0039
GEAR [3RD IDLE]
3
33
1002864
557-0032
PIN [NEEDLE]
1
34
1055334
325-0016
HOLDER ASSY [GEAR]
1
35
1055335
536-0009
GEAR [IDLE]
6
36
1002707
325-0007
HOLDER ASSY [GEAR]
1
37
1002858
590-0005
WASHER
1
38
1075125
578-0004
SNAP RING
1
39
1070347
515-0012
WRENCH BOLT
3
40
1077551
532-0023
FLANGE
1
41
1002745
536-0075
GEAR [MOTOR PINION]
1
42
1070314
544-0022
HOUSING NUT
1
43
1002752
515-0003
WRENCH BOLT
2
44
1012467
542-0031
HOUSING [UPPER]
1
45
1012406
327-0005
HOUSING ASSY [LOWER]
1
46
1077172
571-0025
SCREW
3
47
1070143
541-0003
HOOK
1
48
1002705
329-0014
LEVER ASSY
1
49
1002855
581-0037
SPRING [LEVER]
1
50
1002864
557-0032
PIN [NEEDLE]
1
51
1012329
316-0012
COVER ASSY [SWITCH]
1
52
1070145
539-0005
HEAT SINK
1
53
1002759
903-0067
THERMAL SILICONE PAD
1
54
1002843
582-0016
SUPPORTER [PCB]
2
55
1070148
520-0005
CAP
2
56
1002878
590-0021
WASHER
2
57
1002861
555-0001
NUT
2
58
1070139
551-0010
BLDC MOTOR
1
59
1070147
332-0062
CONTROL PCB ASSY [SET]
1
60
1077684
331-0012
AMP PCB ASSY [SET]
1
61
1077695
330-0038
MOTOR ASSY [SET]
1
63
1070151
548-0114
LABEL [WINDOW]
1
63
1070153
548-0116
LABEL [WINDOW]
1
64
1070316
582-0035
SUPPORTER [TORQUE SPRING WASHER]
1
65
1070317
582-0037
SUPPORTER [TORQUE SPRING]
1
66
1070318
509-0022
BEARING [BALL]
1
67
1070319
579-0013
SNAP RING
1
68
1070320
510-0001
BEARING HOLDER
1
69
1070321
527-0023
C-RING [STOP]
1
70
1070322
547-0003
KEY
2
71
1070323
515-0024
WRENCH BOLT
2
KIT

Instructions manual / GX-G Screwdrivers
20
6~12
1070230
307-0034
BIT SOCKET ASSY
1
16 ,22,26,27
1070221
304-0031
BEARING COVER + SHAFT ASSY
1
29~38
1070236
901-0013
GEAR BOX
1
44,45
1076002
903-0048
NF HOUSING SET
1
59,60
1012530
903-0177
PCB SET
1
1~16,21~31,42
1081402
901-0063
DOUBLE BEARING UPGRADE KIT
1