Donco 1019 User manual

STAIRWAY BUNK BED
Thank you for purchasing this quality product.
Be sure to check all packing materials carefully
for small parts which may have come loose
inside the carton during shipment. Separate,
identify and count all parts and hardware.
Compare with the parts list to be sure all parts
are present.
´´DO NOT TIGHTEN SCREWS
UNTIL COMPLETELY ASSEMBLED´´
SAFETY WARNINGS!
1- Follow the information on the warning label appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
2- Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
of entrapment or falls.
3- Surface of mattress must be at least 5 inchess below the upper edge of guardrails.
4- Do not allow children under 6 years of age to use the upper bunk.
5- Prohibit more than one person on upper bunk.
6- Periodically check and ensure that the guardrail, ladder and other components are in their proper position,
free from damage, and that all connectors are tight.
7- Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8- Always use the ladder for entering and leaving the upper bunk.
9- Do not use substitute parts. Contact distributor or dealer for replacement parts.
10- Use of a night light may provide added safety precaution for a child using the upper bunk.
11- If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should
be placed against the wall to prevent entrapment between the bed and the wall.
12-Always use guardrails on both long sides of the upper bunk.
13-The use of water or sleep flotation mattresses is prohibited.
14-Keep these instructions for future reference.
15-Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed: for example, but not limited to, hooks, belts, and jump ropes, etc.
IMPORTANT: PLEASE READ INSTRUCTIONS BEFORE STARTING THE ASSEMBLY
In t
sctio s
un
r
st ctions
ru
ASSEMBLY INSTRUCTIONS
SIZE OF MATTRESS AND FOUNDATION (SUPPORT)
total thickness must not exceed inchess. Do not use mattress without the proper bunkie board of safe9"
foundation.
Note: There must be at least inches from top surface of mattress to top edge or guardrails.5"
TO OBTAIN PARTS, PLEASE CONTACT:
This bed is designed to use a twin mattress ( 37 ½´´- 38 ½´´x 74 - 75´´) and bunkie board (37 ½´´x 74´´). The
REPLACEMENT PARTS.
Replacement parts, including additional guardrails, may be obtained from place of purchase or original
distributor.
1019 TWIN TWIN MISSION
DONCO TRADING COMPANY- FORT WORTH,TEXAS

ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. Be sure to check all packing
material carefully for small parts which may have come loose inside the
carton during shipment. Separate, identify and count all parts and hardware.
Compare with the parts list to be sure all parts are present.
"DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED”
IMPORTANT:
PLEASE READ INSTRUCTION BEFORE STARTING THE ASSEMBLY
* Use of power tool to assemble this
product will invalidate any claim and
damage this product making unsafe !!!
* Please assemble on a clean soft
surface to avoid damage.
!
(Hammer)
Tools Required
(Not included)
(Not included)
+
2:00 h
1
2
3
4
5
6
7
8
9
10
11 12
1019 TWIN TWIN MISSION STAIRWAY BUNK BED
LEFT RIGHT
ATTENTION
OPTIONS

Identifying the Hardware/part list- Identify the hardware using the illustrations below.
Part List: 1019 TWIN TWIN MISSION STAIRWAY BUNK BED
4,0 x 30 Screw
D32
Qty
01
CQty
08
7,0 x 80 Screw
10x40 Wood Dowel
15x100 Wood Dowel
1/4 x 90 Screw
A
F
Qty
16
Qty
Half Moon
04
BQty
1/4" 16
Qty
G17
E
Qty
Hex Screwdriver
WARNING LABELS
NOT REMOVE !
x2
2
1
4
4
3
5
5
5
5
6
8
7
7
7
7
4
4
1

01
G
G
G
G
G
10x40 Wood Dowel
Qty
G16
x4
x4
5
4

``INSTALL SLAT KIT WITH SPACER
TAPE ON TOP (FACING UP)``
02
03
B
B
B
BOTTOM BED
F
15x100 Wood Dowel
FQty
04
4,0 x 30 Screw
D08
Qty
A
A
E
E
A
A
E
E
A
A
E
E
1/4 x 90 Screw
A
Half Moon
Qty
08
B1/4" Qty
08
Qty
01
EHex Screwdriver
F
D
A
A
E
E
F
F
F
D
D
D
!
The first slats must be fixed at
3" from each headboard end.
D
SIDE-RAIL
L
SAT
1
1
4
4
6
D
D
D
D

0404 B
B
B
1/4 x 90 Screw
AHalf Moon
Qty
08 B1/4" Qty
08
Qty
01
E
05
4,0 x 30 Screw
D08
Qty
CQty
08
7,0 x 80 Screw
C
E
CE
Hex Screwdriver
A
A
E
EA
A
E
E
C
F
CE
A
A
E
E
A
A
E
E
D
D
D
D
!
The first slats must be fixed at
3" from each headboard end.
D
SIDE-RAIL
L
SAT
3
2
4
5
5
4
5
5
6
D
D
D
D
``INSTALL SLAT KIT WITH SPACER
TAPE ON TOP (FACING UP)``
TOP BED

D
D
D
D
06
07
4,0 x 30 Screw
D12
Qty
D
D7
7
7
7
D
D
D
D
D
D

OPTIONS
LEFT RIGHT
GG
08
10x40 Wood Dowel
Qty
G01
09
D
D
88
LEFT RIGHT
4,0 x 30 Screw
Qty
D04
D
D
8
8

OPTIONS
10
LEFT
RIGHT