Dorel Asia DA1010-1 User manual

DA1010-1 (WHITE)
(TAKEN FROM CARTON)
_____________________________________
Date of purchase:
_______ / _______ / _______
THIS INSTRUCTION BOOKLET
CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
Lot number:
6-Drawer Dresser
UPC CODE:
0-65857-17154-9
NOTE:
DOREL ASIA
Model No:
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel #: [phone]
E-Mail: [email protected]om
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage
finish. Excessive exposure to sunlight and extreme changes in temperature and moisture
can damage wood furniture.
MAINTENANCE
Check bolts/screws periodically and tighten them if necessary.
LIMITED WARRANTY
Dorel warrants its product to be free from defects in material and workmanship and agrees
to remedy any such defect. This warranty covers 1 year from the date of original purchase.
This warranty is valid only upon presentation of proof of purchase. This is solely limited to
the repair or replacement of defective furniture components and no assembly labor is
included. This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or repaired in any way.
This warranty gives you specific legal rights and you may also have other rights which vary
from State to State.
WARNING: Should this product become damaged, and/or
components are broken or missing, DO NOT USE.
* Unless specifically designed to accommodate, do not set TVs or other heavy objects on
top of this product.
* Never allow children to climb or hang on drawers, doors or shelves.
* Never open more than one drawer at a time.
* Do not defeat or remove the drawer interlock system.
* Use of tipover restraints may only reduce, but not eliminate, the risk of tipover.
CARE AND CLEANING
* To avoid unnecessary damage, when levelers have been extended, DO NOT drag across
surface when moving. Be sure to lift and carry the item to its location.
* Estimated assembly time: 60 minutes.
WARNING
Serious or fatal crushing injuries can occur from furniture tipover. To help prevent
tipover:
* Install tipover restraint provided.
* Place heaviest items in the lower drawers.
* Assemble on a soft, smooth surface to prevent damage to the product finish.
* Use the wall safety strap provided to secure the unit to the wall.
* A Phillips head screw driver is not included.
* DO NOT use power tools.
* CAUTION: Adult assembly required.
* Assembly will require two people.
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
E-MAIL: [email protected]
NOTES
* Ensure all parts and components are present before beginning assembly.
CUSTOMER SERVICE
If you have any questions about this product, contact our customer service representative
first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product
model number, color and a detailed description of the part.
Customer Service Department No. 413

HARDWARE LIST
1 2 3
4 5 6
7 8 9
10 11 12
13 14
ALLEN KEY
1 PC
SAFETY STRAP
1 KIT
SMALL BOLT
6 PCS
LARGE BOLT
1 PC
Ø5/32" X 7/8"
Ø1/4" X 35 mm
SMALL WOOD DOWEL
20 PCS
LARGE WOOD DOWEL
23 PCS
ROUND HEAD SCREW
14 PCS
FLAT HEAD SCREW
28 PCS
SMALL CAM LOCK
24 PCS
Ø3 X 15 mm
6-Drawer Dresser
DA1010-1
KNOB
6 PCS
Ø4 X 25 mm
Ø8 X 30 mm
Ø6 X 20 mm
Ø7 X 36 mm
Ø13 X 10 mm
LARGE CAM BOLT
18 PCS
ADJUSTABLE LEVELER
3 PCS
Ø15 X 11 mm
LARGE CAM LOCK
18 PCS
Ø7 X 28 mm
SMALL CAM BOLT
24 PCS
Ø1/4"

PARTS LIST
A B C
D E F
G H I
J K L
BACK BOTTOM PANEL
1 PC
SMALL DRAWER LEFT SIDE
2 PCS
SMALL DRAWER RIGHT
SIDE
2 PCS
6-Drawer Dresser
DA1010-1
RIGHT SIDE FRAME
1 PC
TOP PANEL
1 PC
LEFT SIDE FRAME
1 PC
LARGE DRAWER RIGHT
SIDE
4 PCS
SMALL DRAWER BACK
2 PCS
LARGE DRAWER LEFT SIDE
4 PCS
MIDDLE PANEL
1 PC
TOP RAIL
2 PCS
FRONT BOTTOM RAIL
1 PC

PARTS LIST
M N O
P Q R
S T U
V
SUPPORT PANEL
1 PC
LEFT BOTTOM DRAWER
FRONT
1 PC
RIGHT BOTTOM DRAWER
FRONT
1 PC
BACK PANEL
1 PC
RIGHT TOP DRAWER
FRONT
1 PC
LEFT MIDDLE DRAWER
FRONT
1 PC
RIGHT MIDDLE DRAWER
FRONT
1 PC
DRAWER BOTTOM
6 PCS
LARGE DRAWER BACK
4 PCS
LEFT TOP DRAWER FRONT
1 PC
6-Drawer Dresser
DA1010-1

STEP 1
6-Drawer Dresser
DA1010-1
Insert large cam bolts (4) into the front bottom rail (F), back bottom panel (G), left side
frame (B) and right side frame (C) as shown.

STEP 2
6-Drawer Dresser
DA1010-1
Insert large cam locks (3) into the middle panel (D) as shown.
Attach rails (E & F) and back bottom panel (G) to the middle panel (D) with large wood
dowels (1) as shown below.
Secure rail (F) and back bottom panel (G) to the middle panel (D) by rotating the large
cam locks (3) on middle panel (D) 1/2 turn clockwise using a Phillips head screwdriver
(not included).

STEP 3
6-Drawer Dresser
DA1010-1
Insert large wood dowels (1) into the left side frame (B).
Insert large cam locks (3) into the top rails (E), front bottom rail (F) and back bottom panel (G).
Secure the left side frame (B) to the assembled unit by rotating large cam locks (3) on the top
rails (E) front bottom rail (F) and back bottom panel (G) 1/2-turn clockwise using a Phillips head
screwdriver (not included).
Install the adjustable leveler (12) to the left side frame (B) as shown.

STEP 4
6-Drawer Dresser
DA1010-1
Insert large wood dowels (1) into support panel (V). Attach support panel (V) to the assembled
unit as shown.
Secure the support panel (V) to the middle panel (D) with large bolt (11) as shown. Use Allen
key (13) to tighten the bolt.
Install the adjustable leveler (12) to the support panel (V) as shown.

STEP 5
6-Drawer Dresser
DA1010-1
Insert large wood dowels (1) into the right side frame (C).
Insert large cam locks (3) into the rails (E & F) and back bottom panel (G).
Secure the right side frame (C) to the assembled unit by rotating cam locks (3) on the top rails
(E), front bottom rail (F) and back bottom panel (G) 1/2-turn clockwise using a Phillips head
screwdriver (not included).
Install the adjustable leveler (12) to the right side frame (C) as shown.

STEP 6
6-Drawer Dresser
DA1010-1
Insert large cam bolts (4) into the top panel (A).

STEP 7
6-Drawer Dresser
DA1010-1
Insert large wood dowels (1) into the left side frame (B), middle panel (D) and right side
frame (C) as shown below.
Insert large cam locks (3) into the side frames (B & C) and middle panel (D).
Place the top panel (A) on the assembled unit.
Rotate large cam locks (3) on the side panels (B & C) and middle panel (D) 1/2-turn
clockwise to secure the top panel (A).
Further secure top panel (A) with flat head screws (8) through rails (E) and middle panel
(D). Use a Phillips head screwdriver (not included) to tighten the screws.

STEP 8
6-Drawer Dresser
DA1010-1
Attach back panel (U) to the assembled frame with round head screws (7).
Use a Phillips head screwdriver (not included) to tighten the screws.

STEP 9
6-Drawer Dresser
DA1010-1
Insert small cam bolts (6) and small wood dowels (2) into the left top drawer front panel
(O).
Insert small cam locks (5) into the small drawer left side (H) and small drawer right side (I).
Attach drawer sides (H & I) to the left top drawer front panel (O). Secure the drawer sides
(H & I) by rotating small cam locks (5) 1/2-turn clockwise using a Phillips head screwdriver
(not included).
Slide the drawer bottom (M) into the grooves of drawer sides (H & I) and left top drawer
front panel (O).

STEP 10
6-Drawer Dresser
DA1010-1
Attach small drawer backs (J) to the drawer sides (H & I) with flat head screws (8).
Use a Phillips head screwdriver (not included) to tighten the screws.
Attach knobs (9) into the left top drawer front panel (O) with bolts (10).
Use a Phillips head screwdriver (not included) to tighten the bolts.
Repeat steps 9 and 10 to assemble the right top drawer using right drawer front (P).

STEP 11
6-Drawer Dresser
DA1010-1
Insert small cam bolts (6) and small wood dowels (2) into the left middle drawer front
panel (Q).
Insert small cam locks (5) into the large drawer left side (K) and large drawer right side
(L).
Attach large drawer sides (K & L) to the left middle drawer front panel (Q). Secure the
drawer sides by rotating small cam locks (5) 1/2-turn clockwise using a Phillips head
screwdriver (not included).
Slide the drawer bottom (M) into the grooves of large drawer sides (K & L) and left middle
drawer front panel (Q).

STEP 12
6-Drawer Dresser
DA1010-1
Attach large drawer backs (N) into the drawer sides (K & L) with flat head screws (8).
Use a Phillips head screwdriver (not included) to tighten the screws.
Attach knobs (9) to the left middle drawer front panel (Q) with bolts (10).
Use a Phillips head screwdriver (not included) to tighten the bolts.
Repeat steps 11-12 to assemble the other drawers using right drawer fronts (R,S and
T).

STEP 13
6-Drawer Dresser
DA1010-1
Insert all drawers into the assembled unit as shown.

That's it! You've finished assembling your 6-drawer dresser!
DA1010-1
6-Drawer Dresser
CAUTION: This unit is intended for use only with the
products and/or maximum weights indicated. Use with other
products and/or products heavier than the maximum weights
indicated may result in instability or cause possible injury.
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel #: [phone]
E-Mail: [email protected]
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

Furniture Wall Safety Strap
A B C D
TOOLS NECESSARY: RUBBER MALLET AND PHILLIPS SCREW DRIVER ARE NOT INCLUDED.
NOTE: 3/8" DRILL BIT AND ELECTRIC DRILL ARE NOT PROVIDED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE
USING THIS PRODUCT AND KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, PLEASE
CALL OUR CUSTOMER SERVICE NUMBER: 1-800-295-1980.
Step 1:
Step 2:
ATTACH A MOUNTING BRACKET (A) SECURELY TO THE BACK EDGE OF THE FURNITURE USING THE SHORT SCREW (D),
THROUGH THE SMALLER HOLE
PLACE THE FURNITURE INTO POSITION SO BOTH MOUNTING BRACKETS ARE VERTICALLY IN LINE. LACE THE END OF THE
SAFETY WALL STRAP (B) THROUGH THE LARGER HOLE IN EACH MOUNTING BRACKET (A). BRING BOTH ENDS TOGETHER AND
SLIDE THE FLAT END THROUGH THE LOCKING END AND DRAW IT THROUGH UNTIL ALL SLACK IS REMOVED.
CONFIRM THAT THE STRAP IS SECURELY LACED AND LOCKED.
Step 3:
Step 4:
LOCATE THE OTHER MOUNTING BRACKET (A) ON THE WALL OVER A WALL STUD AND 2 INCHES BELOW THE MOUNTING
BRACKET SECURED TO THE BACK OF YOUR UNIT. ATTACH TO THE WALL STUD USING THE LONG SCREW (C) PROVIDED,
THROUGH THE SMALLER HOLE.
TO MOVE THE FURNITURE AFTER THE SAFETY WALL STRAP HAS BEEN INSTALLED, SIMPLY
REMOVE THE SCREW FROM THE WALL TO LOOSEN THE SAFETY WALL STRAP.
MOUNTING BRACKET
4 PCS
WARNING: WHEN UPRIGHT, IT IS POSSIBLE THAT THE
FURNITURE MAY TIP OVER. PLEASE INSTALL THE SAFETY
WALL STRAP BEHIND THE FURNITURE TO ENSURE SAFETY.
SHORT SCREW
2 PCS
LONG SCREW
2 PCS
SAFETY WALL STRAP
2 PCS
AB
Email:[email protected]
AB