Draytek Vigor VigorAccess IVD User manual

VigorAccess IVD
Quick Start Guide
Version: 1.2
Date: 2007/09/11

Version: 1.2
Quick Start Guide for VigorAccess
2
Table of Contents
NETWORK TOPOLOGY OVERVIEW ..................................................................................................1
MANAGEMENT FOR IVD ..............................................................................................................2
PORT CONNECTION FOR MANAGEMENT..................................................................................2
CONFIGURATION BY USING TERMINAL EMULATOR SOFTWARE ...........................................2


How to Login with a Terminal Emulator Software.......................................................................... 2


How to Login with Telnet................................................................................................................. 2


How to Login to DSL Module for Managing IVD Slave................................................................... 3


How to Plug and Play Slave Device................................................................................................ 3


How to Check the Connectivity....................................................................................................... 3


How to Check the Version Information........................................................................................... 4


How to Save the Configuration....................................................................................................... 5
CONFIGURATION BY USING TELNET.........................................................................................6


How to Change Master IP Setting................................................................................................... 6


How to Change Slave IP Setting..................................................................................................... 6


How to Configure IP Address for Slave-Standalone DSL module................................................. 6


How to Login with Telnet................................................................................................................. 6


How to Set G5 and G6 as UPLINK Interface................................................................................... 7
REFERENCE – COMMON USE COMMANDS FOR CONFIGURATION........................................8


How to configure Inband IP Address.............................................................................................. 8


How to configure Outband IP Address........................................................................................... 8


How to configure Static Route........................................................................................................ 8


How to configure NTP and Time..................................................................................................... 9


How to configure SNMP.................................................................................................................. 9


How to Upgrade Firmware .............................................................................................................10


How to Save Configuration............................................................................................................10


How to Enable/Disable the Switch Port.........................................................................................10

Version: 1.2
Quick Start Guide for VigorAccess
3


How to Connect to DSL Module.....................................................................................................10


How to Monitor DSL Status............................................................................................................11


How to Enable/Disable a DSL Port.................................................................................................11


How to Read DSL Training Rate.....................................................................................................11


How to Change ADSL Line Profile.................................................................................................11


How to Change ADSL Line Rate ....................................................................................................12


How to Change ADSL to Fast Channel/Rate .................................................................................12


How to Set ADSL Alarm Profile......................................................................................................12


How to Change VPI/VCI for Existing VCC......................................................................................12


How to Change Management IP Address for Existing Ethernet Port...........................................13


How to Create more VC/EOA/Bridge .............................................................................................13


How to Setup SNMP Community/Host/Trap..................................................................................13


How to Create VLAN.......................................................................................................................13


How to Setup Port VLAN ID (PVID)................................................................................................13


How to Filter MAC Address by Port...............................................................................................14


How to Deny MAC Address Globally.............................................................................................14


How to Filter Net BIOS ...................................................................................................................14


How to Enable Spanning Tree Protocol.........................................................................................14


How to Enable IGMP Snooping......................................................................................................15


How to Upgrade Control Plane Code Remotely............................................................................15


How to Upgrade Full Image Remotely...........................................................................................16


Wizard Commands.........................................................................................................................17


How to Reboot................................................................................................................................18


How to Exit......................................................................................................................................18


How to Set VoIP Protocol Setting ..................................................................................................18


How to Set SIP local port Setting...................................................................................................19


How to Set SIP Proxy Server Setting.............................................................................................19


How to Set MGCP Local Port Setting.............................................................................................20


How to Set MGCP Call Agent Setting ............................................................................................20


How to Set MGCP End Point ID Style Setting................................................................................20

Version: 1.2
Quick Start Guide for VigorAccess
4


How to Set MGCP Wildcarded End Point ID Setting.....................................................................21


How to Set Phone Number.............................................................................................................21


How to Set Codec Setting..............................................................................................................22


How to Set Gain Control Setting....................................................................................................22


How to Set DTMF Relay Setting.....................................................................................................23


How to Set Fax Transport Mode Setting........................................................................................23


How to Set Call Forwarding Setting...............................................................................................24


How to Set User Group Setting......................................................................................................24


How to Set Hotline Setting.............................................................................................................25


How to Set Speed Dial Setting.......................................................................................................25


How to Set Advanced Speed Dial Setting......................................................................................26


How to Set Region Code for Tone Setting.....................................................................................27


How to Set User Defined Busy Tone Setting.................................................................................28


How to Set User Defined Ringing Tone Setting.............................................................................28


How to Set User Defined Congestion Tone Setting ......................................................................29


How to Set Caller ID Type Setting..................................................................................................29


How to Set VoIP RTP Port Setting..................................................................................................30


How to Set ToS Setting...................................................................................................................30


How to Set T.38 Starting Port Setting ............................................................................................30


How to Set T.38 Redundancy Number Setting ..............................................................................31


How to Set Dialing Timeout Setting...............................................................................................31


How to Set Metering.......................................................................................................................31


How to Set NAT Traversal Setting..................................................................................................32


How to Show VoIP Connection Status...........................................................................................33


How to Show SIP Syslog Message................................................................................................33


How to Set Incoming Call Barring Setting.....................................................................................33


How to Set Allow List of Incoming Calls Setting...........................................................................34


How to Set Deny List of Incoming Calls........................................................................................35


How to Activate VoIP configuration...............................................................................................35


How to backup and restore VoIP configuration ............................................................................35

Version: 1.2
Quick Start Guide for VigorAccess
1
I
IV VD D Q Qu ui ic ck k S St ta ar rt t G Gu ui id de e
This quick start guide will provide basic configuration for accessing Internet with VigorAccess IVD.

N
Ne et tw wo or rk k T To op po ol lo og gy y O Ov ve er rv vi ie ew w
Above diagram shows the basic network topology (example) among master device, slave device, MDF, CPE
(ATU-R) router, user’s computer, and phone. One thing is important – always set the VPI/VCI value for the
CPE the same as the ones configured in master and slave IVD device. The default setting for VPI/VCI of IVD
is 8/35. By the way, the values for these devices can be changed (yet must match with CPE) if necessary.
Please finish all the connections according to the real situation of the environment for the devices.
Note: A master device connects to Internet through UP-G connector. Yet, a slave device also can work
alone without connecting the master device. For a standalone slave device, please use UP port to access
Internet with Ethernet cable.

Version: 1.2
Quick Start Guide for VigorAccess IVD
2

M
Ma an na ag ge em me en nt t f fo or r I IV VD D
If users want to configure or monitor the devices, there are some methods provided here. The MGN port on the
master device allows you to make control remotely; yet the Console port on the master/slave device only
allows you to make control locally.
Note: If you are not used to configure the settings with terminal emulator software or Telnet commands,
you can use EMS (SNMP-based) software to manage these devices. For the detailed information, please
contact your dealer.
IP DSLAM can be managed via MGN, Console, even Uplink Ports. It depends on your necessity.

P
Po or rt t C Co on nn ne ec ct ti io on n f fo or r M Ma an na ag ge em me en nt t
No matter what tool you would like to use for managing master and/or slave device, the first thing you have to
do is making correct port connection.
For Master Device For Slave Device
Connect to a PC through
CONSOLE
port. It is
useful for controlling the
device locally.
Connect to a PC through
MGN port. It is useful
for controlling the
master device locally or
remotely.
Connect to a PC through
CONSOLE port. It is
useful for controlling
the device locally.
Connect to a PC through
MGN port. It is useful
for controlling the slave
device locally or
remotely.

C
Co on nf fi ig gu ur ra at ti io on n b by y U Us si in ng g T Te er rm mi in na al l E Em mu ul la at to or r S So of ft tw wa ar re e
How to Login with a Terminal Emulator Software
For Master /Slave Device
1. The default setting is “baud rate 9600, no parity, and 8 bit with 1 stop bit (N,8,1)”.
2. Use any terminal emulator software for executing commands.
Username – admin
Password – 1234
(type ‘exit’to return)
How to Login with Telnet
For IVD Device
1. Make sure the device IP has been configured well. The default IP setting is 172.16.1.2
2. Make sure the connection of MGN port (for outband) or UPLINK port (for inband) is well done.
3. Open Telnet command screen.
4. Username/Password - admin/1234 (type ‘exit’to return)

Version: 1.2
Quick Start Guide for VigorAccess
3
How to Login to DSL Module for Managing IVD Slave
Slave device have DSL/VoIP modules installed. The DSL module plays the core role for aggregating all
ATM traffic coming from DSL ports to the uplink Ethernet interface, and vice versa. Through the master
controller in the master device, administrator can login to the DSL module inside slave device for
managing IVD.
To DSL Module in IVD Slave Device
Only one slave device can be logged in at one time.
- IVD>dsl –c (Connect to dsl device via serial port)
- IVD>dsl –cf (Force the CLI access right to be occupied by a new operator)
How to Plug and Play Slave Device
By default, ports G1 to G6 on master device are disabled. If the slave connects to the master device,
please refer to the picture below to ensure the connection is working well.
Note: Ports G1 to G6 will be enabled with default if the DSL F/W version is above V2.10.2.6.
Please turn on the interface that connected to a
slave device. In the above picture, you have to
turn ON the interface G1, G4 and G6 for they
connect to different slave devices. Use the
command below to turn on the interface.
- Admin>system link -m gn on
(nmeans “1” to “6”)
- Admin>system link
(check the status)
How to Check the Connectivity
To check the connectivity between the Master
and Slave Devices, please do the following: The results
1. Login through terminal emulator software.
2. Type the following command
- Admin>dsl
You will get the following results:
- Admin>dsl
Logic-Name Slave-IP Connection-Status
dsl-slave-01 10.0.1.18 (NA)
dsl-slave-02 10.0.1.34 ON LINE
dsl-slave-03 10.0.1.50 ON LINE
dsl-slave-04 10.0.1.66 (NA)
dsl-slave-05 10.0.1.82 (NA)
dsl-slave-06 10.0.1.98 ON LINE

Version: 1.2
Quick Start Guide for VigorAccess IVD
4
How to Check the Version Information
To display the basic information of the
controller inside the master device The results
1. Login through terminal emulator software.
2. Type the following command
- Admin > system basic
You will get the following results:
-Admin> system basic
--------------------------------------------------------------------------------
SYSTEM BASIC INFORMATION
--------------------------------------------------------------------------------
Machine Model : IVD MASTER
Firmware Version : V3.1.17.16
Hardware Version : 1.1 - 1 Fiber(s)
Build Time : Fri Jul 21 09:47:32 CST 2006
System Uptime : 3 days 17h:30m:38s
System Contact : [e-mail]
System Name : IVD
System Location : urlocation
CPU Usage : 01%
Memory Usage : 52%
Current Time : Mon Jan 05 01:30:19 1970
To display the IVD module information inside
slave device The results
1. Login the specified IVD slave module.
2. Type the following command to get the DSL
module information
- IVD>system basicinfo
You will get the following results:
- IVD/system> basicInfo
---------------------------------------------------------------
SYSTEM BASIC INFORMATION
---------------------------------------------------------------
Machine Model : IVD system
Firmware Version : IVD_VOIP_V1.0.1.9
Hardware Version : V1.0
Build Time : Mon Jan 15 15:09:43 CST 2007
System Uptime : 0 days 05h:49m:43s
System Contact : [e-mail]
System Name : IVD
System Location : urlocation
Memory Usage : 41%
Current Time : Thu Jan 01 05:49:43 1970
To display the DSL module information inside
the IVD slave device The results
1. Login the specified DSL module.
- IVD>dsl –c (Connect to dsl device via
serial port)
2. Type the following command to get the
DSL module information
- $get system info
You will get the following results:
$get system info
Description : IP DSLAM
Name : IPDSLAM
Location :
Contact :
Vendor :
LogThreshold : 0
Object-id : 1.3.6.1.4.1.7367.2.11.1
Up Time(HH:MM:SS) : 140:49:31
HwVersion : 1.2

Version: 1.2
Quick Start Guide for VigorAccess
5
CPSwVersion : A24-A-1GE-2.10.2.8
DPSwVersion : DP_B02_10_14_60_ip1000a
System Time : Tue Jan 06 23:39:02 1970
Time Zone : GMT
DST : off
How to Save the Configuration
To save the configuration for the controller To save the configuration for the DSL module
Type the following command to save the
configuration.
- Admin>commit (Master)
- IVD>commit (IVD slave)
Note –
For VoIP functions, users need to
activate it by manual as following
command.
- IVD/voip>config activate
Type the following command to save the
configuration.
- $commit

Version: 1.2
Quick Start Guide for VigorAccess IVD
6

C
Co on nf fi ig gu ur ra at ti io on n b by y U Us si in ng g T Te el ln ne et t
To use Telnet for managing Master/Slave device, refer to the following sections.
Default IP Settings for Master Device Default IP Settings for Slave Device
1. The default IP address of Outband (MGN port):
172.16.1.1/255.255.255.0)
2. IP address for Inband (UPLINK port): 0.0.0.0
(disable)
1. The default IP address of Outband (MGN port):
172.16.1.2/255.255.255.0)
2. IP address for Inband (UPLINK port): 0.0.0.0
(disable)
How to Change Master IP Setting
Changing master IP address setting (for management) is allowed to suit environment requirement.
Type the command below to change the settings.
For Outband (MGN port connection) , please set as the following
- Admin>network out <new-ip> <mask> [vlanid]
For Inband (UPLINK port connection) , please set as the following
- Admin>network in <new-ip> <mask> [vlanid]
For the Status, please set as the following
- Admin>network out or - Admin>network in
Note: The IP addresses for MGN port and UPLINK ports cannot belong to the same domain.
How to Change Slave IP Setting
Changing IVD IPaddress setting (for management) is allowed to suit environment requirement.
Type the command below to change the settings.
For MGN/UP port connection , please set as the following
- IVD>network staticIP <ip> <netmask> <gateway>
Note:It is applied below version V1.0.1.7, MGN and UP will be different when the
version is above V1.0.1.7.
For the Status, please set as the following
- IVD>network staticIP -s
How to Configure IP Address for Slave-Standalone DSL module
A slave device can work alone without connecting the master device. The device with one Gigabit
Ethernet interface version.
For one gigabit-ethernet interface version, please set as the following
- $ipconfig <ip> <mask>
How to Login with Telnet
For Master/Slave Device
1. Make sure the device IP has been configured well.
2. Make sure the connection between MGN port (for outband) and UPLINK port (for inband).
3. Open Telnet command screen.
4. Username/Password
- admin/1234 (type ‘exit’to return)
Now, please use Telnet commands to manage the master/slave device for your necessity.

Version: 1.2
Quick Start Guide for VigorAccess
7
How to Set G5 and G6 as UPLINK Interface
For the environment with available Fiber
connection, the UP-G1/UP-G2 connector in
Master device is used as the channel to access
Internet. For such condition, you can connect
slave devices from G1 to G6.
However , for the environment without available
Fiber connection, G5 and/or G6 in Master device
can be used as the channel to access Internet. For
such condition, only G1 to G4 connectors can be
used for the slave devices.
For example,
- Admin>system uplink G6 up
Enable the port by typing:
- Admin>system link –m G6 on

Version: 1.2
Quick Start Guide for VigorAccess IVD
8

R
Re ef fe er re en nc ce e – – C Co om mm mo on n U Us se e C Co om mm ma an nd ds s f fo or r C Co on nf fi ig gu ur ra at ti io on n
P
Pa ar rt t I I: :
Here provides some general and common commands used in IVD for users to configure the IVD Master.
How to configure Inband IP Address
Users can use the following commands to configure the inband IP address for the UP-LINK interface or
inband management.
Command Description
Admin> network
Enter network directory
Admin/network> inband ?
Help
Admin/network> inband -s
Display the settings
Admin/network> inband <IP_addr>
<NetMask>
Edit the inband IP address without VLAN
Admin/network> inband <IP_addr>
<NetMask> <vlan_id>
Edit the inband IP address with VLAN
How to configure Outband IP Address
Users can use the following commands to configure the outband IP address for outband management.
Command Description
Admin> network
Enter network directory
Admin/network> outband ?
Help
Admin/network> outband -s
Display the settings
Admin/network> outband <IP_addr>
<NetMask>
Edit the outband IP address without VLAN
Admin/network> outband <IP_addr>
<NetMask> <vlan_id>
Edit the outband IP address with VLAN
How to configure Static Route
Users can use the following commands to configure the default route and some static routes.
Command Description
Admin> network
Enter network directory
Admin/network> route ?
Help
Admin/network> route –r
Display the routing table
Admin/network> route -s
Display the static route entries
Admin/network> route default <RtIP>
Add a default route
Admin/network> route default 0.0.0.0
Delete the default route

Version: 1.2
Quick Start Guide for VigorAccess
9
Admin/network> route -a <TargetIP>
<NetMask> <GatewayIP>
Add a static route entry
Admin/network> route -e <RtIdx>
<TargetIP> <NetMask> <GatewayIP>
Edit the static route entry
Admin/network> route -d <RtIdx>
Delete the static route entry
Admin/network> route -D
Delete all static route entries
How to configure NTP and Time
Users can use the following commands to configure the NTP server IP , the polling interval, time zone and
the daylight saves time. Users can enable/disable NTP function, too.
Command Description
Admin> service
Enter service directory
Admin/service> ntp –s
Display the settings
Admin/service> ntp ?
Help
Admin/service> ntp now
Display the current time
Admin/service> ntp -e <IP_addr>
<interval>
Edit the NTP server IP address and the polling
interval
Admin/service> ntp -t <MMDDhhmmYYYY>
Edit the year, month, date, hour, and minute.
Admin/service> ntp -z <time_zone> <DST>
Edit the time zone and the daylight saving time.
Admin/service> ntp on/off
Turn on/off the NTP
How to configure SNMP
Users can use the following commands to configure the SNMP settings, including SNMP community,
SNMPTrap port, and SNMPTrap host. After the following setting, EMS can communicate with IVD via
SNMP.
Command Description
Admin> service
Enter service directory
Admin/service> snmp -l
Display the general SNMP settings
Admin/service> snmp -s
Display the SNMPTrap host entries
Admin/service> snmp -c <CommRO>
<CommRW> <CommTrap>
Edit the read-only, read-write, and trap community
Admin/service> snmp -a <HostIP>
Add a trap host
Admin/service> snmp -e <EntryIdx>
<HostIP>
Edit the trap host
Admin/service> snmp -d <EntryIdx>
Delete the trap host entry
Admin/service> snmp –D
Delete all the trap host entries

Version: 1.2
Quick Start Guide for VigorAccess IVD
10
How to Upgrade Firmware
Users can use the following commands to upgrade new firmware. Make sure you have prepared a TFTP
server on a host and put the firmware (ivd.all for example) in the right directory of the TFTP server
Command Description
Admin> system
Enter system directory
Admin/system> upgrade <ServIP>
<FirmName>
Execute the firmware upgrading
Admin/system> reboot
Reboot the Controller to run the new firmware
Admin/system> basicInfo
After rebooting, check the firmware version
How to Save Configuration
Users can use the following command to save the current configuration.
Command Description
Admin> commit
Save the configuration
How to Enable/Disable the Switch Port
Users can use the following commands to enable or disable the port on Controller. By default, G1 to G6
are off, but G0 and UP-G are on. If users find that when they connect the subtend slave machines to the
master machine but the connection cannot be constructed, check the link status of the port connected to
the master machine is enabled.
Note: Ports G1 to G6 will be on with default if the DSL F/W version is above V2.10.2.6.
Command Description
Admin> system
Enter system directory
Admin/system> link_state -s
Display the current status of all ports
Admin/system> link_state -m <IntfName>
on/off
Turn on/off of the specific port
How to Connect to DSL Module
Users can login to DSLmodule in master or slave units using the following command. Once entering into
DSL module, the command described in Part II can be used.
Command Description
Admin> dsl
Display the current connectivity with DSLmodules
Admin> dsl –c
Login to DSL module in master via serial channel
Admin> dsl –m
Login to DSL modules in master via Ethernet channel
Admin> dsl –s <salveId>
Login to DSL modules in slave via Ethernet channel

Version: 1.2
Quick Start Guide for VigorAccess
11
P
Pa ar rt t I II I: :
Here provides some general and common commands used in IVD for users to configure the IVD DSL Module.
Note: Please refer to the Command Line Interface manual for getting more commands that IVD supports.
Contact your dealer for advanced information.
How to Monitor DSL Status
Users can use the following command to check the status for specified DSL port. The commands are listed
as below.
Command Description
$get adsl atuc physical ifname dsl-*
for downstream (*: 0 ~ 23)
$get adsl atur physical ifname dsl-*
for upstream (*: 0 ~ 23)
How to Enable/Disable a DSL Port
Users can use the following command to enable or disable DSL port for certain user. The commands are
listed as below.
Command Description
$modify adsl line intf ifname dsl-*
enable
Enable (*: 0 ~ 23)
$modify adsl line intf ifname dsl-*
disable
Disable (*: 0 ~ 23)
How to Read DSL Training Rate
Users can use the following command to read DSLTraining Rate for specified DSL port. The commands
are listed as below.
Command Description
$get adsl atuc channel ifname dsli-*
for downstream/interleave channel (*: 0 ~ 23)
$get adsl atur channel ifname dslf-*
for upstream/fast channel (*: 0 ~ 23)
$get adsl atuc channel ifname dsli-*
for downstream/interleave channel (*: 0 ~ 23)
$get adsl atur channel ifname dslf-*
for upstream/fast channel (*: 0 ~ 23)
How to Change ADSL Line Profile
Users can use the following command to change theADSL Line Profile for specified DSL port. The
commands are listed as below.
Command Description
$modify adsl line intf ifname dsl-*
disable
Disable (*: 0 ~ 23)
$modify adsl line profile ifname dsl-* ?
(*: 0 ~ 23, ?: means to get more information)
$modify adsl line intf ifname dsl-*
enable
Enable (*: 0 ~ 23)

Version: 1.2
Quick Start Guide for VigorAccess IVD
12
How to Change ADSL Line Rate
Users can use the following command to change theADSL Line Rate for specified DSL port. The
commands are listed as below.
Command Description
$modify adsl line intf ifname dsl-*
disable
Disable (*: 0 ~ 23)
$modify adsl line profile ifname dsl-*
atucintlmaxtxrate 0x7e0000
Necessary variables (*: 0 ~ 23)
$modify adsl line intf ifname dsl-*
enable
Enable (*: 0 ~ 23)
How to Change ADSL to Fast Channel/Rate
Users can use the following command to change theADSL to fast channel/rate for specified DSL port.
The commands are listed as below.
Command Description
$modify adsl line intf ifname dsl-*
disable
Disable (*: 0 ~ 23)
$modify adsl line profile ifname dsl-*
type fastOnly atucfastmaxtxrate
0x7e0000
Necessary variables (*: 0 ~ 23)
$modify adsl line intf ifname dsl-*
enable
Enable (*: 0 ~ 23)
How to Set ADSL Alarm Profile
Users can use the following command to change theADSLAlarm profile for specified DSL port. The
commands are listed as below.
Command Description
$modify adsl line intf ifname dsl-*
disable
Disable (*: 0 ~ 23)
$modify adsl alarm profile ifname
dsl-* ?
(*: 0 ~ 23, ?: means to get more information)
$modify adsl line intf ifname dsl-*
enable
Enable (*: 0 ~ 23)
How to Change VPI/VCI for Existing VCC
Users can use the following command to change VPI/VCI for existing VCC. The commands are listed as
below. We strongly recommend to delete original VCC then re-create a new VCC with new values again.
Command Description
$pvc delete <dsl: 1~24> <pvc: 1~8>
$pvc create <dsl: 1~24> <pvc: 1~8> <vpi>
<vci> [<llcmux|vcmux>]
[<interleaved|fast>]

Version: 1.2
Quick Start Guide for VigorAccess
13
How to Change Management IP Address for Existing Ethernet Port
Users can use the following command to change management IP address for existing uplink Ethernet port.
The commands are listed as below.
Command Description
$ipconfig <ip> <mask>
How to Create more VC/EOA/Bridge
Users can use the following command to create more VC/EOA/Bridge. The commands are listed as
below.
Command Description
$create atm vc intf ifname aal5-* vpi
<vpi> vci <vci> lowif atm-*
[vcmux/llcmux] [fast/interleaved]
(*:0 ~ 23 is used for atm; 0~191 is used for aal5)
$create eoa intf ifname eoa-* lowif
aal5-*
(*:0~191 is used for aal5 and eoa)
$create bridge port intf portid
<bridge-port-id> ifname eoa-*
(*:0~191 is used for eoa,; 1~192 is used for
<bridge-port-id>)
How to Setup SNMP Community/Host/Trap
Users can use the following command to setup SNMP community/host/trap. The commands are listed as
below.
Command Description
$snmpconfig <ro community> <rw
community> <trap community> <host ip>
Create SNMP community and host to manage the
device through SNMP
How to Create VLAN
Users can use the following command to create VLAN. The commands are listed as below.
Command Description
$create vlan static vlanname
<vlan-name> valnid <vlan-id>
[egressports <bridge ports>]
Create VLAN
(vlan-id is from 1~4094)
How to Setup Port VLAN ID (PVID)
Users can use the following command to setup port VLAN ID. The commands are listed as below.
Command Description
$modify gvrp port info portid
<bridge-port-id> portvlanid
<default-pvid>
Setup port VLAN ID

Version: 1.2
Quick Start Guide for VigorAccess IVD
14
How to Filter MAC Address by Port
Users can use the following command to filter MAC address by port. The commands are listed as below.
Command Description
$create acl port macentry portId
<bridge-port-id> macaddr
00:00:00:01:02:03
Allow source address 00:00:00:01:02:03 access from
bridge port; bridge-port-id means other source
addresses from bridge port <bridge-port-id> are
denied
$create acl port macentry portId
<bridge-port-id> macaddr
00:00:00:01:02:04
Allow source address 00:00:00:01:02:04 access from
bridge port; bridge-port-id means other source
addresses from bridge port <bridge-port-id> are
denied
How to Deny MAC Address Globally
Users can use the following command to deny MAC Address globally. The commands are listed as below.
Command Description
$create acl global macentry macaddr
00:00:00:01:02:03 deny enable
Mac source address 00:00:00:01:02:03,04 access
from any bridge ports is denied
How to Filter Net BIOS
Users can use the following command to filter Net BIOS. The commands are listed as below.
Command Description
$create filter rule entry ruleid <id>
action drop description NETBIOS-TCP
$create filter subrule tcp ruleid <id>
subruleid 1 srcportfrom 137 srcportto
139 srcportcmp inrange
$modify filter rule entry ruleid <id>
status enable
$create filter rule map ifname all
ruleid <id> stageid 1
$create filter rule entry ruleid <id2>
action drop description NETBIOS-UDP
$create filter subrule udp ruleid <id2>
subruleid 1 srcportfrom 137 srcportto
139 srcportcmp inrange
$modify filter rule entry ruleid <id2>
status enable
$create filter rule map ifname all
ruleid <id2> stageid 1
NETBIOS-NS: Name Service137 TCP/UDP
NETBIOS-DGM: Datagram Service 138 TCP/UDP
NETBIOS-SSN: Session Service 139 TCP/UDP
How to Enable Spanning Tree Protocol
Users can use the following command to enable spanning tree protocol. The commands are listed as
below.
Command Description

Version: 1.2
Quick Start Guide for VigorAccess
15
$modify stp info enable
Enable STP globally
$modify stp port info portid
<bridge-port-id> enable
Bridge port id: 1~193
$get stp port info portid
<bridge-port-id>
How to Enable IGMP Snooping
Users can use the following command to enable IGMP snooping. The commands are listed as below. Be
aware that IGMP Snooping is the Factory Default Setting.
Command Description
$create filter rule entry ruleid <id>
action sendtocontrol description IGMP
$create filter subrule ip ruleid <id>
subruleid 1 prototypefrom 2
prototypecmp eq
$modify filter rule entry ruleid <id>
status enable
$create filter rule map ifname all
ruleid <id> stageid 1
$modify igmpsnoop cfg info status
enable
$modify igmpsnoop port info portid
<bridge-port-id> status enable
leavemode fastNormal
or
$modify igmpsnoop port info portid
<bridge-port-id> status enable
leavemode Fast
The feature is enabled in default.
How to Upgrade Control Plane Code Remotely
Users can use the following command to remotely upgrade control plane code. Make sure you have
prepared TFTP server, vendor supplied CP.bin.gz , and put CP.bin.gz into root directory of TFTP server.
The commands are listed as below.
Command Description
$firmware upgrade [-]<source file>
<CP|DP|FD|DSL|ALL> <server ip>
Upgrade the control plane code

Version: 1.2
Quick Start Guide for VigorAccess IVD
16
How to Upgrade Full Image Remotely
Users can use the following command to remotely upgrade full image. Make sure you have prepared
TFTP server. The commands are listed as below.
Command Description
(Master)
Type command as below –
-Admin> system upgrade <tftp server ip>
<F/W file name>
<tftp server ip> IP address of TFTP server.
<F/W file name> ex. IVD_V3.1.17.2.all
(Slave – IVD module)
Type command as below –
-IVD> system upgrade <F/W file name>
<tftp server ip>
<tftp server ip> IP address of TFTP server.
<F/W file name> ex. IVD_VOIP_V1012.all
(Slave – DSL module)
1. Enter DSLmodule from IVD.
-IVD> dsl –c
Connect to DSL Console...
Press <Ctrl-\> or <Ctrl-Z> to return.
2. If current firmware version is below V2.10.2.4
1) Upgrade CP file
$firmware upgrade [-]<source file>
<CP|DP|FD|DSL|ALL> <server ip>
Example-
$firmware upgrade -CP-A24-A-1GE-2.10.2.8.bin.gz CP
<server ip>
2) Upgrade image file
Example-
$firmware upgrade -DSLImage-A24-A-1GE-2.10.2.8.all
ALL <server ip>
* If current firmware version is above V2.10.2.5
$firmware upgrade -DSLImage-A24-A-1GE-2.10.2.8.all
ALL <server ip>
Switch CLI mode to DSL module.
<server ip> IP address of TFTP server.
$reboot
Reboot from Default mode