Dometic 620526.336 User manual

620515, 620525, 620526, 630515 & 630516 Installation Instructions
1
Important:TheseInstructions
must stay with unit.
Owner read carefully.
REVISION:
FormNo.3309083.0162/05
(Replaces3309083.008)
(French3309084.014)
©2005DometicCorporation
LaGrange,IN 46761
USA
SERVICEOFFICE
DometicCorporation
2320IndustrialParkway
Elkhart,IN46515
574-294-2511
CANADA
DometicDistribution
866LangsDrive
Cambridge,Ontario
CANADAN3H2N7
519-653-4390
For Service Center
AssistanceCall:
800-544-4881
C
U
S
INSTALLATION
INSTRUCTIONS
Models
620515.331
620515.336
620525.331
620525.336
620526.331
620526.336
630515.331
630515.336
630516.331
630516.336
RECORDTHISUNITINFORMATIONFOR
FUTUREREFERENCE:
Model Number
Serial Number
Date Purchased
MODEL
620515, 620525, 620526
Roof-Top Air Conditioner
630515, 630516
Roof Top Heat Pump
THIS UNIT IS DESIGNED FOR OEM INSTALLATION
ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE SALES DEPT.
used with one of following:
3105007 Return Air Cover
3105935 Quick Cool Return Air Cover
3308120 Genesis Air Filtration System
and
3109228.001 Comfort Control CenterTM
This manual must be read and un-
derstood before installation, ad-
justment, service, or maintenance
is performed. This unit must be in-
stalled by a qualified service tech-
nician.Modificationofthisproduct
can be extremely hazardous and
could result in personal injury or
property damage.
Lire et comprendre ce manuel avant de
procéderàl'installation,àdesréglages,
de l'entretien ou des réparations.
L'installation de cet appareil doit être
effectuée par un réparateur qualifié.
Toute modification de cet appareil peut
être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.

620515, 620525, 620526, 630515 & 630516 Installation Instructions
2
SAFETY INSTRUCTIONS
This manual has safety information and instruc-
tionsto helpusers eliminateor reducethe riskof
accidentsand injuries.
RECOGNIZE SAFETY INFORMATION
Thisisthesafety-alertsymbol.Whenyou see this
symbolinthis manual,bealert tothepotentialfor
personalinjury.
Follow recommended precautions and safe op-
eratinginstructions.
UNDERSTAND SIGNAL WORDS
Asignal word ,WARNING OR CAUTION isused
withthesafety-alertsymbol.Theygivethelevelof
riskforpotentialinjury.
indicates a potentiallyhazard-
oussituation which, ifnotavoided, couldresultin
deathorseriousinjury.
indicates a potentially hazard-
ous situation which, if not avoided may result in
minorormoderate injury.
used without the safety alert
symbol indicates, a potentially hazardous situa-
tion which, if not avoided may result in property
damage.
Readandfollowallsafetyinformationandinstruc-
tions.
!
WARNING
!
CAUTION
CAUTION
!
A. Productfeaturesorspecificationsasdescribedorillus-
trated are subject to change without notice.
B. This Air Conditioner Is Designed For:
1. Installationonarecreationalvehicleduringthetime
thevehicleismanufactured.
2. Mountingontheroofofarecreationalvehicle.
3. Roofconstructionwithrafters/joistsonminimumof
16 inch centers.
4. Minimum of 2.00 inches and maximum of 5.50
inches distance between roof to ceiling of recre-
ational vehicle. Alternate installation methods will
allowforroofs more than 5.50 inches thick.
C. Theabilityoftheairconditionertomaintainthedesired
insidetemperaturedependsontheheatgainoftheRV.
Somepreventativemeasurestakenbytheoccupantsof
the RV can reduce the heat gain and improve the
performance of the air conditioner. During extremely
highoutdoortemperatures,theheatgainofthevehicle
may be reduced by:
1. Parking the RV in a shaded area
2. Usingwindowshades(blindsand/orcurtains)
3. Keepingwindowsanddoors shut or minimizingus
age
4. Avoidingtheuseofheatproducingappliances
Operation on High Fan/Cooling mode will give optimum or
maximum efficiency in high humidity or high outside tem-
peratures.
Startingtheairconditionerearlyinthemorningandgivingit
a "head start" on the expected high outdoor ambient will
greatly improve its ability to maintain the desired indoor
temperature.
Foramore permanent solution tohighheat gain, accesso-
rieslikeA&Eoutdoorpatioandwindowawningswillreduce
heat gain by removing the direct sun. They also add a nice
areatoenjoycompanyduring the cool of the evening.
D. Condensation
Note: The manufacturer of this air conditioner will not be
responsiblefordamagecausedbycondensedmoistureon
ceilings or other surfaces. Air contains moisture and this
moisture tends to condense on cold surfaces. When air
enters the RV, condensed moisture may appear on the
ceiling, windows, metal parts, etc. The air conditioner re-
moves this moisture from the air during normal operation.
Keepingdoorsandwindowsclosedwhenthisairconditioner
is in operation will minimize condensed moisture on cold
surfaces.
GENERAL INFORMATION

620515, 620525, 620526, 630515 & 630516 Installation Instructions
3
620515.331 13,500 1530 12.4 60.0 3.5 10.0 335/250 .012/0.65 16.5 20Amp 95 3.5KW/5.0KW
620515.336 13,500 1530 12.4 60.0 3.5 10.0 335/250 .012/0.65 16.5 20Amp 95 3.5KW/5.0KW
620525.331 13,500 1530 12.4 60.0 3.5 10.0 335/250 .012/0.65 16.5 20Amp 95 3.5KW/5.0KW
620525.336 13,500 12.4 60.0 3.5 10.0 335/250 .012/0.65 16.5 20 Amp 95 3.5KW/5.0KW
620526.331 15,000 12.0 64.0 3.3 8.2 380/250 .012/0.65 20.0 20Amp 95 3.5KW/5.0KW
620526.336 15,000 12.0 64.0 3.3 8.2 380/250 .012/0.65 20.0 20Amp 95 3.5KW/5.0KW
630515.331 13,500 12.4 60.0 3.5 10.0 335/250 .012/0.65 23.5 20 Amp 95 3.5KW/5.0KW
630515.336 13,500 12.4 60.0 3.5 10.0 335/250 .012/0.65 23.5 20 Amp 95 3.5KW/5.0KW
630516.331 15,000 12.0 64.0 3.3 8.5 335/250 .012/0.65 20.0 20Amp 95 3.5KW/5.0KW
630516.336 15,000 12.0 64.0 3.3 8.5 335/250 .012/0.65 20.0 20Amp 95 3.5KW/5.0KW
SPECIFICATIONS
* For wire length over 24 ft., consult the National Electric Code for proper sizing. ** DometicCorporationgivesGENERALguidelinesforgenerator requirements.Theseguidelinescomefromexperiencespeoplehavehadinactualapplications.
When sizing the generator, the total power usage of your recreational vehicle must be considered. Keep in mind generators lose power at high altitudes and fromlackofmaintenance.
*** CIRCUITPROTECTION:TimeDelayFuseorHACRCircuitBreakersRequired.
Model
No. Nominal
Capacity
(BTU/HR)
Cooling
Electrical
Rating
Amps
Heater
Watts Compressor
Rated
Load
Amps
Compressor
Locked
Rotor
Amps
Fan Motor
Locked
Rotor
Amps
Fan Motor
Rated
Load
Amps
SCFM-High
Speed
Max./Min.
W.C.
Total
Static
Max./Min.
Refrigerant
R-22
(Oz.)
Minimum
Wire Size* AC Circuit
Protection
** User
Supplied
Installed
Weight
(Pounds)
Minimun
Generator
Size**
1Unit/2Units
120VAC
60Hz.
1Phase
12AWG
Copper
Up To 24'

620515, 620525, 620526, 630515 & 630516 Installation Instructions
4
A. Precautions
Improperinstallationmaydamage equipment,
could endanger life, cause serious injury and/
or property damage.
1. ReadInstallation and Operating Instructions care-
fully before attempting to start your air conditioner
installation.
2. DometicCorporationwillnotbeliableforanydam-
ages or injury incurred due to failure in following
these instructions.
3. InstallationmustcomplywiththeNationalElectrical
Code ANSI/NFPA-70 and CSA Standard C22.1
(latest edition and any State or Local Codes or
regulations.
4. DONOT addanydevicesoraccessoriestothisair
conditionerexceptthosespecificallyauthorizedby
Dometic.
5. This equipment must be serviced by qualified per-
sonnelandsomestatesrequirethesepeopletobe
licensed.
B. Choosing Proper Location For The Air
Conditioner
Thisairconditionerisspecificallydesignedforinstallationon
theroofofarecreationalvehicle(RV).Whendeterminingyour
coolingrequirements,thefollowingshouldbeconsidered:
•Size of RV;
•Windowarea(increasesheatgain);
•Amountof insulation inwalls and roof;
•GeographicallocationwheretheRVwillbeused;
•Personalcomfortlevelrequired.
1. NormalLocation-Theairconditionerisdesignedto
fitoveranexistingroofventopening.
INSTALLATION INSTRUCTIONS
2. Other Locations-When no roof vent is available or
anotherlocationisdesired,thefollowingis recom-
mended:
a. For one unit installation: The air conditioner
should be mounted slightly forward of center
(front to back) and centered from side to side.
b. Fortwounitinstallations:InstalloneAirCondi-
tioner 1/3 and one Air Conditioner 2/3’s from
front of RV and centered from side to side.
Itispreferredthattheairconditionerbeinstalledon
a relatively flat and level roof section measured
withthe RV parkedon a levelsurface.
Note:A8°slanttoeitherside,orfronttoback,isacceptable
for all units.
3. AfterLocation Has Been Selected:
a. Check for obstructions in the area where air
conditioner will be installed. See FIG. 4.
b. The roof must be designed to support 130
pounds when the RV is in motion. Normally a
200lb.staticloaddesignwillmeetthisrequire-
ment.
CAUTION
It is the responsibility of the installer of this
air conditioner system to ensure structural in-
tegrity of the RV roof. Never create a low spot
on the roof where water will collect. Water
standing around the air conditioner may leak
into the interior causing damage to the prod-
uct and the RV.
c. Check inside the RV for return air kit obstruc-
tions (i.e. door openings, room dividers, cur-
tains, ceiling fixtures, etc.) See FIG. 3 & 4.
FIG. 1
1/2L LL
1/3L
2/3L
FIG. 2
FIG. 3
Micro-ThermFilterSystem
Micro-ThermFilter System
FILTER
RESET
FILTER
RESET
CLEAN
FILTER
CLEAN
FILTER
9-1/2"
39"
28-3/4"
17"
17"
2"
3/4"
18-1/2"
20-7/8"
Genesis
Standard
Grill

620515, 620525, 620526, 630515 & 630516 Installation Instructions
5
It is the responsibility of the installer of this
air conditioner system to ensure structural
integrity of the RV roof. Never create a low
spot on the roof where water will collect. Wa-
ter standing around the air conditioner may
leak into the interior causing damage to the
product and the RV.
CAUTION
C. Roof Preparation
1. OpeningRequirements-Beforepreparingtheceil-
ing opening, the type of system options must be
decidedupon.Readallofthefollowinginstructions
beforebeginningtheinstallation.
Ifaroofventopeningwillnotbeuseda14-1/4"x14-
1/4"(±1/8")openingmustbecutthroughtheroofand
ceiling of the RV. This opening must be located
betweentheroofreinforcingmembers.
The14-1/4"x14-1/4"(±1/8")openingispart of the
returnairsystemoftheAirConditionerandmustbe
finished in accordance with NFPA Standard 501C
Section 2.7.2.
2. RoofVentRemoval
a. Unscrewandremovetheroofvent.
b. Remove all caulking compound around open-
ing.
c. Sealallscrewholesandseamswheretheroof
gasket is located. Use a good grade of all
weathersealant. See FIG.5.
d. Ifthe openingexceeds14-3/8"x14-3/8", itwill
benecessary tore-sizetheopeningto14-1/4"
x14-1/4" (±1/8").
e. If the opening is less than 14-1/8" x 14-1/8", it
mustbeenlarged.
3. NewOpening-(InstallationOtherThanVentOpen-
ing)
a. Marka14-1/4"x14-1/4"(±1/8")square on the
roofand carefullycuttheopening.
b. Using the roof opening as a guide, cut the
matching hole in the ceiling.
c. Theopeningcreatedmustbeframedtoprovide
adequate support and prevent air from being
drawnfromtheroofcavity.Lumber3/4"ormore
in thickness must be used. Remember to pro-
vide an entrance hole for power supplies, fur-
nacewiringandaseven-conductorcable,18to
22 AWG is to be used for analog thermostat
connections.
There may be electrical wiring between the
roof and the ceiling. Disconnect 120 volt AC
power cord and the positive (+) 12 volt DC ter-
minal at the supply battery. Failure to follow
this instruction may create a shock hazard
causing death or severe personal injury.
FIG. 4
14-1/4" x 14-1/4”
(±1/8”) OPENING
21-3/8”
KEEP THESE AREAS
FREE OF OBSTRUCTIONS 12"
REAR
OF
UNIT
4"
4"
4-1/8”
7-1/8”
7-1/8”
Center Line
of Unit
1-1/4"
1-1/2"
1-3/4"
1-1/2"
17"
17"
20-7/8"
3"
2"
2"
18-1/2"
3"
Air Grill Perimeter
14-1/4x 14-1/4
(±1/8")
Opening
Genesis
R
e
a
r
F
r
o
n
t
FIG. 5
FIG. 6
DoNotCut
RoofStructure
OrRafters
Good-Rafters
SupportedBy
CrossBeams
GoodLocation-
Between Roof
Rafters
Frame Opening So It
Won't Collapse When
Bolting Down Unit
Leave Access For Power
Supply Wiring
15" Min. At
FrontOf
Opening
3/4" Min.
Standard
Grill
14-1/4x 14-1/4
(±1/8")
Opening

620515, 620525, 620526, 630515 & 630516 Installation Instructions
6
It is the responsibility of the installer to insure
the ductwork will not collapse or bend during
andaftertheinstallation.DometicCorporation
will not be liable for roof structural or ceiling
damage due to improperly insulated, sealed
or collapsed ductwork.
CAUTION
Return Air Cover Model 3105007 3308120
3105935 GenesisAir Filtration System
Roof Cavity Depth 2.0 In. Min. - 5-1/2 In. Max. 2.0 In. Min. - 5-1/2 In. Max.
Duct Cross Sectional Area 21.0 Sq. In. Min. 32.0 Sq. In. Min.
Duct Size
Depth 1-1/2 In. Min. - 2-1/2 In. Max. 2.0 In. Min. - 2-1/2 In. Max.
Width 7.0 In. Min. - 10.0 In. Max. 8.0 In. Min. - 10.0 In. Max.
Total Duct Length 15.0 Ft. Min. - 40.0 Ft. Max. 15.0 Ft. Min. - 40.0 Ft. Max.
Duct Length (short run) 1/3 Total Duct Length 1/3 Total Duct Length
Center Duct System (Only)
Depth 2.0" In. Min. - 2.0" Max.
Width 8.0 In. Min. - 8.0 In. Max.
Total Duct Length 15.0 Ft Min. - 40 Ft. Max.
Duct Length (Short Run) 1/3TotalLength
Register Requirements
Number Required Per Run 4 Min. 4 Min.
Register Free Air Area 14.0 Sq. In. 14.0 Sq. In.
Distance From Duct End 5.0 In. Min. - 8.0 In. Max. 5.0 In. Min. - 8.0 In. Max.
Distance From Elbow 15.0In. 15.0In.
Duct Static
Blower at High Speed,
Filter & Grill In Place 0.12 - 0.65 In. W.C. 0.12 - 0.65 In. W.C.
Note: Duct sizes listed are inside dimensions.
AIR DISTRIBUTION
DUCT SIZING & DESIGN CHART
4. Air Distribution System Sizing & Design
The Installer of this air conditioner system must
designtheairdistributionsystemfortheirparticular
application. Several requirements for this system
MUST be met for the air conditioner to operate
properly.Theserequirementsareasfollows:
a. The duct material must meet or exceed any
agencyorRVIAStandardthatmaybeinexist-
ence at the time the RV is produced.
b. All discharge air ducts must be properly insu-
latedtopreventcondensationfromformingon
their surfaces or adjacent surfaces during op-
eration of the air conditioner. This insulation
must be R-7 minimum.
c. Ductsandtheirjointsmustbesealedtoprevent
condensation from forming on adjacent sur-
facesduringoperationoftheairconditioner.
d. Returnairopeningsmusthave40squareinches
minimumfreeareaincludingthefilter.
e. Returnairtotheairconditionermustbefiltered
toprevent dirt accumulationonair conditioner
coolingsurface.
5. Air Distribution System Installation
a. Dometic Corporation recommends the basic
configuration shown on page 7, for installing
this air conditioner system. We have found by
testing, that this configuration works best in
most applications of this air conditioner sys-
tem.ItistheresponsibilityoftheInstallerofthis
systemtorevieweachRVfloorplananddeter-
minethefollowing:
•Duct size
•Duct layout
•Registersize
•Registerlocation
•Thermostatlocation

620515, 620525, 620526, 630515 & 630516 Installation Instructions
7
Theseitemsmustbedeterminedinconjunctionwiththe
AirDistributionSystemandSizingandDesignRequire-
mentslistedin the chartonpage6.Terminatethe start
oftheductatthebackedgeofthe14-1/4"x14-1/4"(±1/
8"). See FIG. 7, 7A, and 7B.
Important: Alternate configurations and methods
may be used which still allow the air conditioner to
operate properly; however, these alternate configura-
tions and methods must be approved by the Dometic
Corporation in writing. The following instructions are
basedupontheuse of3105007 DometicReturn AirKit,
3105935DometicReturnAirKitor3308120GenesisAir
Filtration System and a 3109228.001 Comfort Control
CenterTM.
FRAME
14-1/4" (±1/8”)
OPENING
AC POWER
SUPPLY WIRE
DUCT
FRAME DUCT
ROOF
INSULATION
DUCT CEILING
DUCT
14-1/4" (±1/8”)
OPENING
INSULATION
SIDE VIEW
(TOWARD BACK OF RV)
TOP VIEW
(BACK OF RV)
LOW VOLTAGE WIRES:
12VDC
Furnace
Load Shed
Sensors
FRAME
CCC, CONTROL CABLE(S)
or 7-Wire Analog Cable
FIG. 7
Register Required
FIG. 7A
FIG. 7B
Duct Size And Requirements For 3105007 And 3105935 Return Air Cover
Duct Size And Requirements For 3308120 Genesis Air Filtration System Kit
Total Outlet Air Area
Minimum 21.0 Sq. In.
Total Outlet Air Area
Minimum 32.0 Sq. In.
Register Required
Register Required
Register Required
Register Required
Register Required Register Required
Register Required
Roof
Rafters
Roof
Rafters
Note: Duct Size is Inside Dimensions
Note: Duct Size is Inside Dimensions
Short Duct Run Minimum
1/3 Total Duct Length
Short Duct Run Minimum
1/3 Total Duct Length
Ducts Min. Max.
Depth 1-1/2” 2-1/2”
Width 7.0” 10.0”
Total Length 15.0’ 40.0’
Ducts Min. Max.
Depth 2.0” 2-1/2”
Width 8.0” 10.0”
Total Length 15.0’ 40.0’
14-1/4"x14-1/4" (±1/8")
RoofOpening
14-1/4"x14-1/4" (±1/8")
RoofOpening
Registers
8 Min.-- 12 Max.
(PerUnit)
14Sq. In FreeArea
PerRegister
Registers
8 Min.-- 12 Max.
(PerUnit)
14Sq. In FreeArea
PerRegister

620515, 620525, 620526, 630515 & 630516 Installation Instructions
8
D. Wiring Requirements
1. 120 VAC Supply Line
Route a copper 12 AWG, with ground, 120 VAC
supplylinefromthetimedelayfuseorcircuitbreaker
boxtotheroof opening.
a. This supply line must be located in the front
portionofthe14-1/4"x14-1/4"(±1/8")opening.
b. ThepowerMUSTbeonaseparate20Amptime
delayfuseor HACR circuit breaker.
c. Make sure that at least 15" of supply wire
extendsintotheroofopening.Thisensuresand
easy connection at the junction box.
d. WiringmustcomplywithallNational,Stateand
LocalWiringCodes.
e. Useasteelsleeveandagrommetorequivalent
methodstoprotectthewirewhereitpassesinto
theopening.
2. Routeadedicated12VDCsupplyline(18-22AWG)
from the RV's converter(filtered terminals) or
batterytotheroof opening.
a. This supply line must be located in the front
portionofthe14-1/4"x14-1/4"(±1/8")opening.
b. Make sure that at least 15" of supply wire
extendsintotheroofopening.
c. Inamultiplezoneinstallation,thiswiringis
requiredinonlyoneofthe 14-1/4"x 14-1/4"
(±1/8")openings.
3. IfaRemoteTemperatureSensorisused,the con-
nectorendmustberoutedfromthesensorlocation
totheroofopeningofthesystemwhichitwillcontrol.
Make sure that at least 15" of the sensor cable
extendsintotheroofopening.RefertotheRemote
Sensor Instructions for details of the installation.
4. Ifafurnaceistobecontrolledbythesystem,thetwo
furnacethermostatleadsmustberoutedtotheroof
opening of the air conditioner that will control it.
Makesurethatatleast15"ofthefurnacethermostat
wiresextendintotheroofopening.
5. Ifan Energy ManagementSystem (load shedfea-
ture) is to be used with the control, two wires must
be routed to the roof opening of the zone to be
managed. The signal required for this function is
normally open relay contact. When the EMS calls
for the compressor to shut off, the relay contacts
should close. Make sure at least 15" of the EMS
wiresextendintotheroofopening.
6. Routea4-conductorcontrolcablefromtheComfort
Control Center™ mounting position into the
14-1/4" x 14-1/4" (±1/8") roof opening. Make sure
that at least 15" of the wire extends into the roof
openingand6"extendfromthewallatthemounting
position of the Comfort Control Center™. See
Section E-2.
7. IntheeventthatotherAirConditionersareinstalled
(additionalzones)anadditional4-conductorcontrol
cablemustberoutedtotheotherAirConditioners.
Makesurethatat least 15" ofthewireextendsinto
theroofopening.SeeFIG. 27.
8. If an automatic generator start kit (AGS) will be
installed, a 4-conductor control cable must be
routed from the last air conditioner to location of
AGSkit.FollowAGSkitinstructionsforinstallation.
E. DometicComfort ControlCenter™&Cable
Installation
1. Location
a. If the system is to be used WITHOUT a Re-
mote Temperature Sensor, the proper loca-
tion of the Comfort Control Center™ is very
importanttoensurethatitwillprovideacomfort-
able RV temperature. Observe the following
rules when selecting a location:
•LocatetheComfortControlCenter™54"
abovethefloor.
•InstalltheComfortControlCenter™ona
partition, not on an outside wall.
•NEVERexposeittodirectheatfromlamps,
sun or other heat producing items.
•Avoid locations close to doors that lead
outside,windowsoradjoiningoutsidewalls.
•Avoid locations close to supply registers
andthe airfrom them.
b. If the system is to be used WITH a Remote
TemperatureSensorinALLzones,theCom-
fort Control CenterTM may be mounted any-
where that is convenient in the coach. Try to
avoidhardtoreachandhardto see areas.
•Referto theinstructions provided withthe
Remote Temperature Sensor fordetails
ofinstallation.
c. A3/8"diameterholewillbeneededtoroutethe
cable through the wall. See Section D-3.
2. ControlCableInstallation
A4-conductorcontrolcablemustberoutedfromthe
roof openingto the Comfort Control CenterTM.
a. Choosetheshortest,mostdirectroutefromthe
14-1/4" x 14-1/4" (±1/8") opening to the Com-
fortControl CenterTMlocationselected.Leave
6" of cable extending through the wall. See
SectionD-6.
b. Thecontrol cable thatshould beused is aflat,
4-conductortelephonecable.
c. Thecontrolcablemustbeterminated withtwo
(2)RJ-11-6C4Ptelephoneconnectors.Referto
thecrimptoolmanufactureforcrimpinginstruc-
tions. See FIG. 8A, 8B and 8C.

620515, 620525, 620526, 630515 & 630516 Installation Instructions
9
Important:RJ-11-6C4Pconnectorsmustbeinstalled
as shown in FIG. 8A, 8B & 8C.
3.ComfortControlCenterTM Installation
a. CarefullyremovethebaseplatefromtheCom-
fort Control CenterTM. This may be accom-
plishedby insertingasmallscrewdriverunder
the tab on thebottom edge of the front cover
and gently prying. See FIG. 9.
b. Insertthe control cablethrough the holein the
baseplateand mounttheplatetothewallwith
two(2)screwsprovided.Checkthealignmentto
ensurelevelinstallation.
c. InstallthecontrolcableRJ-11-6C4Pconnector
intothebackoftheComfortControlCenter™
and snap onto the base plate. See FIG. 9.
F. Placing Air Conditioner On The Roof
1. Removetheair conditioner fromthecartonand dis-
card carton. See FIG. 10.
2. Place the air conditioner on the roof.
This unit weighs approximately 100 pounds.
Topreventbackinjury,useamechanicalhoist
to place Air Conditioner on roof.
Do not slide the unit. This may damage the
roof gasket attached to the bottom and may
create a leaky installation.
CAUTION
FIG. 8A
FIG. 8B
Flat Four Conductor Cable
RJ-11-6C4P
Connector
Pin1
FIG.8C
Black
Green
Red
Yellow
Black
Green
Red
Yellow
Insert Screwdriver
under Tab
Insert Screwdriver
under Tab
MODE
MODE
FAN
FAN
UP
UP
DOWN
DOWN
OFF ON
OFF ON
ZONE
ZONE
TEMP
TEMP
FIG. 9
FIG. 11
FRONT
FIG. 10
3. Liftandplacetheunitoverthepreparedopeningusing
the gasket on the unit as a guide. See FIG. 11.
4. Place the Return Air Kit inside the RV. This box
contains mounting hardware for the air conditioner
and will be used inside the RV.
This completes the outside work. Minor adjustments
can be done from the inside of the RV if required.

620515, 620525, 620526, 630515 & 630516 Installation Instructions
10
CAUTION
If bolts are left loose there may not be ad-
equate roof seal or if over tightened, damage
may occur to the air conditioner base or ceil-
ing template. Tighten to specifications listed
in this manual.
e. InstalltheRomexconnectorin thejunctionbox.
f. Hold the ceiling template up to the 14-1/4" x
14-1/4"(±1/8")opening.Be sure the largeplate
faces the rear of the RV.
g. Starteachmountingboltthroughtheceilingtem-
plate and up into the unit base pan by hand.
Install wood screw in each end of the ceiling
template.Thisinsuresatightfitofthereturnair
cover to ceiling. See FIG. 14. Evenly tighten
mounting bolts to compress gasket to 1/2"
this will be a torque of 40 - 50 inch pounds.
The bolts are self locking so over tighten-
ing is not necessary. See FIG. 15.
2. InstallationofDividerPlate
a. Measure the ceiling to roof thickness:
• If distance is 2.0" - 3-3/4", remove perfo-
ratedtabfromdividerplate.
• Ifdistanceis3-3/4”-5-1/2”,removenotabs.
b. Remove the backing paper from double sided
tape located on ceiling template. See FIG. 16.
G. Installing The Air Conditioner
Installing Unit with 3105007 or 3105935 Return Air
Kit.ForunitwithGenesisAirFiltrationSystem,see
page 11.
1. InstallationOfCeilingTemplate
a. Check gasket alignment of the air conditioner
over the roof opening and adjust if necessary.
Unit may be moved from below by slightly lift-
ingand moving. SeeFIG. 13.
b. Remove return air cover and ceiling template
fromthe3105007or3105935carton.
c. Locatethefour(8"x1/4-20)unitmountingbolts,
junctionboxcoverandRomex connector in the
3107180bolt kit.
d. Pull down the unit's electrical cord and fasten
the junction box with screws to the framing in
the front of the 14-1/4" x 14-1/4" (±1/8") open-
ing. See FIG. 14.
FIG. 12 Divider Plate
Ceiling Template Return Air
Cover
Return Air
Grill
FIG. 13 Center Unit From Below
Roof
Gasket
DC Power Gasket
Pull Electrical
Cord Down
FIG. 14
AC Power
Supply
Fasten Jct. Box To
Front Of Opening
Furnace
UnitCCC
Connectors
FIG. 16
FIG. 15
Finger
Tight
Front of Vehicle
Tighten to
compressgasket
to 1/2"
Roof
Gasket
Screws

620515, 620525, 620526, 630515 & 630516 Installation Instructions
11
Improper installation and sealing of divider
platewillcausethecompressortoquickcycle
onthe cold control. This may result in fuseor
circuit breaker opening and/or lack of cool-
ing.
CAUTION
c. Place divider plate up to bottom of air condi-
tioner base pan firmly. The foam tape on the
divider plate must seal to bottom of base pan.
See FIG. 17.
Note: The adhesive on the insulation is extremely sticky.
Be sure the part is located where desired before pressing
into place.
d. Withslightpressurethenpushthedividerplate
against the double sided tape on the ceiling
template.
e. Locatethe1/8”x 7” x 18” self-adhesiveinsula-
tionsuppliedwiththereturnairkit.Removethe
backingpaperfromtheinsulationandcarefully
stick onto the ceiling template divider panel.
See FIG. 18.
•Excess width is intended to seal the di-
viderplate to the sidesofthe 14-1/4" x14-
1/4" (±1/8") opening. This is to help pre-
ventcoldairdischargefrom circulating into
theairconditioner return air opening.
•If the insulation is too high, stick excess
height of insulation to the air conditioner
basepan.Donot cover up unitratingplate.
Installing unit with 3308120 Genesis Air Filtration
System Return Air Kit. For unit with 3105007 or
3105935 Return Air Kit, see page 9.
1. AllNon-CenterDuct Installations
Note:TheGenesisAirFiltration System can be installedon
unitsthatuse a center dischargeductthroughthe14-1/4"x
14-1/4"(±1/8") opening. Installingunitswith the centerdis-
chargeduct go to Section1."Center Discharge DuctAppli-
cation Installation", on page 6.
a. Check gasket alignment of the air conditioner
over the roof opening and adjust if necessary.
Unit may be moved from below by slightly lift-
ingand moving. SeeFIG. 13.
•Removereturn air cover,ceilingtemplate,
foamdividerandair filter fromthe3308120
carton.
•Locatethefour (8" x 1/4-20)unitmounting
bolts, junction box cover and Romex con-
nector in the 3107180 bolt kit.
•Pulldowntheunit'selectricalcordandfas-
ten the junction box with screws to the
framinginthefront of the 14-1/4" x14-1/4"
(±1/8")opening. See FIG. 14.
b. InstallingFoamDivider
•Locate the foam divider and insert it cor-
ner to corner in the 14-1/4" x 14-1/4" (±1/
8")opening with the adhesivetapeup (Do
notremovepapertoexposeadhesive).The
foamdividershouldbelevelwiththe ceiling
(±1/4"). Tear off the excess at the pre-cut
perforationsindivider. See FIG. 20.
FIG. 17
FIG. 18
Micro-Therm Filter System
Micro-Therm Filter System
FILTER
RESET
FILTER
RESET
CLEAN
FILTER
CLEAN
FILTER
Return Air
Cover
FIG. 19
Grill
Foam
Divider Ceiling
Template
Slider Filter
Handle
Genesis Air Filtration System
Return Air Kit

620515, 620525, 620526, 630515 & 630516 Installation Instructions
12
e. Use Aluminum foil tape (not supplied) to seal
theends of thefoam divider to thesides of the
opening.Makesuretheareabehindtheflange
onthe ceiling template is sealed.See FIG. 22.
2. CenterDischargeDuctApplicationInstallation
Note: Ifusing non-centerduct installation, go to Section1.
"AllNon-Center Duct Installations",onpage11.
Important:Aduct adapter (not supplied) must be installed
betweentheunit dischargeandthe customer installed cen-
ter duct. This duct adapter must be approved by Dometic.
a. Check gasket alignment of the air conditioner
over the roof opening and adjust if necessary.
Unit may be moved from below by slightly lift-
ingand moving. SeeFIG. 13.
•Removereturnair cover, ceilingtemplate,
foamdividerandair filter fromthe3308120
carton.
•Locatethefour(8" x 1/4-20) unit mounting
bolts, junction box cover and Romex con-
nector in the 3107180 bolt kit.
•Pulldowntheunit'selectricalcordandfas-
ten the junction box with screws to the
framinginthefront of the 14-1/4" x14-1/4"
(±1/8")opening. See FIG. 14.
b. InstallingFoamDivider
•Cutnotchinthecenter section of the foam
divider to fit (approximately 2 x 8 inches)
snugly around duct. See FIG. 23.
Improper installation and sealing of foam di-
viderwillcausethecompressortoquickcycle
onthe cold control. This may result in fuseor
circuit breaker opening and/or lack of cool-
ing.
CAUTION
If bolts are left loose there may not be ad-
equate roof seal or if over tightened, damage
may occur to the air conditioner base or ceil-
ing template. Tighten to specifications listed
in this manual.
CAUTION
c. Install CeilingTemplate
•Peel the paper off of the foam divider and
stick it in place on the center of the rear
flangeofthe return air opening ontheceil-
ing template. See FIG. 21.
d. Starteachmountingboltthroughtheceilingtem-
plate and up into the unit base pan by hand.
EVENLY tighten the three bolts to a torque
of 40 to 50 inch pounds. This will compress
the roof gasket to approximately 1/2". The
bolts are self locking so over tightening is
not necessary.
FIG. 20
Upside
Down
Foam
Divider
Base Pan
Ceiling
Place Foam Divider in
(14-1/4" x 14-1/4" (±1/8")
CeilingOpening against
Base Pan Bottom
Do Not Peel Tape Off
Adhesive
FoamDivider Ceiling
Level (±1/4")Tear Off
Excess
FIG. 21 Foam Divider
Adhesive
Peel Off Paper - Center Divider - Stick To
Rear Flange On Ceiling Template
FIG. 22 UseAluminumFoil Tape To Sealthe
Foam Divider To The Sides of 14-1/4"
x 14-1/4" (±1/8") Ceiling Opening
Make Sure To Seal
BehindFlange
Route wires
through Slot
CatchFlange InGroove Of
Return Air Cover
FIG. 23
Foam
Divider
Mark And Cut 2” x 8”
Opening For Center Duct
Tape Covered
Adhesive

620515, 620525, 620526, 630515 & 630516 Installation Instructions
13
If bolts are left loose there may not be ad-
equate roof seal or if over tightened, damage
may occur to the air conditioner base or ceil-
ing template. Tighten to specifications listed
in this manual.
CAUTION
Improper installation and sealing of foam di-
viderwillcausethecompressortoquickcycle
onthe cold control. This may result in fuseor
circuit breaker opening and/or lack of cool-
ing.
CAUTION
•Placethefoamdividerinthereturnairopen-
ingabove the center ductbeforeinstalling
ceilingtemplate.
c. Install CeilingTemplate
•Applyapieceoffoamweatherstripping(not
supplied) to the upper side of ceiling tem-
plate to make a seal between it and the
duct.Usea softpieceoffoamweatherstrip
1 x 3/4 x 10 inches. See FIG. 24.
d. Starteachmountingboltthroughtheceilingtem-
plate and up into the unit base pan by hand.
EVENLYtighten the three bolts to a torque
of 40 to 50 inch pounds. This will compress
the roof gasket to approximately 1/2". The
bolts are self locking so over tightening is
not necessary.
e. Use Aluminum foil tape (not supplied) to seal
theends of thefoam divider to thesides of the
opening.Makesuretheareabehindtheflange
onthe ceiling template is sealed.See FIG.22.
f. Cut the opening in the center duct using the
dischargeopening in the ceilingtemplatefor a
pattern.Sealthecenterducttothe ceiling tem-
plate using foil tape, foam insulation or silicon
sealant.
CAUTION
Disconnect the positive (+) 12 volt DC termi-
nal at the supply battery. Damage to equip-
ment could occur if the 12 volt DC is not shut
off.
H. Wiring The System
Reach up into the return air opening and pull the re-
mainingwiresdown.
1. ConnectionOfLow VoltageWires
Note: If solar panel is installed see instructions packaged
withsolar panel option.
Note: If using the Genesis Air Filtration System step "b" is
tobecompletedwheninstallingthedecorativecover.
a. RouteRemoteTemperatureSensorcable,if
applicable, and attach it to the connector that
matches its color in the control box.
b. Connect the previously run 12 VDC to the red
and blackwiresprotrudingfromthecontrolbox.
(Inmultiplezoneinstallations,thisneedstobe
done atonlyonezone.)Connect+12VDCto
the red wire; –12 VDC to the black wire.
c. Connectthepreviouslyrunfurnacethermostat
wires(ifapplicable)tothebluewiresprotruding
from the control box. The polarity of these
connections does not matter.
d. Connect the previously run Energy Manage-
mentSystemwires(ifapplicable)totheyellow
wiresprotrudingfromthecontrolbox.Thepolar-
ity of these connections does not matter.
e. Terminatethe4-conductorcontrolcable(s)pro-
truding into the 14-1/4" x 14-1/4" (±1/8") roof
opening.Thecable(s)mustbeterminatedwith
atelephoneRJ-11-6C4Pconnector.Refertothe
crimp tool manufacturer for crimping instruc-
tions.
Important:RJ-11-6C4Pconnectorsmustbeinstalled
as shown in FIG. 8A, 8B & 8C.
f. Plug the control cable(s) into the telephone
jack(s) on the control box. (It does not matter
whichone.)
g. Locate the ambient sensor plug coming from
the unit, and attach it to the connector that
matches its color in the control box.
2. ConnectionOf 120VoltPowerSupply
Disconnect120voltAC. Failure to follow these
instructions could create a shock hazard
causing death or severe personal injury.
FIG. 24 Stick Weather Strip To Top
Of Ceiling Template
Weather Strip
Ceiling
Template

620515, 620525, 620526, 630515 & 630516 Installation Instructions
14
Installing unit with 3308120 Genesis Air Filtra-
tion System Return Air Kit. For 3105007 or
3105935 Return Air Kit, see page 14.
1. Install the slider in the return air cover and raise it
to the ceiling template. Route the filter indicator
wiresfromthereturnaircoverthroughthe template
slot leaving about 3” between. Place the front of
the return air cover against the ceiling and slide
towards the rear. The flange on the ceiling tem-
plate will catch in the groove on the return cover.
Adjusttheposition (right to left)andinstallthefront
twoscrews.Startandtightentheremaining screws
tohold it inplace.Connect together thewiresfrom
the thermostat, unit and filter indicator.
Note: If solar panel is installed see instructions packaged
withsolar panel option.
a. Connecttheredwirefromtheunit,theredwire
from the filter indicator light with the red DC
positivepower lead.See FIG.21.
b. Connect the black (-12V) wire from the unit,
theblack wire from thefilter indicator light with
theblack (-12V)power lead.
Note:Number10cabinetscrew can be used toreplacethe
two front screws when the ceiling material is hard.
2. Tightenthescrewsholdingthereturnaircover.Slide
thefilter from theright side (lookingtowardthe RV
front)overthewires.Makesurethewires areabove
the filter and are out of its way.
3. Place grill on return air cover and snap in place,
and install decal on end over circuit board.
4. Place slide handle through slots in grill into the
slide posts. Handle will fit in either direction.
5. Thiscompletestheinstallationofthe airconditioner.
We recommend that power be supplied to the air
conditionerandcheck forproperoperation.Referto
OperatingManualorUser’sGuideforadescription
oftheair conditioner operation.
This product is equipped with a 3-wire
(grounded) system for protection against
shockhazard.Makesurethattheapplianceis
wired into a properly grounded 120 volt AC
circuitandthepolarityiscorrect.Failuretodo
so could result in death, personal injury or
damage to the equipment.
a. Route power supply line through Romex con-
nectorinto junction boxon sideaway from the
ceilingtemplate.Tightenconnector,beingcare-
ful not to pinch or short wires.
b. Connect white to white; black to black; and
greentogreenorbarecopperwireusingappro-
priate sized twist connectors.
c. Tape the twist wire connectors to the supply
wireto assuretheydon'tvibrateoff.
d. Push the wires into the box.
e. Install the cover onto the junction box.
I. Installing Decorative Inside Cover
Installing unit with 3105007 or 3105935 Return
Air Cover. For Genesis Air Filtration System
Return Air Kit, see page 14.
1. Removethereturnairgrillfromthereturnair cover.
2. Place the return air cover up to the ceiling tem-
plate.
3. Install cover to template with #8 x 3/8” blunt point
Phillipsheadscrewsprovided(6required).
4. Reinstall filter return air grill into return air cover.
Aligntabswithmating notches and snap intoplace
5. Install two hole plugs into screw holes in back of
returnair cover.SeeFIG. 24.
6. Thiscompletestheinstallationofthe airconditioner.
We recommend that power be supplied to the air
conditionerandcheck forproperoperation.Referto
OperatingManualor Users Guide for adescription
oftheair conditioner operation.
Micro-Therm Filter System
Micro-Therm Filter System
FILTER
RESET
FILTER
RESET
CLEAN
FILTER
CLEAN
FILTER
Return Air
Cover
FIG. 25
Grill
Foam
Divider Ceiling
Template
Slider Filter
Handle
Genesis Air Filtration System
Return Air Kit
FIG. 24 Return Air
Cover
Hole
Plugs Return
Air Grill

620515, 620525, 620526, 630515 & 630516 Installation Instructions
15
J. SystemConfiguration,Reset & Check Out
Nowthat thesystemisinstalled,itisnecessarytocheckall
operationsand thenconfigure the electronics.Refer to the
Operating manual for a description of the air conditioner
operation.
1. ElectronicControlKitConfiguration
Depending on the equipment options installed by the
recreational vehicle manufacturer, the appropriate dip
switches will need to be switched to the "ON" position.
Placing the switch in the "ON" position selects that
option. See FIGS. 26, 26A & 26B.
d. Differential-differentialisthetemperaturediffer-
encebetweenthe"ON/OFF"cycle of the ther-
mostatinthefurnacemode.Thenormaldiffer-
ential is preset in the circuit board with the dip
switch set to the "OFF" position. In some
situations,itmaybenecessarytodecreasethe
differential.Thelocationofthethermostatmay
createaconditionwherethenormaldifferential
will not maintain your comfort zone. If this
occurs, the differential can be shortened by
placing the differential dip switch to the "ON"
position.
Note: Setting the differential dip switch should only be
requiredwheninstallationconditionsarelessthandesirable
andisnotcovered under thelimitedwarranty.
e. Stage selection - stage is not used on these
units. Leave in the "OFF" position.
f. Genstartselection-leaveinthe"OFF"position.
g. Replacetheunit electrical boxcover.
h. Repeatthisprocedureforeachadditionalzone.
2. System Reset
After setting the dip switches in the electronic
control kit, do a system reset.
a. TurntheON/OFFswitchtothe"OFF"position.
b. Simultaneously depress and hold the MODE
and ZONEpush-buttonswhile turningtheON/
OFFswitch to "ON". FFshouldappear in LCD
display until the mode and zone push-buttons
arereleased.
c. When a dip switch is turned on after initial
configuration, a system reset will need to be
donebeforetheComfortControlCenter™will
recognizetheupdatedselection.
3. System Checkout
Verifythatallfeaturesoftheinstalledsystemwork.
Checkfanspeeds,coolingmode,heatpumpmode,
furnace(ifconnected)andheatstrip.Ifthefeatures
do not work, check all wiring and confirm that the
correct options have been selected on the Elec-
tronicControlBox.SeeComfortControlCenter™
OperatingInstructions.
Note:Dipswitchesareinthe"OFF"positionwhenshipped
from the factory. The dip switches are visible through the
opening in the ceiling template into the control box.Dip
switches can be either a rocker or sliding style of a switch.
See FIGS. 26, 26A & 26B.
Important: Dip switch damage will occur if they are
notsetinthepropermanner.Aballpointpenorsimilar
object that will slip in the switch slot, can damage the
switchcausinglossofconnection.Useonlyasmallflat
blade screw driver (wider than the dip switch slot) to
move the dip switch. See FIG. 26C.
b. Heatstripselection:Unitswithaheatstrip,the
#1 dip switch will be in the "ON" position.
c. Furnace selection - when a furnace has been
connected to a zone, place the furnace dip
switch "ON" for that zone.
12 345
ON
678
12 345
ON
678
FIG. 26C
NotCorrect
Use Flat Blade Screw-
driver Wider Than Dip
Switch Slot To Move Dip
Switch
DO NOT USE
BALLPOINT
PEN To Move
Dip Switch
Correct
FIG. 26
12 345
HEAT STRIP
ZONE 2
ZONE 3
ZONE 4
FURNACE
ON
678
DIFFERENTIAL
STAGE
GEN START
SLIDE
SWITCH
SLIDE
SWITCH
12345
HEAT STRIP
ZONE 2
ZONE 3
ZONE 4
FURNACE
OPEN
678
DIFFERENTIAL
STAGE
GEN START
ROCKER
SWITCH
ROCKER
SWITCH
FIG. 26A FIG. 26B
Dip Switches
All Switches "OFF" All Switches "OFF"

620515, 620525, 620526, 630515 & 630516 Installation Instructions
16
REAR REMOTE SENSOR
(Required with Second
Air Conditioner)
REAR REMOTE SENSOR
(Required with Second
Air Conditioner)
14-1/4" x 14-1/4"
(±1/8”) OPENING
14-1/4" x14-1/4"
(±1/8”) OPENING
14-1/4" x 14-1/4"
(±1/8”) OPENING
14-1/4" x14-1/4"
(±1/8”) OPENING
OPTIONAL
FURNACE
OPTIONAL
FURNACE
FURNACE
2 WIRES
FURNACE
2WIRES
OPTIONAL FRONT
REMOTE SENSOR
OPTIONAL FRONT
REMOTE SENSOR
12V DC INPUT
2 WIRES
12V DC INPUT
2WIRES
FURNACE
4-CONDUCTOR
CONTROL CABLE
4-CONDUCTOR
CONTROL CABLE
BREAKER BOX
BREAKER BOX
115V AC
REAR A/C
115V AC
REAR A/C
4-CONDUCTOR
CONTROL CABLE
4-CONDUCTOR
CONTROL CABLE
115V AC
FRONTA/C
115V AC
FRONTA/C
FURNACE
2 WIRES
FURNACE
2WIRES
DOMETIC COMFORT
CONTROL CENTER
DOMETIC COMFORT
CONTROL CENTER
FIG. 27
CONTROL
TO COMFORTTO COMFORT
RJ-11 CABLERJ-11 CABLE
BLK
COM
LOAD SHEDLOAD SHED YEL
RED
BLU
NO
DIRTY FILTER
IF USEDIF USED
INDICATORS
BLK
FURNACE
FURNACE
SOLAR ORSOLAR OR
12V +12V +
12V -12V -
K6
T3
BLU
T2
BLK
BLU
COM
K1
NO
CABLE
FUSE
3AMP3 AMP
FACTORY WIRING
FIELD WIRINGFIELD WIRING
F1
LOAD SHEDLOAD SHED YEL
P3
BOARD
MODULE
POWER
A/C
T5
P6
WHITE
WHITE
P4
BLK
P5 P2
CONTROL
FREEZE
SENSOR
REMOTE
BLK
HEATER ELEMENTHEATER ELEMENT
GRN/YEL
WHT
T1
BLK
GRN/YEL
LIMIT SWITCH
GRY
WHT
1O
CONDUCTORSCONDUCTORS
USE COPPERUSE COPPER
3308032.063 ONLY
60 Hz,60 Hz,
115 VAC115 VAC
MODELS
ON SOMEON SOME
NOT USED
O.L.
R
WHT
BLK
BLK
RED
YEL
P1
BLU
HERM
WHT
WHT
RED
FAN
RUN CAPRUN CAP
BRN
WHT
WHT
C
MOTOR
GRN/YEL
BLU
S
CRED
COMPRESSOR
PASSED
DIELECTRIC
START CAP
STARTER
MOTOR
REMOTE
SENSOR
CABLE
WHITE
P4
BLU
DIRTY FILTER
DIRTY FILTER
INDICATORS
IF USED
IF USED
BLK NO
SOLAR OR
SOLAR OR
BOARD
MODULE
MODULE
POWER
FURNACE
FURNACE
LOAD SHED
LOAD SHED
LOAD SHED
LOAD SHED
12V +
12V +
12V -
12V -
FUSE
COM
RED
BLU
K6
BLK
YEL
YEL
BLU
P3
A/C
3 AMP
3AMP
F1
T3 T1
T2
BLK
BLK
COM
P6
NO
K1
WHITE
T5
P5
AMBIENT
SENSOR
P2
BLK
BLK
YEL
P1
BLK
BLU
BLK
DIELECTRIC
PASSED
CONTROL
RJ-11 CABLE
RJ-11 CABLE
TO COMFORT
TO COMFORT
FREEZE
CONTROL RED
S
R
3308032.089
60 Hz,
60 Hz,
115 VAC
115 VAC
ONLY
CONDUCTORS
USE COPPER
USE COPPER
FIELD WIRING
FIELD WIRING
SPLICE CAP
SPLICE CAP
FACTORY WIRING
FACTORY WIRING
GRN/YEL
WHT
GRN/YEL
START CAP
START CAP
FAN
RUN CAP
RUN CAP
HERM
REVERSING
VALVE
REVERSING
VALVE
BLK
BLK
WHT
WHT
WHT
C
BRN
STARTER
MOTOR
WHT
C
RED
1o
RED
COMPRESSOR
BLU
GRN/YEL
MOTOR O.L.
630515 & 630516 WIRING DIAGRAM
620515, 620525 & 620526 WIRING
DIAGRAM