Dorner AquaGard 7350 Series User manual

For other service manuals visit our website at:
www.dorner.com/service_manuals.asp
DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA
P.O. Box 20 • 975 Cottonwood Ave. TEL: [phone] TEL: [phone]
Hartland, WI 53029-0020 USA FAX: [phone] FAX: [phone]
851-679 Rev. C
7350 Series Side Mount 90°
Drive Package
Installation, Maintenance & Parts Manual
US Version CE Version

Dorner Mfg. Corp. 2 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Table of Contents
Introduction ......................................................................... 2
Warnings - General Safety .................................................. 3
Product Description............................................................. 4
Specifications ...................................................................... 4
Gearmotor Mounting Package Models:........................... 4
Table 1: Gearmotor Specifications .................................. 5
US Version................................................................... 5
CE Version................................................................... 5
Table 2: Belt Speeds for
Fixed Speed 90° Painted Gearmotors.............................. 5
US Version................................................................... 5
CE Version................................................................... 5
Table 3: Belt Speeds for
Variable Speed 90° Painted Gearmotors ......................... 6
US Version................................................................... 6
CE Version................................................................... 6
Table 4: US Version Belt Speeds for
Fixed Speed 90° Stainless Gearmotors............................ 6
Table 5: US Version Belt Speeds for
Variable Speed 90° Stainless Gearmotors ....................... 6
Installation............................................................................ 7
US Version Side Drive Package....................................... 7
Required Tools.............................................................. 7
CE Version Side Drive Package....................................... 9
Required Tools.............................................................. 9
Preventive Maintenance and Adjustment .......................... 11
Required Tools ............................................................... 11
Check List....................................................................... 11
US Version Gear Reducer Replacement ........................ 11
US Version Motor Replacement .................................... 12
CE Version Gearmotor Replacement............................. 14
Service Parts....................................................................... 15
US Version Side Mount Drive Package for
90° Gearmotors............................................................... 15
CE Version Side Mount Drive Package for
90° Gearmotors............................................................... 16
US Version Gearmotor Assembly.................................. 17
CE Version Gearmotor Assembly.................................. 18
Notes .................................................................................. 19
Return Policy...................................................................... 20
Introduction
Upon receipt of shipment:
• Compare shipment with packing slip. Contact factory
regarding discrepancies.
• Inspect packages for shipping damage. Contact carrier
regarding damage.
• Accessories may be shipped loose. See accessory instruc-
tions for installation.
Dorner’s Limited Warranty applies.
Dorner reserves the right to make changes at any time
without notice or obligation.
Dorner has convenient, pre−configured kits of Key Service
Parts for all conveyor products. These time saving kits are
easy to order, designed for fast installation, and guarantee
you will have what you need when you need it. Key Parts
and Kits are marked in the Service Parts section of this
manual with the Performance Parts Kits logo.
IMPORTANT
Some illustrations may show guards
removed. DO NOT operate equipment
without guards.

851-679 Rev. C 3 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Warnings - General Safety
A
WARNING
The safety alert symbol, black triangle with
white exclamation, is used to alert you to
potential personal injury hazards.
A
DANGER
Climbing, sitting, walking or riding on
conveyor will cause severe injury.
KEEP OFF CONVEYORS.
A
DANGER
DO NOT OPERATE CONVEYORS IN AN
EXPLOSIVE ENVIRONMENT.
A
WARNING
Exposed moving parts can cause severe
injury.
LOCK OUT POWER before removing guards
or performing maintenance.
A
WARNING
Gearmotors may be HOT.
DO NOT TOUCH Gearmotors.
A
WARNING
Exposed moving parts can cause severe
injury.
REPLACE ALL GUARDS BEFORE RUNNING
CONVEYOR.
A
WARNING
Dorner cannot control the physical
installation and application of conveyors.
Taking protective measures is the
responsibility of the user.
When conveyors are used in conjunction
with other equipment or as part of a multiple
conveyor system, CHECK FOR POTENTIAL
PINCH POINTS and other mechanical
hazards before system start-up.

Dorner Mfg. Corp. 4 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Product Description
Refer to (Figure 1) for typical gearmotor assembly
components.
Figure 1
Figure 1
Specifications
Gearmotor Mounting Package Models:
1Conveyor
2 Mounting Bracket
3 Motor
4 Gear Reducer
1
2
34
D
A
735
28
A
M
Drive Position
Gearmotor Size
Gearmotor Type
Language
Conveyor Sprocket
S
Drive Type
128
S
Gearmotor Sprocket
M = US Version
U = CE English Version

851-679 Rev. C 5 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Specifications
Table 1: Gearmotor Specifications
US Version
CE Version
Table 2: Belt Speeds for Fixed Speed 90° Painted Gearmotors
US Version
(vp) = voltage and phase
11 = 115/208-230, 1-phase
23 = 0.5 HP – 230/460 V, 3-phase
1.0 & 1.5 HP – 208-230/460 V, 3-phase
CE Version
Singe Phase Three Phase
Output Power 0.50 hp (0.37 kW) .50 hp (.37 kW) /1 hp (.74 KW) / 1.5 hp (1.11 kW)
Input Voltage 115 V.A.C. 208 - 230 / 460 V.A.C.
Input Frequency 60Hz 6 - 60 Hz
Motor RPM 22 - 44 22 - 233
Gearmotor Ratios 5:1, 7:1, 10:1, 15:1, 20:1, 30:1, 40:1, 60:1, 80:1
Frame Size NEMA 56C
Motor Type Totally Enclosed, Non-ventilated
(Except 1.5 hp Stainless Steel Gearmotor = Totally Enclosed, Fan Cooled)
Fixed Speed Variable Speed
Output Power 0.37 kW to 1.5 kW
Input Power 230 / 400 V 3 Phase
Input Frequency 50 Hz 12 - 80 Hz
Gearmotor Ratios 60:1, 30:1, 25:1, 15:1, 10:1, 7.5:1, 5:1
Motor Type Totally Enclosed, Fan Cooled
Part Number Belt Speed RPM 1 Phase 3 Phase in-lbs N-m
Ft/min M/min HP Kw FLA HP Kw FLA
74M080HS4(vp)FN 22 6.7 22 0.5 0.37 6.8/3.7-3.4 0.5 0.37 1.6/0.8 356 40.2
74M060HS4(vp)FN 29 8.8 29 0.5 0.37 6.8/3.7-3.4 0.5 0.37 1.6/0.8 442 49.9
74M040HS4(vp)FN 44 13.2 44 0.5 0.37 6.8/3.7-3.4 0.5 0.37 1.6/0.8 486 54.9
74M030HS4(vp)FN 58 17.7 58 N/A N/A N/A 1 0.74 3.5-3.2/1.6 487 55.0
74M020HS4(vp)FN 87 26.5 87 N/A N/A N/A 1 0.74 3.5-3.2/1.6 407 46.0
74M015HS4(vp)FN 117 35.7 117 N/A N/A N/A 1 0.74 3.5-3.2/1.6 470 53.1
74M010HS4(vp)FN 175 53.3 175 N/A N/A N/A 1.5 1.11 4.6-4.2/2.1 442 49.9
74M007HS4(vp)FN 233 71.0 233 N/A N/A N/A 1.5 1.11 4.6-4.2/2.1 360 40.7
Part Number Belt Speed FLA N-m
Ft/min M/min RPM kW Volts Phase at 230V at 400V
73U060HS423FN 23 7.0 23 0.37 230/400 3 1.91 1.1 81
73U030HS423FN 46 14.0 46 0.75 230/400 3 3.65 2.1 102
73U025HS423FN 55 16.8 55 0.75 230/400 3 3.65 2.1 94
73U015HS423FN 93 28.3 93 1.12 230/400 3 4.89 2.81 89
73U010HS423FN 140 42.7 140 1.12 230/400 3 4.89 2.81 64
73U007HS423FN 186 56.7 186 1.49 230/400 3 6.17 3.55 67
73U005HS423FN 279 85.0 279 1.49 230/400 3 6.17 3.55 46

Dorner Mfg. Corp. 6 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Specifications
Table 3: Belt Speeds for Variable Speed 90° Painted Gearmotors
US Version
CE Version
Table 4: US Version Belt Speeds for Fixed Speed 90° Stainless Gearmotors
Table 5: US Version Belt Speeds for Variable Speed 90° Stainless
Gearmotors
Part Number Belt Speed RPM 3 Phase in-lbs N-m
Ft/min M/min HP Kw Volts FLA
74M080HS423EN 2 to 22 0.6 to 6.7 22 0.5 0.37 230/460 1.6/0.8 356 40.2
74M060HS423EN 3 to 29 0.9 to 8.8 29 0.5 0.37 230/460 1.6/0.8 442 49.9
74M040HS423EN 5 to 44 1.3 to13.4 44 0.5 0.37 230/460 1.6/0.8 486 54.9
74M030HS423EN 6 to 58 2 to 17.7 58 1 0.74 208-230/460 3.5-3.2/1.6 487 55.0
74M020HS423EN 9 to 87 2.6 to 26.5 87 1 0.74 208-230/460 3.5-3.2/1.6 487 55.0
74M015HS423EN 12 to 117 3.6 to 35.7 117 1 0.74 208-230/460 3.5-3.2/1.6 470 53.1
74M010HS423EN 18 to 175 5.3 to 53.3 175 1.5 1.11 208-230/460 4.6-4.2/2.1 442 49.9
74M007HS423EN 23 to 233 7.1 to 71.0 233 1.5 1.11 208-230/460 4.6-4.2/2.1 360 40.7
Part Number
Belt Speed
(Ft/min)
Belt Speed
(M/min) RPM FLA N-m
Min Max Min Max Min Max Kw Volts Phase at 230V at 400V
73U060HS423EN 6 37 3.5 7.0 6 37 0.37 230/400 3 1.91 1.1 81
73U030HS423EN 11 74 7.0 14.0 11 74 0.75 230/400 3 3.65 2.1 102
73U025HS423EN 13 88 8.4 16.8 13 88 0.75 230/400 3 3.65 2.1 94
73U015HS423EN 22 149 14.2 28.3 22 149 1.12 230/400 3 4.89 2.81 89
73U010HS423EN 34 224 21.3 42.7 34 224 1.12 230/400 3 4.89 2.81 64
73U007HS423EN 45 298 28.3 56.7 45 298 1.49 230/400 3 6.17 3.55 67
Part Number Belt Speed RPM 3 Phase in-lbs N-m
Ft/min M/min HP Kw Volts FLA
74M080HZS423FN 22 6.7 22 0.5 0.37 230/460 1.6/0.8 356 40.2
74M060HZS423FN 29 8.8 29 0.5 0.37 230/460 1.6/0.8 442 49.9
74M040HZS423FN 44 13.4 44 0.5 0.37 230/460 1.6/0.8 486 54.9
74M030HZS423FN 58 17.7 58 1 0.74 208-230/460 3.2-3/1.5 487 55.0
74M020HZS423FN 87 26.5 87 1 0.74 208-230/460 3.2-3/1.5 407 46.0
74M015HZS423FN 117 35.7 117 1 0.74 208-230/460 3.2-3/1.5 470 53.1
74M010HZS423FN 175 53.3 175 1.5 1.11 208-230/460 5.8-5.4/2.7 442 49.9
74M007HZS423FN 233 71.0 233 1.5 1.11 208-230/460 5.8-5.4/2.7 360 40.7
Part Number Belt Speed RPM 3 Phase in-lbs N-m
Ft/min M/min HP Kw Volts FLA
74M080HZS423EN 2 to 22 0.6 to 6.7 22 0.5 0.37 230/460 1.6/0.8 356 40.2
74M060HZS423EN 3 to 29 0.9 to 8.8 29 0.5 0.37 230/460 1.6/0.8 442 49.9
74M040HZS423EN 5 to 44 1.3 to13.4 44 0.5 0.37 230/460 1.6/0.8 486 54.9
74M030HZS423EN 6 to 58 2 to 17.7 58 1 0.74 208-230/460 3.2-3/1.5 487 55.0
74M020HZS423EN 9 to 87 2.6 to 26.5 87 1 0.74 208-230/460 3.2-3/1.5 487 55.0
74M015HZS423EN 12 to 117 3.6 to 35.7 117 1 0.74 208-230/460 3.2-3/1.5 470 53.1
74M010HZS423EN 18 to 175 5.3 to 53.3 175 1.5 1.11 208-230/460 5.3-5.4/2.7 442 49.9
74M007HZS423EN 23 to 233 7.1 to 71.0 233 1.5 1.11 208-230/460 5.3-5.4/2.7 360 40.7
NOTE
For belt speed other than those listed, contact
factory for details.

851-679 Rev. C 7 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Installation
US Version Side Drive Package
Required Tools
•5/16" wrench
• 4 mm wrench
• 13 mm wrench
• 14 mm wrench
• Large flat head screwdriver
• Torque wrench
Figure 2
Figure 2
Typical Side Drive Package Components (Figure 3).
Figure 3
Figure 3
1. On each side of conveyor, remove upper front headplate
mounting screw and install spacer (Figure 4, item 1)
with longer screw (Figure 4, item 2).
Figure 4
Figure 4
A
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
A
WARNING
PUNCTURE HAZARD!
Handle drive shaft keyway with care. It may
be sharp and could puncture the skin,
causing serious injury.
NOTE
Gearmotor may be operated in positions 1 or
3 (Figure 2).
13
1Cover
2 Hex Head Cap Screw 5/16-18 x .75" (x2)
3 Hex Head Cap Screw 5/16-18 x .50" (x2)
4 Cover Bracket
5 Support Arm
6 Mounting Bracket
7 Hex Head Cap Screw M8-1.25 x 40 mm
8 Gearmotor Assembly
2
6
13
8
4
7
5
1
2

Dorner Mfg. Corp. 8 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Installation
2. Install mounting bracket (Figure 5, item 1) onto gear
reducer (Figure 5, item 2) with screws.
Figure 5
Figure 5
3. Install key onto conveyor shaft (Figure 5, item 3), and
slide gear reducer assembly onto shaft.
4. Slide mounting bracket (Figure 6, item 1) onto spacer
(Figure 6, item 2) on conveyor, and tighten set screws
on both bearings (Figure 6, item 3) with a hex key
wrench (Figure 6, item 4).
Figure 6
Figure 6
5. Install gear reducer output shaft cover
(Figure 7, item 1).
Figure 7
Figure 7
6. Install cover bracket (Figure 7, item 2) onto gear
reducer with screws (Figure 7, item 3).
7. Install shaft key (Figure 8, item 1) onto motor shaft
(Figure 8, item 2), and install motor (Figure 8, item 3)
onto gear reducer (Figure 8, item 4).
Figure 8
Figure 8
8. Secure motor (Figure 9, item 1) to gear reducer
(Figure 9, item 2), with four bolts (Figure 9, item 3).
Figure 9
Figure 9
9. Tighten four bolts (Figure 9, item 3) to 65 in−lbs (7.3
N−m).
1
3
2
2
4
1
3
3
1
2
IMPORTANT
Be extremely careful when coupling motor to
gear reducer. Avoid misalignment and forcing
the connection causing possible permanent
gear reducer seal damage.
34
1
2
12
3

851-679 Rev. C 9 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Installation
CE Version Side Drive Package
Required Tools
•3/16" hex wrench
• 8 mm hex wrench
• 13 mm wrench
• Large flat head screwdriver
Figure 10
Figure 10
Typical Side Drive Package Components (Figure 11).
Figure 11
Figure 11
1. On side of conveyor motor is being installed, remove
upper front head plate mounting screw
(Figure 12, item 1).
Figure 12
Figure 12
A
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
A
WARNING
PUNCTURE HAZARD!
Handle drive shaft keyway with care. It may
be sharp and could puncture the skin,
causing serious injury.
NOTE
Gearmotor may be operated in positions 1 or
3 (Figure 10).
13
1 Hex Head Cap Screw, M8-1.25 x 20 mm (x2)
2 Hex Head Cap Screw, M8-1.25 x 40 mm
3 Collar Clamp
4 Support Arm
5 Mounting Bracket
6 Hex Head Cap Screw, M10-0.50 x 40 mm
7 Gearmotor Assembly
5
6
3
7
2
4
1
1

Dorner Mfg. Corp. 10 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Installation
2. Install support arm (Figure 13, item 1) with longer
screw (Figure 13, item 2)
Figure 13
Figure 13
3. Install mounting bracket (Figure 14, item 1) onto
output shaft and support arm (Figure 14, item 2).
Figure 14
Figure 14
4. Install one half of collar clamp (Figure 14, item 3) up to
line (Figure 14, item 4) conveyor shaft.
5. Install second half of collar clamp (Figure 15, item 1)
and secure with two hex socket head screws
(Figure 15, item 2).
Figure 15
Figure 15
6. Install key onto conveyor shaft (Figure 16, item 1), and
slide gearmotor assembly (Figure 16, item 2) onto shaft
and mounting bracket (Figure 16, item 3).
Figure 16
Figure 16
7. Install four screws (Figure 17, item 1) to gearmotor
assembly and mounting bracket (Figure 17, item 2).
Figure 17
Figure 17
8. Install gear reducer end cap (Figure 18, item 1) with
socket head screw (Figure 18, item 2).
Figure 18
Figure 18
1
2
1
3
2
4
1
2
2
1
2
3
12
1
1
2

851-679 Rev. C 11 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Preventive Maintenance and Adjustment
Required Tools
•3/16" hex wrench
• 8 mm hex wrench
•5/16" wrench
• 4 mm wrench
• 13 mm wrench
• 14 mm wrench
• Large flat head screwdriver
• Torque wrench
Check List
• Keep service parts on hand. Refer to “Service Parts” on
page 15 for recommendations.
• Replace any worn or damaged parts.
US Version Gear Reducer
Replacement
1. Remove four bolts (Figure 19, item 1) securing motor
(Figure 19, item 2) to gear reducer (Figure 19, item 3).
Figure 19
Figure 19
2. Slide motor (Figure 20, item 1) off of gear reducer
(Figure 20, item 2),and remove shaft key
(Figure 20, item 3) from motor shaft
(Figure 20, item 4).
Figure 20
Figure 20
A
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
A
WARNING
BURN HAZARD!
DO NOT TOUCH the motor while operating, or
shortly after being turned off. Motors may be
HOT and can cause serious burn injuries.
A
WARNING
CRUSH HAZARD!
• SUPPORT MOTOR PRIOR TO LOOSENING
THE BOLTS
• Loosening motor bolts may cause it to drop
down, causing serious injury.
NOTE
Be sure to retain the motor output shaft key.
23
1
12
3
4

Dorner Mfg. Corp. 12 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Preventive Maintenance and Adjustment
3. Remove two screws (Figure 21, item 1) and gear
reducer output shaft cover and bracket
(Figure 21, item 2).
Figure 21
Figure 21
4. Use a hex key wrench (Figure 22, item 1) to remove set
screws on both bearings (Figure 22, item 2).Slide gear
reducer and mounting bracket (Figure 22, item 3) from
spacer (Figure 22, item 4) on conveyor.
Figure 22
Figure 22
5. Remove gear reducer assembly from conveyor shaft
(Figure 23, item 1), making sure to not lose key on
conveyor shaft.
Figure 23
Figure 23
6. Remove screws and mounting bracket
(Figure 23, item 2) from gear reducer
(Figure 23, item 3).
7. To install components, complete steps 3 through 9 of
“US Version Side Drive Package” on page 7“.
US Version Motor Replacement
1
2
4
1
3
2
A
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
A
WARNING
BURN HAZARD!
DO NOT TOUCH the motor while operating, or
shortly after being turned off. Motors may be
HOT and can cause serious burn injuries.
2
1
3

851-679 Rev. C 13 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Preventive Maintenance and Adjustment
1. Loosen terminal box screws (Figure 24, item 1) and
remove cover (Figure 24, item 2).
Figure 24
Figure 24
2. Refer to the wiring diagram (Figure 25, item 1) on the
inside of the junction box cover.
Figure 25
Figure 25
3. Loosen the wire nuts and disconnect the wires.
4. Loosen the cord grip and remove the cord.
5. Remove four bolts (Figure 26, item 1) securing motor
(Figure 26, item 2) to gear reducer (Figure 26, item 3).
Figure 26
Figure 26
6. Slide motor (Figure 27, item 1) off of gear reducer
(Figure 27, item 2),and remove shaft key
(Figure 27, item 3) from motor shaft
(Figure 27, item 4).
Figure 27
Figure 27
7. With key (Figure 27, item 3) in keyway on motor shaft
(Figure 27, item 4), slide new motor
(Figure 27, item 1) and gear reducer
(Figure 27, item 2) together.
A
DANGER
ELECTRICAL HAZARD!
LOCK OUT POWER BEFORE WIRING.
Exposure to high voltage current can cause
death or serious injury.
1
2
1
2
1
A
WARNING
CRUSH HAZARD!
• SUPPORT MOTOR PRIOR TO LOOSENING
THE BOLTS
• Loosening motor bolts may cause it to drop
down, causing serious injury.
NOTE
Be sure to retain the motor output shaft key.
23
1
12
3
4

Dorner Mfg. Corp. 14 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Preventive Maintenance and Adjustment
8. Secure motor (Figure 28, item 1) to gear reducer
(Figure 28, item 2), with four bolts
(Figure 28, item 3).
Figure 28
Figure 28
9. Tighten four bolts (Figure 28, item 3) to 65 in−lbs (7.3
N−m).
10. Rewire the motor and attach the box cover.
CE Version Gearmotor Replacement
1. Remove socket head screw (Figure 29, item 1) and gear
reducer end cap (Figure 29, item 2).
Figure 29
Figure 29
2. Remove four screws (Figure 30, item 1) attaching
gearmotor assembly (Figure 30, item 2) from mounting
bracket (Figure 30, item 3).
Figure 30
Figure 30
3. Remove gearmotor assembly from shaft and bracket.
4. Retain key on gearmotor shaft.
5. Replace gearmotor assembly in reverse order of
removal. Tighten four screws to secure.
6. Install end cap with socket head screw.
A
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
A
WARNING
BURN HAZARD!
DO NOT TOUCH the motor while operating, or
shortly after being turned off. Motors may be
HOT and can cause serious burn injuries.
12
3
A
WARNING
CRUSH HAZARD!
• SUPPORT MOTOR PRIOR TO LOOSENING
THE BOLTS
• Loosening motor bolts may cause it to drop
down, causing serious injury.
2
1
13
12

851-679 Rev. C 15 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Service Parts
US Version Side Mount Drive Package for 90° Gearmotors
NOTE
For replacement parts other than those shown in this section, contact an authorized Dorner Service Center
or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo . Dorner
recommends keeping these parts on hand.
1
2
3
4
5
6
7
Item Part Number Description
1 807-1454 Cover
2 906-061SS Hex Head Cap Screw 5/16-18 x .75"
3 906-067SS Hex Head Cap Screw 5/16-18 x .50"
4 500492 Cover Bracket
5 532146 Support Arm
6 532148 Mounting Bracket
7 960840MSS Hex Head Cap Screw M8-1.25 x 40 mm

Dorner Mfg. Corp. 16 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Service Parts
CE Version Side Mount Drive Package for 90° Gearmotors
5
1
4
2
3
6
Item Part Number Description
1 807-1817 Collar Clamp
2 532146 Support Arm
3 532290 Mounting Bracket
4 921040MSS Socket Head Screw, M10-.50 x 40 mm
5 960820MSS Hex Head Cap Screw, M8-1.25 x 20 mm
6 960840MSS Hex Head Cap Screw, M8-1.25 x 40 mm

851-679 Rev. C 17 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Service Parts
US Version Gearmotor Assembly
1
2
3
Item Part Number Description
1 62MZ411 Painted Motor, 0.50 Hp (0.37Kw) 115
Volts, 60Hz, 1 Phase
62MZ423 Painted Motor, 0.50 Hp (0.37Kw) 208-
230/460 Volts, 6 to 60Hz, 3 Phase
74MHS423-10 Painted Motor, 1.00 Hp (0.74Kw) 208-
230/460 Volts, 6 to 60Hz, 3 Phase
74MHS423-15 Painted Motor, 1.50 Hp (1.11Kw) 208-
230/460 Volts, 6 to 60Hz, 3 Phase
62MZS423 Stainless Steel Motor, 0.50 Hp
(0.37Kw) 208-230/460 Volts, 6 to 60Hz,
3 Phase
74MZS423-10 Stainless Steel Motor, 1.00 Hp
(0.74Kw) 208-230/460 Volts, 6 to 60Hz,
3 Phase
74MZS423-15 Stainless Steel Motor, 1.50 Hp
(1.11Kw) 208-230/460 Volts, 6 to 60Hz,
3 Phase
Item Part Number Description
2 74M005HS Painted Gear Reducer, 5:1, 56C
74M007HS Painted Gear Reducer, 7:1, 56C
74M010HS Painted Gear Reducer, 10:1, 56C
74M015HS Painted Gear Reducer, 15:1, 56C
74M020HS Painted Gear Reducer, 20:1, 56C
74M030HS Painted Gear Reducer, 30:1, 56C
74M040HS Painted Gear Reducer, 40:1, 56C
74M060HS Painted Gear Reducer, 60:1, 56C
74M080HS Painted Gear Reducer, 80:1, 56C
74M005HZ Stainless Steel Gear Reducer, 5:1, 56C
74M007HZ Stainless Steel Gear Reducer, 7:1, 56C
74M010HZ Stainless Steel Gear Reducer, 10:1, 56C
74M015HZ Stainless Steel Gear Reducer, 15:1, 56C
74M020HZ Stainless Steel Gear Reducer, 20:1, 56C
74M030HZ Stainless Steel Gear Reducer, 30:1, 56C
74M040HZ Stainless Steel Gear Reducer, 40:1, 56C
74M060HZ Stainless Steel Gear Reducer, 60:1, 56C
74M080HZ Stainless Steel Gear Reducer, 80:1, 56C
3 917-104 Stainless Steel Socket Head Cap Screw
10-32 x .25 for Painted Gearmotor
916-126 Stainless Steel Button Head Cap Screw
1/4-20 x .31 for Stainless Steel
Gearmotor

Dorner Mfg. Corp. 18 851-679 Rev. C
7350 Series Side Mount 90° Drive Package
Service Parts
CE Version Gearmotor Assembly
1
Item Part Number Description
1 73U060HS423FN Gearmotor, Fixed Speed, 0.37 Kw
230/400V 3 Phase, 50 Hz, 23 RPM
73U030HS423FN Gearmotor, Fixed Speed, 0.75 Kw
230/400V 3 Phase, 50 Hz, 46 RPM
73U025HS423FN Gearmotor, Fixed Speed, 0.75 Kw
230/400V 3 Phase, 50 Hz, 55 RPM
73U015HS423FN Gearmotor, Fixed Speed, 1.12 Kw
230/400V 3 Phase, 50 Hz, 93 RPM
73U010HS423FN Gearmotor, Fixed Speed,
1.12 Kw 230/400V 3 Phase,
50 Hz, 140 RPM
73U007HS423FN Gearmotor, Fixed Speed,
1.49 Kw 230/400V 3 Phase,
50 Hz, 186 RPM
73U005HS423FN Gearmotor, Fixed Speed,
1.49 Kw 230/400V 3 Phase,
50 Hz, 279 RPM
73U060HS423EN Gearmotor, Variable Speed,
0.37 Kw 230/400V 3 Phase,
12-80 Hz, 37 RPM
73U030HS423EN Gearmotor, Variable Speed,
0.75 Kw 230/400V 3 Phase,
12-80 Hz, 74 RPM
73U025HS423EN Gearmotor, Variable Speed,
0.75 Kw 230/400V 3 Phase,
12-80 Hz, 88 RPM
73U015HS423EN Gearmotor, Variable Speed,
1.12 Kw 230/400V 3 Phase,
12-80 Hz, 149 RPM
73U010HS423EN Gearmotor, Variable Speed,
1.12 Kw 230/400V 3 Phase,
12-80 Hz, 224 RPM
73U007HS423EN Gearmotor, Variable Speed,
1.49 Kw 230/400V 3 Phase,
12-80 Hz, 298 RPM

851-679 Rev. C 19 Dorner Mfg. Corp.
7350 Series Side Mount 90° Drive Package
Notes

Dorner Mfg. Corp. reserves the right to change
or discontinue products without notice. All
products and services are covered in
accordance with our standard warranty. All
rights reserved. © Dorner Mfg. Corp. 2009
DORNER MFG. CORP.
975 Cottonwood Ave., PO Box 20
Hartland, WI 53029-0020 USA
TEL [phone] (USA)
FAX [phone] (USA)
Internet: www.dorner.com
Outside the USA:
TEL [phone]
FAX [phone]
851-679 Rev. C Printed in U.S.A.
Return Policy
Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without
authorization will not be credited nor returned to the original sender. When calling for authorization, please have the
following information ready for the Dorner factory representative or your local distributor:
1. Name and address of customer.
2. Dorner part number(s) of item(s) being returned.
3. Reason for return.
4. Customer's original order number used when ordering the item(s).
5. Dorner or distributor invoice number (if available, part serial number).
A representative will discuss action to be taken on the returned items and provide a Returned Goods Authorization (RMA)
number for reference. RMA will automatically close 30 days after being issued. To get credit, items must be new and
undamaged. There will be a return charge on all items returned for credit, where Dorner was not at fault. It is the
customer’s responsibility to prevent damage during return shipping. Damaged or modified items will not be accepted. The
customer is responsible for return freight.
Conveyors and conveyor accessories
Standard catalog conveyors 30%
MPB, 7200, 7300 Series, cleated and specialty belt 50%
AquaGard & AquaPruf Series conveyors non-returnable items
Engineered special products case by case
Drives and accessories 30%
Sanitary stand supports non-returnable items
Parts
Standard stock parts 30%
Plastic chain, cleated and specialty belts non-returnable items
Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning,
disassembly, disposal and reissuing of components to inventory. If a replacement is needed prior to evaluation of returned
item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete.
Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer
Service Teams will gladly help with your questions on Dorner products.
For a copy of Dorner's Warranty, contact factory, distributor, service center or visit our website at www.dorner.com.
For replacement parts, contact an authorized Dorner Service Center or the factory.