Dorel 5991196COMUK User manual

B345991096COMUK00UD
Do Not Return This Product!
Contact our customer service team for help first
Call: 01942 524100 (toll free)
email: [email protected]
–Unit can p over causing severe injury or death.
–Anchor unit to stud in wall (if instructed to)
–Do not allow children climb on unit
–Put heavy items on lower shelves or drawers
5991096COMUK
Gentleman's Chest
Date of Purchase: ____/____/_____
Lot Number:
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
WARNING
Easy Tough
Assembly Diculty Meter

Helpful Hints
Do NOT return this product!
Contact our friendly customer service team rst for help
Call us!
01942 524100
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR
[email protected]
2
- Open your item in the area you plan to keep it for less heavy liing
- Idenfy, sort and count the parts before aempng assembly
- Compression dowels are tapped in with a hammer
- Slides are labeled with a R (right) and L (le) for proper placement
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge
- Use all the nails provided for the back panel and spread them out equally
- Back Panel must be used to make sure your unit is sturdy
- Do NOT use harsh chemicals or abrasive cleaners on this item
- Never push, pull, or drag your furniture

Before You Start
Cam Lock Fastening System
3
P
P
P
P
P
This Cam Lock Fastening System will be used throughout the assembly process.
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Cauon: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is ght.
Failure to do so may result in stripping the screw.
Quick
Tip
Assembly
1
3
2
4

Board Identfcaton
Not actual size
4
x1
T5991196010UD
TOP PANEL
x1
T5991196020UD
LEFT SIDE PANEL
x1
T5991196030UD
RIGHT SIDE PANEL
x1
T5991196050UD
PARTITION
x1
T5991196040UD
BOTTOM PANEL
x5
T5991196080UD
DRAWER FRONT
x5
T5991196060UD
LEFT DRAWER SIDE
x5
T5991196070UD
RIGHT DRAWER SIDE
1
4
8
6
7
2 3
5
x5
T5991196090UD
DRAWER BACK
9

Board Identfcaton
Not actual size
5
10
x1
T5991196180UD
FRONT SUPPORT
18
x4
T5991196120UD
LEG
12
x4
T5991196160UD
SHELF
13
x2
T5991196110UD
SIDE RAIL
11
x1
T5991196170UD
CENTER LEG
17
x2
T5991196130UD
FRONT & BACK RAIL
16
x1
T5991196150UD
BACK PANEL
15
x1
T5991196140UD
DOOR
14

Part List
Actual Size
6
x12
TUD0010
PH M4 X 18
x21
TUD0006
NAIL
x36
TUD0001
Cam Bolt
x31
TUD0009
CBS 4 x 38
x36
TUD0002
Cam Lock
15-12
x22
TUD0004
DOWEL 8 X 25
x80
TUD0008
CBS 3.5 x 16
x16
TUD0018
SHELF HOLDER
x2
TUD0020
L-BRACKET
Hardware Bag Reference Number:
25991196COM0UD

Part List
Not Actual Size
7
x1 set
TUD0021
ANTI TIPPING KIT
x5 SET
TUD0016
DRAWER SLIDE 12“
x6
TUD0012
HANDLE
x2 SET
TUD0019
SLIDING ROLLER
Hardware Bag Reference Number:
25991196COM0UD

8
* raw edges are shaded
Step 1
x6
TUD0001
1
x1 SET
TUD0021
Insert Cam Bolt and fully ghten it.
Fix an-pping kit, do not fully ghten in this step

9
* raw edges are shaded
Step 2
12
x4
x8
TUD0001
Insert Cam Bolt and fully ghten it.

10
Proper orientation of CAM LOCK
Tip
Assembly
Quick
* raw edges are shaded
Step 3
11
18
x10
TUD0002
x10
TUD0004
x2
Please ensure direcon of Cam lock
13
x2

11
* raw edges are shaded
Step 4
x2
TUD0010
x1
TUD0012
14
x2 SET
TUD0019
x16
TUD0008
Install sliding roller & handle.

12
* raw edges are shaded
Step 5
11
12
12
x2 SET
Fix legs to side rail by ghten the Cam Lock

13
* raw edges are shaded
Step 6
13
13
11
Fix front rail & back rail by ghten the Cam
Lock

14
* raw edges are shaded
Step 7
13
11
Fix side rail by ghten the Cam Lock

15
* raw edges are shaded
Step 8
13
4
x4
TUD0009
Fix boom panel by using screw.

16
* raw edges are shaded
Step 9
4
x4
TUD0008 x2
TUD0020
Secure boom panel installaon by using screw & L-Bracket.

17
* raw edges are shaded
Step 10
17
x1
TUD0009
Aach center leg.
4

18
Proper orientation of CAM LOCK
Tip
Assembly
Quick
* raw edges are shaded
Step 11
x4
TUD0004
x2
TUD0002
2
x8
TUD0018
Preparaon of le side panel

19
* raw edges are shaded
Step 12
x5 (CL)
TUD0016
5
x15
TUD0008
LEFT FACE
x1
TUD0001
Screw Posion
Preparaon of paron panel
x2
TUD0002

20
Proper orientation of CAM LOCK
Tip
Assembly
Quick
* raw edges are shaded
Step 13
x4
TUD0004
5
RIGHT FACE
x8
TUD0018
Preparaon of paron panel