Draytek Vigor2600 plus Series User manual

1
Vigor2600 plus Series introduction
LED Indicators and
Back Panels
Each of the Vigor2600 plus series router has different front and rear panels. Before you
begin to install, please take a moment to become more familiar with the LEDindicators and
rear panels. The following sections describe the models individually.
The Vigor2600 plus series is an Internet access solution for your LAN which not only provides shared web surfing
but countless other value-added features such as Firewall / Security, VPN, multimedia support, USB interface
printer server, and 54Mbps 802.11g Wireless LAN and all in a reliable one-box solution.
Annex A / Annex B
ISDN Backup
Wireless AP
ADSL Routers
Vigor2600i Vigor2600Gi
*
* / *
*
* / *
Vigor2600plus
*
* / *
_
Vigor2600G
* / *
_*
*
*
_
*
*
_

2
LED Indicators Descriptions
Descriptions
Back Panels
Vigor2600plus
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
P1, P2,
P3, P4
These indicators are dual-colour LEDs:
- OFF indicates that no device is connected to the LAN port.
- Yellow means the port is connected to a 10Mbps device.
- Green indicates to connected device is 100Mbps.
- BLINKING indicates that Ethernet packets are passing through the port.
PWR
Printer USB socket to connect a printer with USB interface.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
ADSL To connect to the ADSL-enabled telephone line.
ON when the QoS function is active.
QoS
Printer ON when the USB interface printer is ready
VPN
Blinking when the router suffers from the Dos(Denial of Service) attacks.
ATK
ON when the VPN is active.
ADSL
LINE
DATA
ON when the ADSL network is show time.
Blinking indicates the DSL protocols start hankshaking.
The light will remain still when data transmission is available.

3
LED Indicators Descriptions
Descriptions
Back Panels
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
VPN ON when the VPN is active.
PWR
Printer USB socket to connect a printer with USB interface.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory default
configuration.
Factory Reset
Vigor2600i
ADSL To connect to the ADSL-enabled telephone line.
Printer ON when the USB interface printer is ready
Blinking when the router suffers from the Dos(Denial of Service) attacks.
ATK
ADSL
LINE
DATA
ON when the ADSL network is show time.
Blinking indicates the DSL protocols start hankshaking.
The light will remain still when data transmission is available.
P1, P2,
P3, P4
LAN
These indicators are dual-colour LEDs:
- OFF indicates that no device is connected to the LAN port.
- Yellow means the port is connected to a 10Mbps device.
- Green indicates to connected device is 100Mbps.
- BLINKING indicates that Ethernet packets are passing through the port.
ISDN ON when the ISDN network is correctly setup.
BLINKING when there is a successful remote connection on the ISDN BRI B1 / B2
channel.
Note: for some NT-I boxes, the ISDN LED light will go OFF when the ISDN line has
been idle a while. When the router is dialling or answering a call it will go ON again
ISDN Connected to an external NT1(or NT1+) box provided by your ISDN service provider.

4
LED Indicators Descriptions
Descriptions
Back Panels
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
P1, P2,
P3, P4
PWR
Printer USB socket to connect a printer with USB interface.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
These indicators are dual-colour LEDs:
- OFF indicates that no device is connected to the LAN port.
- Yellow means the port is connected to a 10Mbps device.
- Green indicates to connected device is 100Mbps.
- BLINKING indicates that Ethernet packets are passing through the port.
To connect analog phone.
ADSL To connect to the ADSL-enabled telephone line.
ON when the QoS function is active.
QoS
V1, V2
Printer ON when the USB interface printer is ready
VPN
ON when the wireless LAN is ready.
ON when the VPN is active.
ADSL
LINE
DATA
ON when the ADSL network is show time.
Blinking indicates the DSL protocols start hankshaking.
The light will remain still when data transmission is available.
Vigor2600G
WLAN

5
LED Indicators Descriptions
Descriptions
Back Panels
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
VPN ON when the VPN is active.
PWR
Printer USB socket to connect a printer with USB interface.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory default
configuration.
Factory Reset
ADSL To connect to the ADSL-enabled telephone line.
Printer ON when the USB interface printer is ready
ADSL
LINE
DATA
ON when the ADSL network is show time.
Blinking indicates the DSL protocols start hankshaking.
The light will remain still when data transmission is available.
P1, P2,
P3, P4
LAN
These indicators are dual-colour LEDs:
- OFF indicates that no device is connected to the LAN port.
- Yellow means the port is connected to a 10Mbps device.
- Green indicates to connected device is 100Mbps.
- BLINKING indicates that Ethernet packets are passing through the port.
ISDN ON when the ISDN network is correctly setup.
BLINKING when there is a successful remote connection on the ISDN BRI B1 / B2
channel.
Note: for some NT-I boxes, the ISDN LED light will go OFF when the ISDN line has
been idle a while. When the router is dialling or answering a call it will go ON again
ISDN Connected to an external NT1(or NT1+) box provided by your ISDN service provider.
Vigor2600Gi
WLAN ON when the wireless LAN is ready.

6
Copyright
Declarations
Copyright 2003 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed, stored
in a retrieval system, or translated into any language without written permission from
the copyright holders.
The following trademarks are used in this document:
. Microsoft is a registered trademark of Microsoft Corp.
. Windows,Windows 95, 98, Me, NT, 2000, XP and Explorer are trademarks of
Microsoft Corp.
. Apple and Mac OS are registered trademarks of Apple Computer Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Trademarks
Safety Instructions
Warranty
. Read the installation guide thoroughly before you set up the router.
. The router is a complicated electronic unit that may be repaired only be authorized
and qualified personnel. Do not try to open or repair the router yourself.
. Do not place the router in a damp or humid place, e.g. a bathroom.
. The router should be used in a sheltered area, within a temperature range of +5 to +40
Celsius.
. Do not expose the router to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
. Keep the package out of reach of children.
. When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router wil be free from any
defects in workmanship or materials for a period of three (3) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it
serves as proof of date of purchase. During the warranty period, and upon proof of
purchase, should the product have indications of failure due to faulty workmanship
and/or materials, we will, at our discretion, repair or replace the defective products
or components, without charge for either parts or labor, to whatever extent we
deem necessary tore-store the product to proper operating condition. Any
replacement will consist of a new or re-manufactured functionally equivalent product
of equal value, and will be offered solely at our discretion. This warranty will not
apply if the product is modified, misused, tampered with, damaged by an act of God,
or subjected to abnormal working conditions. The warranty does not cover the
bundled or licensed software of other vendors. Defects which do not significantly
©

7
affect the usability of the product will not be covered by the warranty.We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any person of
such revision or changes.
European Community
Be A Registered
Owner
Firmware & Tools
Updates
Hereby, we declare that the router is in compliance with the essential requirements
and other relevant provisions of R&TTEDirective 99/5/EC.
Web registration is preferred. You can register your Vigor router via http://
www.draytek.com.tw . Alternatively, fill in the registration card and mail it to the
address found on the reverse side of the card.
Due to the continuous evolution of DrayTek ADSL & Router technology, all
routers will be regularly upgraded. Please consult the DrayTek web site for more
information on newest firmware, tools and documents.
http://www.draytek.com.tw

8
Vigor2600 plus Series Quick Start Guide
Identify your variant
Delivery check
Aim of this
chapter
Quickly connect your router to the Internet
Check your router package for the following items :
The Router
1 printed Quick StartGuide with warranty/ registration card
1 CDincludes detailed User Manual in electronic form, released firmware and
utilities
1 AC power supply adapter (black)
1 Ethernet LAN cable (blue) for connection to a computer or hub
1 ADSL line cable (RJ-11 to RJ-45 for Switzerland and the Netherlands only)
(RJ-11 to RJ-11 for other Annex A countries)
(RJ-45 to RJ-45 for Annex B countries)
1 ISDN line cable (RJ-45, black) for Vigor2600i and Gi only
2 external antennas for V2600G and V2600Gi only.
Please read page 9,10
Your router package should contain all these items. If any item is
missing or damaged, contact your dealer or our Customer Service
Department immediately.
The Vigor2600 puls series all containAnnex A/Annex B models,
please check if the package is suitble for your use by checking the
information from bottom of Vigor2600 plus series router.
Annex A : is for connecting to an analog POTS line
Annex B : is for connecting to a digital ISDN line

9
UK-type power adapter
CD
EU-type power adapter
AU/NZ-type power adapter
USA/Taiwan-type power
adapter
Manual

10
RJ-11 to RJ-11(Annex A)
RJ-11 to RJ-45(Annex B)
Dutch/Swiss User
RJ-45(Enternet)
RJ-45 to RJ-45
(Annex B,ISDN)
Filter/Splitter(Optional) Antennas for G/Gi only