DoorBird A1122 Series User manual

1
Page 2-17
Installation Manual
IP Access Control Device
Fingerprint
A1122 Series
Seite 18-33
Installationsanleitung
IP Zutrittskontrollgerät
Fingerprint
A1122 Serie
VERSION ., MIN. HW .
A1122
Page 34-49
Manuel d‘installation
Système de contrôle
d‘accès IP Fingerprint
Série A1122
Páginas 50-65
Manual de instalación
Sistema de control
de acceso IP Fingerprint
Serie A1122
Pagina 66-81
Istruzioni per l’installazione
Dispositivo di controllo
dell’accesso IP
Serie A1122

2
INSTALLATION MANUAL
Read these instructions carefully before starting to use
any components. Keep the manual so you can refer
to it at a later date if required. If you hand over the
device to other persons for use, please hand over the
operating manual as well.
You can always find the most up-to-date version of the
installation manual on www.doorbird.com/support
To make things easier we use the term “device” for the
product “IP Access Control Device A1122” and “mobile
device” for a smartphone or tablet.
Liability
Every care has been taken in the preparation of this
document. Please inform Bird Home Automation
GmbH of any inaccuracies or omissions. Bird Home
Automation GmbH cannot be held responsible for any
technical or typographical errors and reserves the right
to make changes to the product and manuals without
prior notice. Bird Home Automation GmbH makes
no warranty of any kind with regard to the content
of this document, including, but not limited to, the
implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH
shall neither be liable nor responsible for incidental
or consequential damages in connection with the
furnishing, performance or use of this material. This
product is only to be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in
strict accordance with the instructions given in
the user documentation. This equipment contains
no components that require service by the user.
Unauthorized equipment changes or modifications
will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Danger: Indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
Warning: Indicates a hazardous situation
which, if not avoided, could result in death or
serious injury.
Caution: Indicates a hazardous situation
which, if not avoided, could result in minor or
moderate injury.
NOTICE Notice: Indicates a situation which, if not
avoided, could result in damage to property.
Important: Indicates significant information
which is essential for the product to function
correctly.
Note: Indicates useful information which
helps in getting the most out of the product.
• Mounting, installation and servicing work on
electrical devices may only be performed by
a qualified electrician. Failure to observe this
regulation could result in the risk of serious
damage to health or fatal injury due to electric
shocks.
• Devices with 110-240 V connection: The device
may only be connected to an easily accessible
power socket outlet. The mains adapter must be
pulled out if a hazard occurs.
• For power supply, only use the original plug-
in mains adapter delivered with the device,
separately available DIN rail power supplies or
a recommended PoE-Switch/PoE-Injector as
specified in this manual.
• Because of electrostatic charging, direct contact
with the circuit board can result in destruction
of the device. Direct contact with the circuit
board must therefore be avoided at any time.
• Observe the EN 60065 resp. EN 60950 resp. EN
62368 standard.
• Do not use the device if there are signs of
damage to the housing, control elements
or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any
doubts, please have the device checked by an
authorized expert.
• Do not open the device. This voids the warranty
of the device. The device does not contain any
parts that can be maintained by the user. In
the event of an error, please have the device
checked by an authorized expert.
• For safety, approval and licensing reasons (CE/
FCC/IC etc.), unauthorized change and/or
modification of the device is not permitted.
• The device is not a toy: do not allow babies and
children to play with it.
• To avoid the danger of suffocation, keep
any packing materials away from babies
and children. Plastic films/bags, pieces of
polystyrene, etc. are not a toy and can be
dangerous in the hands of a child. Discard any
packing materials immediately after removing
the product. Do not reuse packing materials.
• Always lay cables in such a way that they do not
become a risk to people and domestic animals.
• Voltage is applied to parts within the
equipment. Do not touch any parts that are
not associated with the installation, wiring, or
connection. Electric shock could result.
• On devices which are not marked as weather-
proof: Keep the device away from water or any
other liquid.
Hazard information
WARNING

ENGLISH
3
• Do not install or make any wire terminations
while power supply is plugged in. It can cause
electric shock or damage to the device.
• Before turning on power, make sure wires are
not crossed or shorted. If not, fire or electric
shock could result.
• High voltage may be present internally. Do not
open the device. Electric shock could result.
• The device is not of explosion-proof. Do
not install or use near gases or flammable
materials. Fire or explosion could result.
• Do not install two power supplies in parallel
to a single input. Fire or damage to the device
could result. Be sure to connect a single power
supply to the device.
• Do not connect any terminal on the device to
an AC power line. Fire or electric shock could
result.
• Keep AC cord from being marred or crushed.
If the AC cord is fractured, fire or electric shock
could result.
• Do not plug or unplug with wet hands. Electric
shock could result.
• Do not put any metal or flammable material
into the device. Fire, electric shock, or device
trouble could result.
• Existing wiring may contain high voltage AC
electricity. Damage to the device or electric
shock could result. Wiring and installation
must be done by a qualified electrician.
• When mounting the device on a wall or
ceiling, install the device in a convenient
location, but not where it could be jarred or
bumped. Injury could result.
• On devices with ground terminals, connect to
an earth ground. Otherwise fire or malfunction
could result.
• On devices with plastic or real glass, do not put
high pressure on the glass. If fractured, injury
could result.
• On devices with LCD, if LCD is punctured, do
not allow contact with the liquid crystal inside.
Injury could result. If necessary, gargle your
mouth and clean your eyes or skin with clear
water for at least 15 minutes and consult your
doctor.
• Do not put anything on the device or cover
the device with cloth, silicone, glue, coating,
separate covering etc. Fire or device issues
could result.
• Do not install the device in any of the following
locations. Fire, electric shock, or device trouble
could result.
 Places under direct sunlight or places near
heating equipment that varies in temperature.
 Places subject to dust, oil, chemicals, hydrogen
sulfide (hot spring).
 Places subject to moisture and humidity
extremes, such as bathrooms, cellars,
greenhouses, etc.
 Places where the temperature is very low, such
as inside a refrigerated area or in front of an air
conditioner.
 Places subject to steam or smoke (e.g. near
heating or cooking surfaces).
 Where noise generating devices such as
dimmer switches or inverter electrical
appliances are close by.
 Locations subject to frequent vibration or
impact.
• On devices with intercom, be sure to perform
a call test with low audio volume on both
intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.
• If the device does not operate properly, unplug
the power supply.
• All devices which are not marked as weather-
proof are designed for indoor use only. Do not
use outdoor.
• On devices which are marked weather-proof:
Do not spray with high-pressure water. Device
issues could result.
• We do not assume any liability for damage to
property or personal injury caused by improper
use or the failure to observe the hazard
information. In such cases, any claim under
warranty ceases. For consequential damages,
we assume no liability!
WARNING
Safety instructions
• The device shall be used in compliance with
local laws and regulations.
• Store the device in a dry and ventilated
environment.
• Avoid exposing the device to shocks or heavy
pressure.
• Do not install the device on unstable brackets,
surfaces or walls. Make sure the material is
strong enough to support the weight of the
device.
• Use only applicable tools when installing the
device. Using excessive force with tools could
cause damage to the device.
• Do not use chemicals, caustic agents, or
aerosol cleaners.
• Use a clean dry cloth for cleaning.

4
• Use only accessories that comply with
technical specification of the device. These can
be provided by Bird Home Automation GmbH.
• Use only spare parts provided by or
recommended by Bird Home Automation
GmbH.
• Do not attempt to repair the device by yourself.
Contact Bird Home Automation GmbH for
service matters.
• Keep the device more than 1 m (3.3‘) away
from microwave, radio, TV, wireless router and
any other wireless devices.
• On devices with intercom or built-in speaker
or built-in microphone or signal transmission
functions, keep the wires more than 30 cm
(12‘‘) away from AC 100-240 V wiring. AC
induced noise and/or device malfunction
could result.
• Install the device in an area that will be
accessible for future inspections, repairs and
maintenance.
• If the device is used close to a cellular phone, the
device may malfunction.
• The device can be damaged if dropped. Handle
with care.
• The device turns inoperative during power
failure.
• On devices with intercom or built-in speaker or
built-in microphone, in areas where cellular or
Radio / TV broadcasting station antennas are
close by, the device may be affected by radio
frequency interference.
• On devices with LCD screen, it must be noted
in advance that the LCD panel, though
manufactured with very high precision
techniques, inevitably will have a very small
portion of its picture elements always lit or
not lit at all. This is not considered a device
malfunction.
• On devices with intercom, due to the
environmental sound around the device, it
may hinder smooth communication, but this
is not a malfunction.
• On devices with Username/Password, the
Username/Password to access the device is the
customer‘s responsibility. Make sure to use a
password that cannot be easily guessed by a
third party. We recommend that you change
the Password on a regular basis.
• We will, under no circumstances, be liable
for damage that occurs due to failures in
power supply, network equipment or terminal
devices; failures due to Internet providers
and cellular network providers; failures such
as disconnected lines and other losses in
communication, which makes it impossible to
provide this service as well as in any way delay
this service due to any other causes outside of
our responsibility; or if an error or missing data
occurs during transmission.
FCC Caution:
Any Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment. This device complies
with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This
device may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be
colocated or operating in conjunction with any
other antenna or transmitter.
IC Statement
EN: This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
This Class B digital apparatus complies with
Canadian ICES-003.
IC radiation exposure: This equipment complies
with ISEDC radiation exposure limits defined for
a controlled environment. This transmitter must

ENGLISH
5
not be co-located or operated in conjunction
with any other antenna or transmitter.
FR: Le présent appareil est conforme aux CNR
d‘Industrie Canada applicables aux appareils
radio exempts de licence. L‘exploitation est
autorisée aux deux conditions suivantes:
(1) l‘appareil nedoit pas produire de brouillage,
et
(2) l‘utilisateur de l‘appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d‘en compromettre le
fonctionnement.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
IC exposition aux radiations: Cet équipement
est conforme avec ISEDC les limites d‘exposition
aux rayonnements définies pour un contrôlé
environnement. Cet émetteur ne doit pas être
co-localisés ou fonctionner en conjonction avec
une autre antenne ou émetteur.
Transportation
NOTICE When transporting the device, use the original
packaging or equivalent to prevent damage
to the device.
Warranty Information
For information about the device warranty, see
www.doorbird.com/warranty
Information on disposal for users of waste
electrical & electronic equipment (private
household)
This symbol on the products and/or accompanying
documents means that used electrical and electronic
products should not be mixed with general household
waste. For proper treatment, recovery and recycling,
please take these products to designated collection
points, where they will be accepted an a free of charge
basis. Alternatively, in some countries you may be able
to return your products to your local retailer upon the
purchase of an equivalent new product. Disposing
of this product correctly will help to save valuable
resources and prevent any potential negative effects
on human health and the environment which could
otherwise arise from inappropriate waste handling.
Please contact your local authority for further details
of your nearest designated collection point. Penalties
may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
Information on disposal in other countries outside
the European Union
This symbol is only valid in the European Union. If you
wish to discard this product, please contact your local
authorities or dealer and ask for the correct method
of disposal.

6
COMPONENTS*
1x Quickstart guide
with Digital Passport
1x Drilling template 1x Power supply unit
(mains adapter)
with up to four
country-specific
adapters
Small parts
1x Installation manual
1x Flush-mounting
housing
(flush-mounted model)
1x Main Electrical Unit
with front panel
1x Wall-mounting bracket
(surface-mounted model)
1x Disassembly tool
for screw connection
terminal plug
THIS SIDE UP
* The sketches in this manual may differ from the purchased model.
1) Fingerprint reader
2) Dual frequency RFID reader (125 KHz, 13.56 MHz)
3) Bluetooth transceiver
4) Status icons with Diagnostic LEDs
5) Security screw
6) Wiegand jack
7) Screw connection terminal
8) SETUP Button (SET) of the device to e.g.
configure the WiFi interface of the device using
the DoorBird App
The flush-mounted model may differ optically.
DEVICE
Front Back
2
4
1
5
3
1x RJ45 adapter
WIFI
67
8
1x A8005 RFID Key Fob
1x Screw connection
terminal plug

ENGLISH
7
VIDEOS
Need help with the installation? Be sure to watch our
installation videos which can be found on
http://www.doorbird.com/support
Each individual step of the installation is clearly
documented in the videos.
INSTALLATION
All the steps below should be carried out carefully
by a competent adult, taking into consideration
any applicable safety regulations. Please contact us
directly or seek the advice of a competent specialist.
Please ensure that all wires used for the
installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet
connection is at least 0.5 Mbps. The user experience is
only as good as your network speed, network stability
and quality of your network components, such as
your Internet Router and WiFi access points or WiFi
repeaters. Please also make sure that your network
components are no older than two years old, have
been manufactured by a well-known manufacturer,
and have the latest firmware installed.
Should these requirements not be fulfilled, it may
occur that push notifications are delayed or not
delivered to your mobile device.
Requirements:
High-speed Internet (via landline): DSL, cable or optical
fibre
Network: Ethernet, with DHCP
SWITCHING OFF POWER
Switch off the power to all wires leading to
the assembly location, e.g. power supply for
the device or an electrical door opener.
DISMANTLING THE EXISTING
ACCESS CONTROL DEVICE
Should there already be an access control device on
the exterior wall of the house, please remove it.
DETERMINING THE ASSEMBLY
LOCATION
Do not expose the device to direct sunlight.
The housing temperature can exceed the
maximum allowed temperature limit. This can
result in damage of electric and mechanic
components of the device and injuries
especially when touching exterior parts of the
device. White and bright silver-colored front
plates absorb less sunlight than dark ones.
Any defects caused by direct sunlight are not
covered by warranty.
Important note for cavity mounting (e.g. in
pedestals and mailboxes):
To protect the electronic units, please
ensure that the technical components are
protected against dripping and running
water caused by condensate or entering
the mounting space through openings.
To protect the electronic units, ensure
that the mounting space inside is not
accumulating water.
Sucient air circulation must be ensured,
as well as unobstructed drainage of water
at the base of the installation.
Failure to do so will result in warranty being
declined.

8
THIS SIDE UP
. DISASSEMBLING THE FRONT PANEL
Remove the front panel with the attached Main Electrical Unit carefully from the mounting housing (backbox)
using the orange (Torx+Pin) screw driver provided.
We have designed the front panel and the safety screw in a way that it cannot be screwed through the
front panel so that is does not fall off / get lost during installation..
Turn the safety screw counter-clockwise until it is loose. Pull the front panel with attached Main
Electrical Unit out of the mounting housing (backbox).
Flush-mounted model Surface-mounted model
ASSEMBLING THE MOUNTING HOUSING
The product is available as a surface-mounted and flush-mounted version. In the flush-mounted version, the
front panel is slightly larger to better cover the hole in the wall, and the mounting housing (backbox) is made
entirely of metal instead of plastic.
68,00 mm
2.68 in
138,00 mm
5.43 in
26,50 mm
1.04 in
68,00 mm
2.68 in
138,00 mm
5.43 in
26,50 mm
1.04 in
If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains
(gas, water, etc.) are to be found in the wall.
If the wall of the house is made of wood, dowels are not normally required. There are special dowels for
assembling the device on an insulating wall, e.g. Fischer insulating dowels.
If you use the flush-mounted housing, lever up the
wall accordingly.
Flush-mounted model
If the wall of the house is not made of wood, you
should drill dowel holes 5 mm (0.19 in) in diameter
in the wall according to the drilling template and
then place the dowels provided into the boreholes.

ENGLISH
9
. MOUNTING
Lead all cables and wires you want to connect to the device through the mounting housing.
Please make sure that the outer frame of the
flush-mounted housing rests on the outside
of the wall and that the edge of the flush-
mounted housing is sealed all around against
moisture from the outside.
Before mounting: Pierce
through the middle of the
rubber seal for the cable
entry using a screwdriver.
Surface-mounted modelFlush-mounted model
THIS SIDE UP
NETWORK CONNECTION OPTIONS
You can connect the device to the network by either using a WiFi 2.4 GHz
connection or a network cable.
OPTION 
Network cable (recommended, maintenance free)
Install a network cable (which is plugged into a network switch / router
with Internet access) from the inside of your building to the assembly
location. The network cable between the assembly location and the
network switch / router can have a maximum length of 80 m/262 ft (IEEE
802.3). If you must span a distance of more than 80 meters/262 feet you
can put a network switch in between. Make sure to use a high-quality
Cat.5 network cable or better and with proper shielding (Screened Foiled
Twisted Pair (S/FTP or SFTP)) whereby the shield is connected to the outer
metal shield of the RJ45 plug (8P8C).
The device itself does not have an RJ45 socket. The scope of delivery
includes an RJ45 adapter that can be routed out of the housing. As an
alternative, the RJ45 connector of the network cable can be removed
on the device side to connect the wires directly to the Phoenix strip
according to the assignment under point 7 „CONNECTING THE DEVICE“.
OPTION 
WiFI 2.4 GHz
When using WiFi please make sure you have a good WiFi signal at the
assembly location of the device. You can increase the WiFi signal by using
so called “WiFi repeaters”, which can boost your WiFi signal. You should
install such a WiFi repeater close to the assembly location of the device,
typically inside your home and close to the device.
For further information regarding WiFi installations, please visit
www.doorbird.com/wifi
If you have only two wires available at
the assembly location, you may use the
“DoorBird 2-Wire Ethernet PoE Converter
A1071”, sold separately. It allows you to
transfer network data (Ethernet) and
power (PoE) with a simple two-wire
cable over long distances. For example,
existing buildings with a simple two-wire
bell wire can be equipped with network
technology without having to retrofit any
network cables.
For reasons of network stability, we
principally recommend using a network
cable, as WiFi is sensitive to interference
(range, house walls acting as shields, re-
liability of performance, third party WiFi
networks, wireless transmitters causing
interference in the area, etc.).

10
If you must power more than one device
with one power supply , we recommend
to use a PoE-Switch with PoE Standard
IEEE 802.3af Mode A or an appropriate
DIN rail power supply (see “OPTION 3”).
Theoretically (not recommended by us!),
an unshielded, but over the whole length
(max. 80 m/262 ft) twisted bell wire with
two pairs of wires (first twisted pair of
wires: “T+, T-”, second twisted pair of wi-
res “R+, R-”) can be used for the network
and PoE transmission as an alternative
to a Cat.5 network cable or better. This is
comparable to a Cat.3 network cable. In
this case, however, we cannot guarantee
the data throughput or the stability of
the network connection and power sup-
ply; this must be measured and checked
on site by qualified personnel over several
hours (network data is transmitted at
high frequency, therefore a shielded
Cat.5 network cable twisted in pairs or
better must normally be used).
The provided mains adapter is only
capable to power one device. It is not
designed to power multiple devices
simultanously.
If you must power more than one device
with one power supply, we recommend
to use a PoE-Switch with PoE Standard
IEEE 802.3af Mode A or an appropriate
DIN rail power supply (see “OPTION 3”).
PREPARE POWER SUPPLY
The device does not have a battery as power supply, therefore, choose one
of the following options.
OPTION 
Power supply using the power supply unit (mains adapter)
To power the device using the provided mains adapter, 2 insulated wires
are required. The power supply unit has a 300 cm (9.8 ft) long cable with
two insulated wires. The network connection is then established via a
network cable or alternatively via WiFi.
NOTICE Do not plug the power supply unit into the wall socket yet.
Only use the power supply unit provided along with the device,
or a DIN-rail power supply unit (see “OPTION 3”) that you
can obtain from us separately, since this has been specially
stabilized electrically and is equipped with an integrated audio
interference reduction device. Other power supply units may
destroy the device or cause poor transmission quality. The
warranty automatically expires if you use a different power
supply unit.
NOTICE The power supply unit is plugged into a wall socket, usually
where the two wires from your assembly location come out of
the wall in the interior of the house.
The provided mains adapter is not outdoor-ready and for
indoor-use only.
OPTION 
Power supply and network connection using PoE (Power over
Ethernet)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-
Injector (e.g. DoorBird Gigabit PoE Injector A1093), use a CAT.5 cable or
higher in accordance with the PoE standard IEEE 802.3af Mode A.
A CAT.5 cable or higher must be used for this purpose, as network signals
can only be transmitted over completely insulated, shielded and twisted
cables. If you use PoE as a source of power, the four wires for PoE then
simultaneously form the data line. The device will not start if your PoE-
Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af
Mode A.
NOTICE Do not combine the power supply from the power supply unit
(mains adapter) with the power supply via PoE.
You can find further information about PoE here:
http://www.doorbird.com/poe
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.

ENGLISH
11
OPTION 
Power supply using a DIN rail power supply unit
Alternatively to the mains adapter, we offer DIN rail power supplies in our online shop, which can be installed by
a specialist. The network connection is then made via a network cable or alternatively via WiFi.
For easier installation we strongly
recommend to remove the plug from
screw connection terminal while you
connect the cables and wires.
CONNECTING THE DEVICE
It is possible to connect the cables and wires to the device conveniently
and safely via the labeled screw connection terminal. You can connect all
necessary cables and wires to the device now.
NOTICE Please remove any cables and wires from the connection ports
of the device that you do not need.
The product comes with a disassembly tool that allows you to safely
remove the connector from the screw terminal socket. Please do not use
any other tool, e.g. a screwdriver, as this may damage the circuit board
of the device.
LAN / POE
D D GND
Wiegand
R R R R  VDC
– +
T+ T- R+ R-
Port Description
LAN/POE
T+ T- R+ R-
The device does not have an integrated standarized RJ45 socket to ensure ...
• that the device rests as flat as possible on the wall.
• that no wall needs to be levered up.
• that a strong and inflexible Cat.6 or Cat.7 installation cable can be used.
Use only four wires (1, 2, 3 and 6) of a standard Network cable Cat.5 or better,
coming from the Internet Router/PoE-Switch/PoE-Injector.
Cat.5 / Cat.6 Network cable
T+ White and orange network cable wire (Number 1, Transmit Data +)
T - Orange network cable wire (Number 2, Transmit Data -)
R+ White and green network cable wire (Number 3, Receive Data +)
R - Green network cable wire (Number 6, Receive Data -)

12
R1 R1, R2 R2 Bi-stable latching relay #1, max. 24 V DC/AC, 1 A. Security feature: The relay
keeps its state even in the case of loss of power. You can configure the default
state of the relay (open/close) via the DoorBird App. These ports can be used
to connect e.g. an electric door opener. The device does not supply power to
the connected device. The power supply for the electric door opener must be
installed separately.
When wiring an electric door opener directly to the device. There is a
risk that the electric door opener could be tampered by unauthorized
third parties (e. g. by breaking the device and short-circuiting the
wiring of the door opener). Therefore, we generally recommend the
use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door
Controller A1081) for wiring an electric door opener for a more secure
installation in your home.
15 VDC - 15 V DC Power supply input, negative pole (-). Please connect the black wire
of the power supply unit (mains adapter) supplied with this device if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.
15 VDC + 15 V DC Power supply input, positive pole (+). Please connect the red wire of
the power supply unit (mains adapter) supplied with the device here, if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.
D0 Data Low. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output
(data line). Wiegand can be turned on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires (black,
green, white) and plug. Please use this cable to connect your Wiegand device
(D0: Green wire).
D1 Data High. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output
(data line). Wiegand can be turned on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires (black,
green, white) and plug. Please use this cable to connect your Wiegand device
(D1: white wire).
GND Ground. For Wiegand output (RFID reader, Keypad). Wiegand can be turned
on/off and configured via the DoorBird App.
The Small parts bag provided contains a cable with tree individual wires
(black, green, white) and plug. Please use this cable to connect your Wiegand
device (GND: Black wire).
Port Description
LAN/POE
T+ T- R+ R-
Cat.7 Network cable (Installation cable)
T+ White network cable wire from pair “orange/white”
(Number 1, Transmit Data +)
T- Orange network cable wire from pair “orange/white”
(Number 2, Transmit Data -)
R+ White network cable wire from pair “green/white”
(Number 3, Receive Data +)
R- Green network cable wire from pair “green/white”
(Number 6, Receive Data -)
NOTICE Do not power the device simultaneously via the power supply from
the power supply unit (mains adapter) and the power supply via PoE.

ENGLISH
13
NOTICE Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way
may damage the device. Wires without insolation material must not protrude out of the green screw
connection terminal, it may lead to electrical short and damage the device.
ASSEMBLE THE DEVICE TO THE MOUNTNG HOUSING (BACKBOX)
If you use the surface- or flush-mounted version, assemble the front panel with the attached Main Eletrical
Unit carefully using the orange (Torx+Pin) screw driver provided with the wall mounting-bracket / mounting
housing. Turn the safety screw clockwise until it is hand-tight.
NOTICE Tighten the safety screw by hand only (less than 5 newton meter [Nm]), otherwise the Main Eletrical
Unit housing may be damaged.
ACTIVATE THE DEVICE
If the device is to be supplied with power by a mains adapter, plug the power adapter of the device into a wall
socket. If the device is to be powered via PoE, switch on the PoE-Switch/ PoE-Injector which is connected to the
device. If the device is to be powered via DIN-rail power supply, switch on the DIN-rail power supply.
To check if the device is powered, place your finger on the fingerprint sensor and the integrated LED will light up
briefly. In addition, shortly after switching on, you will hear a short acknowledgement tone when the device is
ready. This may last for up to 5 minutes.
If the LED do not light up, please check the power supply. When using a wall-plug power supply and not PoE,
please check whether you have connected the positive pole and negative pole to the device correctly.
The device is ready for operation (booting up process, any software updates, etc.) once it has emitted a short
diagnosis sound (two beeps) from the integrated piezo speaker. This may last for up to 5 minutes.
Surface-mounted modelFlush-mounted model

14
 DOWNLOADING AND INSTALLING
THE APP
Download the “DoorBird” App by Bird Home
Automation onto your mobile device from the Apple
App Store or Google Play Store. You can always find
the most up-to-date version of the App manual on
www.doorbird.com/support
If you use WiFi for connecting the device to your
Internet Router, first go to the DoorBird App > ”WiFi
Setup“ and follow the instructions.
If you have finished the WiFi setup or have connected
the device to your Internet Router by means of a
network cable, go to the DoorBird App > “Add device”
and click on the QR code icon in the “User” field.
Scan the user QR code found on the “Digital Passport”
provided with the device.
If you have problems adding the device to the App
please check if the device is online ( www.doorbird.
com/checkonline ). If the device is not online, please
check the WiFi or network cable connection again.
 HOW TO REGISTER
A NEW FINGERPRINT
Hands-free mode
ghehpf 0001
front door
abcdef 0002
office
Settings
Add
LAN only mode
App security
Administration
WiFi Setup
DEVICES
APP SETTINGS
FURTHER FUNCTIONALITY
Hands-free mode
ghehpf 0001
front door
abcdef 0002
office
Settings
Add
LAN only mode
App security
Administration
WiFi Setup
DEVICES
APP SETTINGS
FURTHER FUNCTIONALITY
1
abcdef0000
●●●●●●●●●●●
abcdef0000
abcdef0001
LOGIN
Administration
Save login
Continue
SAVED ADMIN LOGINS
abcdef0000
●●●●●●●●●●●
abcdef0000
abcdef0001
LOGIN
Administration
Save login
Continue
SAVED ADMIN LOGINS
(Your Admin Login)
2
Settings
History
FINGERPRINT READER
Administration
Einstellungen
Historie
BLE KEYFOB
Einstellungen
PERIPHERIE
HTTP(S) Aufrufe
SIP Nummern
FAVORITEN
Settings
History
FINGERABDRUCKLESER
Administration
Settings
History
BLUETOOTH KEYFOB
Einstellungen
PERIPHERIE
HTTP(S) Aufrufe
SIP Nummern
FAVORITEN
Settings
Add
No fingerprints added
Search
Settings
Add
No fingerprints added
Search
3 4
Fingerprint Save
Name
Validation type
Schedule for actions
Right Thumb
BASICS
VALIDATION
weekly schedule
Bluetooth Keyfob Save
Name My Bluetooth Keyfob
GENERAL
BUTTON CONFIGURATION
Weekly schedule
Weekly schedule
Delete
Button 1
Button 2
5
Enter a name for the
fingerprint and configure
the schedule for actions.
This can be edited later
if needed. Press „Save“
to start the enrollment
process.
Enroll fingerprint
Name
Step 1
Place your finger on the sensor
Follow the instructions
in the DoorBird App
until the enrollment
process is finished.
6
. GENERAL INSTRUCTIONS
• Do not roll or swipe the finger over the sensor.
Try to touch the sensor with as much fingerprint
pattern as possible.
• Try to position the finger in the same way as its
position will be when using the sensor later for
finger recognition.
• If a previously registered finger is not recognized,
save it as an additional new finger (e.g. “right
forefinger 1” and “right forefinger 2”).
• Fingerprint templates are only stored locally
within the Fingerprint reader module and are not
transferred into the main eletrical unit or into the
Cloud.
. HOW TO SOLVE RECOGNITION ISSUES
Use the finger with the greatest
possible contact (e.g. thumb)
and clearest fingerprint pattern.
Small fingers (e.g. children),
fingers without structure or with
scars and other injuries make
recognition dicult.
Clean/Dry the finger before
using the reader. Dirt, wetness
or skin folds on the fingertips
reduce the recognition rate.
Register several fingers
per person. Injuries to the
fingerprint could prevent
the detection (e.g. torn skin,
scars).
Register the same finger for
summer and winter.
Various weather conditions
(summer, winter, heat, cold ...)
could change the fingerprint
and lead to nonrecognition. If a
previously registered finger is not
recognized, save it as an additional
new finger (e.g. “right forefinger
winter” and “right forefinger
summer”).
5
43
2
1

ENGLISH
15
DIAGNOSTIC-LED MAINTENANCE FOR DOORBIRD PRODUCTS
Cleaning and maintenance instructions
All DoorBird door stations are made of high-quality
materials and are designed for a durable lifetime.
Since door stations are usually installed in unprotected
outdoor areas, they are exposed to adverse weather
conditions and aggressive substances, especially close
to frequently used roads, in coastal and industrial
areas. Therefore please consider the following care
instructions. Unfortunately, we cannot accept any
liability for damage if these instructions are not being
observed.
Aggressive dirt such as bird droppings should be
removed as quickly as possible.
NOTICE Never use abrasive detergents such as steel
wool or scouring milk!
Warm water is usually sucient, if necessary with
a little detergent, a soft cloth or brush. Plastic parts
(camera or name tags) must not be treated with
metal care products. Remove all residues of cleaning
agents or lubricants to avoid stains or discolouration
after the maintenance.
Stainless Steel
Only high-quality German stainless steel is used for all
available DoorBird door stations. However, high-quality
stainless steel can also rust, as approx. 70% of stainless
steel is made of iron. Rust resistance is only achieved
by a protective layer (also called passive layer), which
covers the iron like a skin. This protective layer consists
essentially of chromium and other precious metals.
Iron particles, grinding dust and chips deposited on
stainless steel can lead to corrosion (rust film). These
iron particles can be found everywhere, but especially
in coastal and industrial areas and close to frequently
used roads. Please remove ferrous deposits immediately,
as they will attack your door station and lead to real
rust if not removed. To remove rust, simply wipe off the
dust; in addition, a care product is recommended, e.g.
WD 40, available e.g. at Amazon for less than € 5.00.
Simply apply in a thin layer and rub in. The same applies
if rust appears on the engravings on the stainless steel
surface.
Cement or lime splashes should be carefully removed
as soon as possible with a wooden spatula before
hardening.
The following cleaning detergents are not to be used
as they reduce corrosion resistance:
• products containing chloride and hydrochloric
acid
• Bleach (in case of accidental use, rinse thoroughly
with water)
• Silver polish
DIAGNOSTIC SOUNDS
The device may emit brief diagnostic sounds after
it has been connected to power supply / network /
Internet, e.g. upon boot process finished, press of a key,
WiFi Setup Mode enabled, RFID Reader detected tag,
Relay triggered.
TAMPER SENSOR
The device has a built-in tamper sensor that can
be configured via the app to send an alert over the
network (e.g. a push notification) if the device is
moved during operation.
BLUETOOTH TRANSCEIVER
The device has a built-in Bluetooth® transceiver.
Compatible with the DoorBird Bluetooth Keyfob
Remote A8007.
DOORBIRD CONNECT
The device features many options to integrate it into
third-party applications. For information, terms and
conditions see www.doorbird.com/connect
Door Opener and RFID LED
Red:
Rejected
Purple: Rejected
(too many attempts,
please wait 30 seconds
and try again)
Red: Rejected Green: Authorized
Fingerprint LED
Green:
Authorized

16
After the cleaning with clear water wipe with damp
cloth and rub dry to avoid lime traces. Lime residues
can be avoided by using demineralised water.
Stainless steel PVD coated
PVD coated, chrome-plated or gold-plated surfaces
are recommended to be cleaned with a grease-
dissolving detergent and clear water or with a clean
and dust-free microfibre cloth. For high-gloss surfaces,
use a scratch-free cloth (e.g. cleaning cloth for glasses,
furniture polishing cloth, etc.).
Lacquered surfaces
Clean painted surfaces and lettering with a soft,
scratch-free cloth moistened with a mild soap solution
(e.g. cleaning cloth for glasses, furniture polishing cloth,
etc.). To prevent stains or discolouration, the detergents
should be wiped off without leaving any residue.
Be particularly careful with lettering in order not to
damage the film or the print.
Real burnished brass and architectural bronze
The surface finish „real burnished brass“ and
„architectural bronze“ is a cold burnished finish, which
is sealed with a boat wax. As the surface is open to
diffusion, it is advisable to apply a subsequent layer of
wax at intervals (approx. 6-18 months) using a soft cloth
(flow cloth), allow it to soak in for a while and then rub
it evenly dry with a dry cloth. We recommend a wax
such as Teroson WX 990 by Henkel.
Chemical cleaning agents of any kind mustNOTbe
used.
Avoid touching the surface with your fingers during
installation. Wearing powder-free latex gloves is
recommended.
Depending on the weather conditions, the processed
surface may change, forming its characteristic,
individual appearance.

ENGLISH
17
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird Home Automation
GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch,
iOS, iPhone and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are registered trademarks
of Bluetooth SIG, Inc.
5. All other company and product names may be trademarks of the
respective companies with which they are associated.
6. We reserve the right to make changes to our products in the
interests of technical advancement. The products shown may
also look different from the products supplied based on ongoing
enhancement.
7. Reproducing or using texts, illustrations and photos from this
instruction manual in any media – even if only in the form of
excerpts – shall only be permitted with our express written
consent.
8. The design of this manual is subject to copyright protection. We
do not accept any liability for any errors or any erroneous content
or printing errors (even in the case of technical specifications or
within graphics and technical sketches).
9. Our products are in compliance with all technical guidelines,
electrical and telecommunications regulations applicable in
Germany, the EU and the USA.
10. Our products and also the components contained therein
(ICs, software, etc.) may only be used for civilian non-military
purposes.
Data privacy and data security
1. For maximum security, the device uses the same encryption
technologies as are used in online banking. For your security, no
port forwarding or DynDNS is used either.
2. The data centre location for remote access over the Internet by
means of an App is obligatory in the EU if the determined Internet
IP-Address location of the device is within the EU. The data centre
is operated in line with the most stringent security standards.
3. Video, audio and any other surveillance methods can be regulated
by laws that vary from country to country. Check the laws in your
local region before installing and using this device for surveillance
purposes.
If the device is a door-, indoor station or camera:
• In many countries video and voice signal may only be transmitted
once a visitor has rung the bell (data privacy, configurable in the
App).
• Please carry out the mounting in such a way that the detection
range of the camera limits the device exclusively to the immediate
entrance area.
• The device may come with a visitor history and motion sensor. You
can activate/deactivate this function if required.
If necessary, indicate the presence of the device in a suitable place
and in a suitable form.
Please observe any relevant country-specific statutory regulations
concerning the use of surveillance components and surveillance
cameras applicable at the installation site.
Check with the property owner and your house community if you are
allowed to install and use this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or miss-configuration of
this product, including the unauthorized opening of a door.
Bird Home Automation cannot be held responsible for damages
caused by improper existing installations or improper installation.
Software and operating system’s updates (so-called “firmware
updates”) are generally automatically installed on the products of
Bird Home Automation GmbH via Internet, if technically possible.
Automatic firmware updates keep the products‘ software up to date
so that they always work reliably, safely and efficiently. Through
further development, features can be added, extended or slightly
changed. Major changes or limitations to existing features will
generally occur if Bird Home Automation GmbH deems it necessary
(e.g. for data protection, data security or stability reasons, or to keep
them up to date). When a firmware update is available, Bird Home
Automation GmbH‘s servers generally automatically distribute it to
all compatible products connected to the Internet or Bird Home
Automation GmbH‘s servers. This process is gradual and can take
several weeks. As soon as a product receives a firmware update, the
system will be installed and will restart by itself. Installed firmware
updates cannot be undone. Since the products and software of
Bird Home Automation GmbH are not explicitly customer-specific
products, a customer cannot deny an automatic update if the
product is connected to the Internet or to the Bird Home Automation
GmbH’s server.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: [email protected]
It is possible that these manual still contains typographical errors
or printing errors.The information in this manual will be checked
regularly and corrections will be made in the next version. We accept
no liability for errors of a technical or printing nature and their
consequences.

FCCCaution
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe
followingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)
thisdevicemustacceptanyinterferencereceived,includinginterferencethatmay
causeundesiredoperation.
AnyChangesormodificationsnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheuser'sauthoritytooperatetheequipment.
Note: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClass
Bdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedto
providereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.
Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnot
installedandusedinaccordancewiththeinstructions,maycauseharmfulinterference
toradiocommunications.However,thereisnoguaranteethatinterferencewillnot
occurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferenceto
radioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoff
andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthe
followingmeasures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparationbetweentheequipmentandreceiver.
-Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe
receiverisconnected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforan
uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwith
minimumdistance20cmbetweentheradiator&yourbody.

ICCaution:
ThisdevicecomplieswithIndustryCanadaslicence-exemptRSSs.Operation issubjecttothe
followingtwoconditions:
(1)Thisdevicemaynot causeinterference;and
(2)Thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesired
operation of thedevice.
Tomaintain compliancewithRFexposureguidelines,thisequipmentshould beinstalledand
operatedwitha minimum distanceof 20cm betweentheradiatorand yourbody.
Leprésentappareil estconformeauxCNRd'IndustrieCanada applicablesaux appareilsradio
exempts delicence.L'exploitation estautoriséeaux deuxconditionssuivantes:
(1) l'appareil nedoit pasproduiredebrouillage,et
(2) l'utilisateurdel'appareil doitacceptertoutbrouillageradioélectriquesubi,mêmesile
brouillageestsusceptibled'encompromettrelefonctionnement.
Pourmaintenirla conformitéaux directivesd'expositionaux radiofréquences, cet équipement
doit être installéetutiliséavecunedistanceminimalede20cm entreleradiateuretvotrecorps.