FULL FULL BUNK BED ASSEMBLY:
STEP #1 (SEE #01 ILLUSTRATION)
INSERT DOWELS (F) INTO BOTH ENDS OF ALL SIDE
RAILS.
STEP #2 (SEE #02 ILLUSTRATION)
ATTACH BRACKETS (G) WITH SCREWS ( K) ON BOTH
TALL HEAD BOARDS AND BOTH SHORT FOOT
BOARDS. THE HOLES ARE PRE MARKED AND
ASSEMBLE WITH THE OPEN END OF BRACKET UP.
STEP #3 (SEE #03 ILLUSTRATION)
INSERT DOWEL AT THE END OF THE SIDE RAILS
INTO THE HEAD BOARD SECTIONS (01) AND TIGHTEN.
STEP #4 (SEE #04 ILLUSTRATION)
INSERT DOWEL AT END OF THE SIDE RAILS INTO
THE FOOT BOARD POSTS (02,03) AND START TO
TIGHTEN. AT TACH GUARD RAILS WITH NUT (C) AND
BOLT (A). FULLY TIGHTEN ALL BOLTS.
STEP #5 (SEE #05 ILLUSTRATION)
INSTALL ONE CENTER BEAM IN THE HEAD BOARD
BRACKETS AND ONE CENTER BEAM IN THE FOOT
BOARD BRACKETS. CUT OUTS ON E NDS OF CENTER
BEAM GO DOWN. BEAM WITH HOLES FOR LEGS GOES
ON HEAD BOARD SECTION. ATTACH LEGS WITH
DOWEL (F) AND BOLT (L). ATTACH CENTER BEAM TO
BRACKETS WITH BOLT (I) AND TIGHTEN WITH NUT (H)
STEP #6 (SEE #06 ILLUSTRATION)
INSTALL ONE SLAT KIT ON THE HEAD BOARD
SECTION AND ONE SLAT KIT ON THE FOOT BOARD
SECTION. USE NINE SCREWS ( D) AND SCREW DOWN
FIRST SLAT, LAST SLAT AND
THE MIDDLE SLAT.
THE FIRST AND LAST SLAT MUST START AT THE
BEGINNING OF THE CLEAT OF THE SIDE RAIL.
MAXIMUM 3.25” AIR SPACE FROM SLAT TO END OF
HEAD AND FOOT BOARDS.
STEP #7 (SEE #07 ILLUSTRATION)
PUT THE BIG DOWELS (E) IN THE HOLES AT THE TOP
OF THE HEAD BOARD POSTS. WITH TWO PEOPLE
TAKE CARE AND LIFT THE FOOT BOARD SECTION
AND INSERT INTO THE DOWELS ON TOP OF THE
HEAD BOARDS. HEAVY LIFTING, TAKE CAUTION.
STEP #8 (SEE #08,09 ILLUSTRATION)
FOR THE SMALL GUARD RAIL INSERT DOWELS (F)
INTO THE TWO GUARD RAIL BOARDS (08). NOW
INSTALL THOSE DOWELS INTO POST (09) AND
TIGHTEN WITH BOLT (L). INSTALL THE GUARD RAIL
INTO THE FOOT BOARD POST BY INSERTING DOWELS
AND TIGHTEN WITH BOLTS (J). ATTACH GUARD RAIL
POST WITH TWO SCREWS (D). FOR THE OPPOSITE
BUNK POST INSERT THE BOLT ( PART A) INTO PART M
AND TIGHTEN, AS SHOWN AT BOTTOM OF STEP 09.
SIZE OF MATTRESS
THIS BED IS DESIGNED TO USE A MATTRESS (74” TO
75”) LONG AND (52.5” TO 53.5”) IN WIDTH AND THE
ENCLOSED SLAT KIT SYSTEM. THE TOTAL THICKNESS
OF UPPER OR LOWER MATTRESS AND FOUNDATION
MUST NOT EXCEED 9.25”. NOTE THERE MUST BE AT
LEAST 5” FROM MATTRESS SLEEPING SURVACE TO
TOP EDGE OF GUARDRAIL.
REPLACEMENT PARTS
REPLACEMENT PARTS, INCLUDING ADDITIONAL
GUARD RAILS MAY BE OBTAINED FROM ANY OF OUR
INNOVATIONS DEALERS.
SAFETY WARNINGS
1. FOLLOW THE INFORMATION ON THE WARNINGS
APPEARING ON THE UPPER BUNK END STRUCTURE
AND ON THE CARTON. DO NOT REMOVE WARNING
LABEL FROM BED.
2. ALWAYS USE THE RECOMMENDED SIZE
MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO
HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT
OR FALLS.
3. SURFACE OF MATTRESS MUST BE AT LEAST 5
INCHES BELLOW THE UPPER EDGE OF
GUARDRAILS.
4. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF
AGE TO USE THE UPPER BUNK.
5. PERIODICALLY CHECK AND ENSURE THAT THE
GUARD RAIL, LADDER, AND OTHER COMPONENTS
ARE IN THEIR PROPER POSITION, FREE FROM
DAMAGE, AND THAT ALL CONNECTORS ARE TIGHT.
6. DO NOT ALLOW HORSEPLAY ON OR UNDER THE
BED AND PROHIBIT JUMPING ON THE BED.
7. ALWAYS USE THE LADDER FOR ENTERING OR
LEAVING THE UPPER BUNK.
8. DO NOT USE SUBSTITUTE PARTS. CONTACT
MANUFACTURER OR DEALER FOR REPLACEMENT
PARTS.
9. USE OF A NIGHT L IGHT MAY PROVIDE ADDED
SAFETY PRECAUTION FOR A CHILD USING THE
UPPER BUNK.
10. ALWAYS USE GUARD RAILS ON BOTH LONG
SIDES OF THE UPPER BUNK.
11. IF THE BUNK BED WILL BE PLACED NEXT TO A
WALL, THE GUARD RAIL THAT RUNS THE FULL
LENGTH OF THE BED SHOULD BE PLA CED AGAINST
THE WALL TO PREVENT ENTRAPMENT BETWEEN
THE BED AND THE WALL.
12. PROHIBIT MORE THAN ONE PERSON ON THE
UPPER BUNK.
13. THE USE OF WATER OR SLEEP FLOTATION
MATTRESSES IS PROHIBITED.
14. KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
STRANGULATION HAZARD – NEVER ATTACH OR
HANG ITEMS TO ANY PART OF THE BUNK BED THAT
ARE NOT DESIGNED FOR USE WITH THE BED: FOR
EXAMPLE, BUT NOT LIMITED TO HOOKS, BELTS AND
JUMP ROPES.
DONCO TRADING
FORT WORTH, TX
