Dr. Trust Air Mattress Bubble User manual

Air Mattress Bubble
INSTRUCTION MANUAL
Dr Trust Air Mattress is designed
specifically to cure Bed Sores in patients with prolong Bed Rest.
occur, if a patient is lying on the bed for a long period of time
exerted on the body. Other Factors like
Temperature
specially designed to refrain patient’s muscle from long
and High quality mat
erial used to make the
durability makes it ideal not only for home use but also for Hospitals.
system with pump offers patients more benefit than linear style pad as it allows more Touch points offering a
superior therapy system.
Principle of Operation
The bed-type medical air cushion
is composed
ballonets. Under the control of the mainframe, every ballonet can touch a
fluctuant ballonet
can expedite blood circulati
Operation Directions
• Place the pump
of air mattress on a flat table.
•
Unfold & lay the air mattress on a foam mattress
•
Connect one end of the air tubes with the air pump and the other end with the air mattress. Connect them
firmly at both the ends.
• Switch on the electric pump of
the air mattress by connecting with
Keep the pressure adjusting Knob at full in the beginning. This will take around 1
•
The pump should be constantly switched on during the usage otherwise the mattress will deflate.
•
After around 10 minutes A type bubbles will inflate
with the adjusting Knob in
such a way that there is a two finger
patient.
•
To repack the mattress when not in use, you need to
•
Keep the electric pump of air mattress on for 23 hours and keep it off for 1 hour.
• Do not smoke near the air mattress
•
Do not use the air mattress near open flame or very nea
•
Keep sharp objects away from the air mattress.
•
Maximum weight bearing capacity is 100 kgs therefore the attendants should not sit on the air mattress as this
will cause the mattress to leak.
Do not stand on the air mattress.
•
Keep the pump of the air mattress away from water/damp surfaces
Clean the mattress with mild detergent if required.
Air Mattress Bubble
INSTRUCTION MANUAL
Brief Introduction
specifically to cure Bed Sores in patients with prolong Bed Rest.
occur, if a patient is lying on the bed for a long period of time
. Main Reason of Bed Sores
is the continuous pressure
Temperature
or Humidity worsen the bed sores.
Dr Trus
specially designed to refrain patient’s muscle from long
-term fixed pressure at same position.
Heavy Duty air Pump
erial used to make the
Mattress makes it a trusted & long-
lasting Medical equipment. Its
durability makes it ideal not only for home use but also for Hospitals.
The Alternating Pressure Relief Bubble pad
system with pump offers patients more benefit than linear style pad as it allows more Touch points offering a
Principle of Operation
is composed
of two parts: mainframe and air cushion
. The air cushion has two separate
ballonets. Under the control of the mainframe, every ballonet can touch a
different part of
body every six minutes. The
can expedite blood circulati
on & also balance the pressure exerted by the body.
Operation Directions
of air mattress on a flat table.
Unfold & lay the air mattress on a foam mattress
/bed in a way that the conn
ections are on the foot side.
Connect one end of the air tubes with the air pump and the other end with the air mattress. Connect them
the air mattress by connecting with
Power.
The air mattress will start inflating.
Keep the pressure adjusting Knob at full in the beginning. This will take around 1
0-15
minutes to inflate.
The pump should be constantly switched on during the usage otherwise the mattress will deflate.
After around 10 minutes A type bubbles will inflate
& B type will remain deflated
. Adjust pressure ideally
such a way that there is a two finger
gap between the deflated air bubbles and the
To repack the mattress when not in use, you need to
deflate the mattress
by pressing it from other side.
Precaution
Keep the electric pump of air mattress on for 23 hours and keep it off for 1 hour.
Do not use the air mattress near open flame or very nea
r to a heater.
Keep sharp objects away from the air mattress.
Maximum weight bearing capacity is 100 kgs therefore the attendants should not sit on the air mattress as this
Do not stand on the air mattress.
Keep the pump of the air mattress away from water/damp surfaces
as humidity will deteriorate the product
Clean the mattress with mild detergent if required.
specifically to cure Bed Sores in patients with prolong Bed Rest.
Bed sores may
is the continuous pressure
Dr Trus
t Air Mattress is
Heavy Duty air Pump
lasting Medical equipment. Its
The Alternating Pressure Relief Bubble pad
system with pump offers patients more benefit than linear style pad as it allows more Touch points offering a
. The air cushion has two separate
body every six minutes. The
ections are on the foot side.
Connect one end of the air tubes with the air pump and the other end with the air mattress. Connect them
The air mattress will start inflating.
minutes to inflate.
The pump should be constantly switched on during the usage otherwise the mattress will deflate.
. Adjust pressure ideally
gap between the deflated air bubbles and the
by pressing it from other side.
Maximum weight bearing capacity is 100 kgs therefore the attendants should not sit on the air mattress as this
as humidity will deteriorate the product
.

•
Make sure the Conduit is not twisted or bent.
•
Store the Air mattress in a Breezy room wherein relative temperature is not more
sunlight or corrosive gas.
MODE OF AIRFILL
PHASEl/A MODE
PHASE 2/B MODE
PHASE 3/C MODE
VOITAGE
FREQUENCY
CONSUEMED POWER
NOISE
WORKING WAY
Thank you for choosing our product.
Please read the Operation Manu
al Carefully before Using.
Imported & Marketed By
Nectar Lifesciences Limited
Works : Unit-
II, ViII. Saidpura, Teh.Derabassi,
Distt. Mohali, Punjab, Pin-140507
Customer Care : +91-172-
3078158, Fax : +91
E-
mail : [e-mail], Website : www.necli
IS0 9001:2008 & IS0 13485:2003 certified company
Made in PRC
Make sure the Conduit is not twisted or bent.
Store the Air mattress in a Breezy room wherein relative temperature is not more
than 80% and without direct
MODE OF AIRFILL
PHASEl/A MODE
PHASE 2/B MODE
PHASE 3/C MODE
Specifications
AC ~ 220V±10%
50Hz ± 1Hz
≤ 15W
＜ 50dB （ A ）
CONTINUE
al Carefully before Using.
II, ViII. Saidpura, Teh.Derabassi,
3078158, Fax : +91
-172-3078155
mail : [e-mail], Website : www.necli
fe.com
IS0 9001:2008 & IS0 13485:2003 certified company
than 80% and without direct