DR. Heater DR-PS11024 User manual

1
Salaman
der Heater
OWNER’S MANUAL
Model：DR-PS11024
10KW 240V 60Hz 1P
DR-PS11524
15KW 240V 60Hz 1P
DR-PS31520
15KW 208V 60Hz 3P
IMPORTANT INSTRUCTIONS
R AD & SAV
der Heater
10KW 240V 60Hz 1P
15KW 240V 60Hz 1P
15KW 208V 60Hz 3P
IMPORTANT INSTRUCTIONS

2
TABLE OF CONTENTS
Important Instruct ons………………………………………...3-4
Parts of the Heater ……………………….……………………5
Install ng Instruct ons……………………….…………..…….6-9
Spec f cat ons and W r ng D agram………………………. ..10-14
Operat ng Instruct ons……………………….………....……..15
Ma ntenance and Clean ng……………………………………16
Warranty Informat on ………………………………………….17
ARRANTY INFORMATION

3
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER
NOTE: There may be a trace of smoke or odor when un t s f rst
operated. Don’t be alarmed. Th s nd cates that a drop of o l fell on
the heat ng co l dur ng the manufactur ng process. It w ll qu ckly
evaporate and should not re-occur.
Make sure that the room n wh ch the appl ance s located s well
vent lated dur ng th s operat on. It s normal for the appl ance to
em t small crack ng sounds when you turn t on for the f rst t me. Do
not be alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE,
ELECTRICAL SHOCK, AND INJURY TO PERSONS OR PROPERTY,
INCLUDING THE FOLLOWING:
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Keep combustible materials such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away from the sides and rear.
3) xtreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has been
dropped, or damaged in any manner. Disconnect power at service panel
and have heater inspected by a licensed electrician before reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main
disconnect panel.
8) Do not install closer than 4 feet (1.2 m) from any adjacent vertical
surfaces. Keep at least 1 foot (0.9 m) away from the back wall,
regardless of whether the wall mounting bracket is used.
9) When heater is installed on the cart, make sure the cart is positioned
on a level surface. Keep at least 4 feet (1.2 m) from any adjacent vertical
surface or wall. Keep at least 1 foot (0.9 m) from the back wall.

4
10) Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or damage
the heater.
11) To prevent a possible fire, do not block air intakes or exhaust in any
manner.
12) A heater has hot and arcing or sparking parts inside. To reduce the
risk of fire, do not use it in areas where gasoline, paint, or flammable
vapors and liquids are used or stored.
13) Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
14) This product must be installed by a certified/licensed electrician, in
accordance with local codes.
15) Do NOT use an extension cord.
16) This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
CAUTION – HIGH TEMPERATURE, RISK OF FIRE
Keep electr cal cords, drapery, furn sh ngs, and other combust bles
at least 3 feet (0.9 m) from the front of the heater and away from the
s des and rear.
PET OWNER’S WARNING:
The health of some small pets nclud ng b rds are extremely sens t ve
to the fumes produced dur ng the f rst-t me use of many appl ances.
These fumes are not harmful to humans but we recommend that you
do not use your heater around b rds and other small pets dur ng ts
n t al use unt l the ant -corros on coat ngs burn off.
SAVE THESE INSTRUCTIONS

5
A. Handle
B. Heater Housing
C. Tilt adjustable knob
D. Wheel
. Front Grill
F. ON/OFF Switch
G. Temperature Setting Knob
PARTS OF THE HEATER
A
D
G
F
B
C

6
WARNING: All wiring must be installed by a certified/licensed
electrician.
The heater must be grounded in accordance with all national and local
building codes.
All w r ng procedures and connect ons shall be n accordance w th
the relevant nat onal and local codes.
Before nstallat on:
Disconnect the main supply connection.
DR-PS11024, the heater must be connected to an individual branch
circuit protected by a 55 Amp circuit breaker.
Supply cables must be equipped with a dual pole circuit breaker rated at
least 240V 55A/pole as the main cutoff switch of power to the heater.
DR-PS31520, the heater must be connected to an individual branch
circuit protected by a 55 Amp circuit breaker.
Supply cables must be equipped with a dual pole circuit breaker rated at
least 208V 55A/pole as the main cutoff switch of power to the heater.
DR-PS11524, the heater must be connected to an individual branch
circuit protected by an 80 Amp circuit breaker.
Supply cables must be equipped with a dual pole circuit breaker rated at
least 240V 80A/pole as the main cutoff switch of power to the heater.
CAUTION : HIGH T MP RATUR , RISK OF FIR
Keep electrical cords, drapery, furnishings, and other combustibles at
least 3 feet (0.9 m) from the front of the heater and away from the sides
and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline or
other flammable vapors and/or liquids in the vicinity of the heater.
INSTALLING INSTRUCTIONS

7
INSTALLATION INSTRUCTIONS:
1. Open the package; take out the heater and the foot stand parts.
The parts list as below:
No. Item Spec Quantity
No. Item Spec Quantity
1 Axle 1 9 Washer
Φ8 8
2 Handle 1 10 Screw M8X80 4
3 Foot Stand 2 11 Screw M6X55 2
4 Wheel 2 12 Washer
Φ6 2
5 Axle Sleeve 2 13 Nut M6X20 2
6 Nut M12 2 14 Knob 2
7 Washer
Φ12 4 15 Washer Φ10 2
8 Nut M8 4 16 Rubber Pad
Φ50X10 2

8
2. Use axle (item 1), axle sleeve (item 5), and washer (item 7) to
assemble the foot stand and the wheels as shown below:
3. Tighten the nuts (item 6) to the wheels as shown below:
4. Use the screw (item 10), washer (item 9), and nut (item 8) to assemble
the handle to the foot stand as shown below. Tighten the nuts.

9
5. Use the rubber pad (item 16), washer (item 15), and the knobs (item
14) to assemble the heater to the foot stand. Tighten the knobs as shown
below:
6. Insert the screws (item 11) and the nuts (item 13) to the location hole
of the foot stand. Tighten the nuts.
7. Run the electrical power supply cable in flexible conduit and connect
to the wiring compartment.
8. Make the connections properly with connectors which are suitable for
the conductor size, including ground wires. After making the
connections, arrange the pigtail leads of unit and power supply wires
in the wiring compartment.

10
Salamander Heater w th cart
Model: DR-PS11024
Volt: 240V, 1P
Watts: 10KW
Frequency: 60 Hz
Wiring diagram:
SPECIFICATIONS
DR
-
PS11024

11
Model: DR-PS11524
Volt: 240V, 1P
Watts: 15KW
Frequency: 60 Hz
Wiring diagram:
DR
-
PS11
5
24

12
Model: DR-PS31520
Volt: 208V, 3P
Watts: 15KW
Frequency: 60 Hz
Wiring diagram:
DR
-
PS
31520

13
For 1 Phase Model: PS-10241, PS-15241
1. Open the wiring cover:
2. Connect the black live wire to L1, white
live wire to L2 of the terminal
block.
3. Re-install the wiring cover to the heater.
WIRING
INSTRUCTIONS
L2 White Wire
L1 Black Wire
live wire to L2 of the terminal
INSTRUCTIONS

14
For 3 Phase Model: DR-PS31520
1. Open the wiring cover:
2. Connect the red live
wire to L1, black live wire to L2, and the white live
wire to L3 of the connector.
3. Re-install the wiring cover to the heater.
Ground Wire
L2: Black
Live Wire
L1: Red
Live Wire
L3: White
Live Wire
wire to L1, black live wire to L2, and the white live

15
WARNING - The heater must be properly nstalled before t s
used.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC
FLASH :
 Apply appropr ate personal protect ve equ pment (PPE) and
follow safe electr cal work pract ces. See NFPA 70E.
 A c rcu t breaker must be nstalled and serv ced only by
qual f ed electr cal personnel.
 Always use a properly rated voltage sens ng dev ce to conf rm
power s off.
 Switch the ON/OFF switch to ON position to turn on the heater.
Then turn the thermostat to the farthest clockwise position. The
power indicator light will turn on, the fan will engage, and the unit will
begin heating the room. After the room reaches a comfortable
temperature, turn the thermostat counterclockwise until the heater
shuts off. The heater will automatically cycle around this preset
temperature. To increase the temperature, turn the thermostat knob
clockwise. To lower the temperature, turn the thermostat
counterclockwise.
 Select a thermostat setting.
Ambient temperature is regulated by adjusting the thermostat to a
desired position. Allow the unit to operate and warm up the room. When
the desired temperature is reached, turn the control knob
counterclockwise until the heater turns off. This is your ideal setting. The
heater will start automatically when the room temperature drops below
this set point, and will turn off when the set point is reached.
 To turn off the heater, switch the ON/OFF switch to OFF
position.
OPERATING
INSTRUCTIONS

16
No user maintenance on this heater should be undertaken except regular
cleaning as described below. All other servicing or maintenance should
be performed by qualified service personnel.
Before any cleaning, make sure that:
1. Power supply is disconnected at the source.
2. Wait 60 minutes to ensure the heating element has cooled down.
Your heater is now ready for cleaning.
Regular Cleaning:
1. Do not spray cleaning liquids or other chemicals on the unit.
2. Interior dust can often be removed by using a vacuum cleaner with a
crevice tool attachment.
3. To clean enclosure, use a clean, soft, and lightly damp cloth to gently
wipe off the dirt from the surface of the unit. Be sure not to wet the
heating element or the switches. Allow the unit to dry completely
before use.
CAUTION: DO NOT ALLOW WAT R TO RUN INTO TH INT RIOR OF
TH H AT R AS THIS COULD CR AT A FIR OR L CTRIC
SHOCK HAZARD, DAMAGING TH UNIT.
MAINTENCE
AND
CLEANING

17
This product comes with a ON -Y AR LIMIT D
COMPON NT
WARRANTY. If your unit does not appear to be working properly, please
contact our service center by calling 1-800-317-1688.
Dr. Infrared Heater
239 Harbor Way
SOUTH SAN FRANCISCO, CA 94080
T L: 800-317-1688
MAIL:
S RVIC @DRH AT RUSA.COM
Dr Heater USA
@DrHeaterUSA
Dr. Heater USA
Dr. Heater USA
WARRANTY INFORMATION
COMPON NT
WARRANTY. If your unit does not appear to be working properly, please
S RVIC @DRH AT RUSA.COM
WARRANTY INFORMATION