Draytek Vigor2600VG User manual

1
Vigor2600 V Series introduction
LED Indicators and
Back Panels
Each of the Vigor2600 V series router has different front and rear panels. Before you begin
to install, please take a moment to become more familiar with the LED indicators and rear
panels. The following sections describe the models individually.
The Vigor2600 V series is an Internet access solution for your LAN which not only provides shared web surfing
but countless other value-added features such as Firewall / Security, VPN, multimedia support, USB interface
printer server, and 54Mbps 802.11g Wireless LAN and VoIP all in a reliable one-box solution.
Annex A / Annex B
ISDN Backup
Wireless AP
ADSL Routers
Vigor2600VG Vigor2600Vi
*
* / *
*
* / *
*
Vigor2600 V
*
* / *
_
Vigor2600VGi
* / *
_
VoIP * *
*_
* *
*
*
_*

2
LED Indicators Descriptions
Descriptions
Back Panels
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
P1, P2, P3, P4
VPN ON when the VPN is active.
These indicators are dual-color LEDs : Yellow means the port is connected to a
10Mbps device, and Green indicates the connected device is 100Mbps.
PWR
Printer To connect a USB based printer.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory default
configuration.
Factory Reset
LAN
ON when the connected network device has been linked up correctly. Blinking
when there are Ethernet packets passing through the switch port.
Vigor2600V
ON when the QoS function is active.
ON when you off hook the phone
Blink when a phone call coming
ON when the ADSL line is showtime.
To connect analog phone.
ADSL To connect the ADSL cable to your telephone jack.
ON when the USB interface printer is ready.
QoS
Phone(V1, V2)
Printer
LINE
V1, V2

3
LED Indicators Descriptions
Descriptions
Back Panels
Vigor2600VG
ON when the ADSL line is showtime.
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
P1, P2, P3, P4
WL
These indicators are dual-color LEDs : Yellow means the port is connected to a
10Mbps device, and Green indicates the connected device is 100Mbps.
PWR
Printer To connect a USB based printer.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
ON when the connected network device has been linked up correctly. Blinking
when there are Ethernet packets passing through the switch port.
To connect analog phone.
ADSL To connect the ADSL cable to your telephone jack.
ON when the QoS function is active.
QoS
ON when you off hook the phone
Blink when a phone call coming
Phone(V1, V2)
ON when the wireless LAN is ready
ON when the ADSL line is showtime.
LINE
ON when the USB interface printer is ready.Printer
V1, V2

4
Vigor2600VGi
P1, P2, P3, P4
WL
These indicators are dual-color LEDs : Yellow means the port is connected to a
10Mbps device, and Green indicates the connected device is 100Mbps.
PWR
Printer To connect a USB based printer.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
ON when the connected network device has been linked up correctly. Blinking
when there are Ethernet packets passing through the switch port.
ON when the ADSL line is showtime.
To connect analog phone.
ADSL To connect the ADSL cable to your telephone jack.
LED Indicators Descriptions
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
Blinking when thre is a successful remote connection on the ISDN BRI B1 /
B2 channel.
ON when the ISDN network is correctly setup.
Descriptions
Back Panels
Connected to an external NT1 (or NT1+) box provided by your ISDN service
provider.
Phone(V1, V2)
ON when the ADSL line is showtime.
ON when you off hook the phone
Blink when a phone call coming
ON when the USB interface printer is ready.
LNK
LINE
Printer
V1, V2
ISDN

5
Vigor2600Vi
ON when the ADSL line is showtime.
To connect analog phone.
P1, P2, P3, P4
VPN ON when the VPN is active.
These indicators are dual-color LEDs : Yellow means the port is connected to a
10Mbps device, and Green indicates the connected device is 100Mbps.
PWR
Printer To connect a USB based printer.
Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
ON when the connected network device has been linked up correctly. Blinking
when there are Ethernet packets passing through the switch port.
ON when the ADSL line is showtime.
V1, V2
ADSL To connect the ADSL cable to your telephone jack.
Blinking when thre is a successful remote connection on the ISDN BRI B1 /
B2 channel.
ON when the ISDN network is correctly setup.
LED Indicators Descriptions
Phone(V1, V2)
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
Descriptions
Back Panels
Connected to an external NT1 (or NT1+) box provided by your ISDN service
provider.
Connected to an external NT1 (or NT1+) box provided by your ISDN service
provider.
ON when the USB interface printer is ready.
ON when the ADSL line is showtime.
To connect analog phone.
ON when you off hook the phone
Blink when a phone call coming
ON when the USB interface printer is ready.
Blinking when thre is a successful remote connection on the ISDN BRI B1 /
B2 channel.
ON when the ISDN network is correctly setup.
LNK
LINE
Printer
ISDN

6
Copyright
Declarations
Copyright 2003 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed, stored
in a retrieval system, or translated into any language without written permission from
the copyright holders.
The following trademarks are used in this document:
. Microsoft is a registered trademark of Microsoft Corp.
. Windows,Windows 95, 98, Me, NT, 2000, XP and Explorer are trademarks of
Microsoft Corp.
. Apple and Mac OS are registered trademarks of Apple Computer Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Trademarks
Safety Instructions
Warranty
. Read the installation guide thoroughly before you set up the router.
. The router is a complicated electronic unit that may be repaired only be authorized
and qualified personnel. Do not try to open or repair the router yourself.
. Do not place the router in a damp or humid place, e.g. a bathroom.
. The router should be used in a sheltered area, within a temperature range of +5 to +40
Celsius.
. Do not expose the router to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
. Keep the package out of reach of children.
. When you want to dispose of the router, please follow local regulations on
conservation of the environment.
. When the 2600V contain FXS module, please do not connect V1,V2 ports with
phone line.
We warrant to the original end user (purchaser) that the router will be free from any
defects in workmanship or materials for a period of three (3) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it
serves as proof of date of purchase. During the warranty period, and upon proof of
purchase, should the product have indications of failure due to faulty workmanship
and/or materials, we will, at our discretion, repair or replace the defective products
or components, without charge for either parts or labor, to whatever extent we
deem necessary tore-store the product to proper operating condition. Any
replacement will consist of a new or re-manufactured functionally equivalent product
of equal value, and will be offered solely at our discretion. This warranty will not
apply if the product is modified, misused, tampered with, damaged by an act of God,
or subjected to abnormal working conditions. The warranty does not cover the
bundled or licensed software of other vendors.Defects which do not significantly
©

7
affect the usability of the product will not be covered by the warranty.We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any person of
such revision or changes.
European Community
Be A Registered
Owner
Firmware & Tools
Updates
Hereby, we declare that the router is in compliance with the essential requirements
and other relevant provisions of R&TTEDirective 99/5/EC.
Web registration is preferred. You can register your Vigor router via http://
www.draytek.com.tw . Alternatively, fill in the registration card and mail it to the
address found on the reverse side of the card.
Due to the continuous evolution of DrayTek ADSL & Router technology, all
routers will be regularly upgraded. Please consult the DrayTek web site for more
information on newest firmware, tools and documents.
http://www.draytek.com.tw

8
Vigor2600 V Series Quick Start Guide
Identify your variant
Delivery check
Aim of this
chapter
Quickly connect your router to the Internet
Check your router package for the following items :
The Router
1 printed Quick Start Guide with warranty/ registration card
1 CDincludes detailed User Manual in electronic form, released firmware and
utilities
1 AC power supply adapter (black)
1 Ethernet LAN cable (blue) for connection to a computer or hub
1 ADSL line cable (RJ-11 to RJ-45 for Switzerland and the Netherlands only)
(RJ-11 to RJ-11 for other Annex A countries)
(RJ-45 to RJ-45 for Annex B countries)
1 ISDN line cable (RJ-45, black) for Vigor2600Vi and VGi only
2 external antennas for 2600VG and 2600VGi only.
Your router package should contain all these items. If any item is
missing or damaged, contact your dealer or our Customer Service
Department immediately.
The Vigor2600 V series all contain Annex A/Annex B models,
please check if the package is suitable for your using.
You can get the information from bottom of Vigor2600 V
series router.
Annex A : connecting to an analog POTS line
Annex B : connecting to a digital ISDN line

9
Quickly connect your router to the Internet
UK-type power adapter
CD
EU-type power adapter
AU/NZ-type power adapter
USA/Taiwan-type power
adapter
Manual

10
RJ-11 to RJ-11(Annex A)
RJ-11 to RJ-45(Annex B)
Dutch/Swiss User
RJ-45(Enternet)
RJ-45 to RJ-45
(Annex B,ISDN)
Filter/Splitter(Optional) Antennas for VG/VGi only

11
What you
need from ISP
DSL Parameters
It should provide at least the following information from ISP :
1. The VPI/VCI of the virtual channel to use on the DSL line
2. Protocol : PPPoE, PPPoA or MPoA (RFC1483/2684)
3. Encapsulation Method : LLC/SNAP or VCMUX
4. Modulation Method : T1.413, G.lite, G.DMT
DSL line
Depending on the variant Vigor2600V series you purchased, the following DSL
service must be available at your local premisses:
ADSL over POTS [Annex A] :
ADSL service must be enabled on your POTS telephone line.
ADSL over ISDN [Annex B] :
ADSL service must be enabled on your ISDN telephone line.
(Vgior2600 Plus series provides Multimode which can automatically
detect)

12
Local networking
To use the Ethernet port(s) you need at least:
One PC with an Ethernet Card installed.
TCP/IP protocol suite
For TCP/IP, your PC can set either static IP or DHCP to ask IP from router. The
default gateway of router is 192.168.1.1. If static IP is chosen, you can set
192.168.1.x for your PC.
AWeb browser
Example:
VPI/VCI = 0/33
Protocol = PPPoA
Encapsulation Method = VCMUX
Modulation Method = G.DMT
Username/Password
Only for PPPoE/PPPoA mode users
Fixed IP Address/ Subnet Mask/ Gateway IP Address
Only for MPoA mode users. Some ISP will use DHCP method to provide IP
address for MPoA mode users, then users do not need to know the fixed IP
address.
If you do not know these information in detail, please contact your ISP to get
these informations.
What you need
in your side
VoIP
One analog telphone(FXS) or one telephone Line(Fxo).

13
Ethernet port (between router and PC), DSL port and Power port as below:
The wire installation

14
Install ‘ Router Tools ‘ This tool which provides “Smart StartWizard” Firmware Upgrade Program and
FTP client is in the attached CD. It supports Windows, Mac OS 8/9 and Mac OS
X. Moreover, it provides “Syslog Tool” for Windows system. For Vigor2600Vi /
VGi models, there is virtual TA program for the usage of ISDNAP.
Turn on your router Once all previous steps are completed, turn on your router. After Power is on,
theACT LEDand corresponding LAN port LED will light.
If the LEDs do not light normally, please refer to section A, “Trouble Shooting” for
further information.
Connect to router If the PC is set to obtain IP address automatically (recommended), you can use
Windows winipcfg.exe or ipconfig.exe to check if it has obtained an IP address from
the router. If not, please reboot PC and ensure that it has obtained an IP address from
the router.
Then you can use “Quick StartWizard” to config router or connect to router viaWeb
browser directly. The default IP of router is 192.168.1.1.

15
Once past the password prompt, you will now see the router’s main menu:
(Example: Vigor2600V)
Enter Router Menu
Set DSL Parameters Click on ‘Internet Access Setup’on the right-hand menu.
You will find three items : PPPoE/PPPoA ,MPoA (RFC 1483/2684), and Multi-
PVCs.
Password The default password is null. You can press “OK” to skip it.

16
For PPPoE/PPPoA
Users
Select your active PVC channel by Multi-PVC channel item.
Enter your allocated username, password according to the information provided by
your ISP.
If you want to connect to Internet all the time, you can check ‘Always On’.
Then click Multi-PVCs to Enter your DSL parameters according to the information
provided by your ISP. Please select "UBR" QoS Type if your ISP only support one
PVC channel on ADSL line.
Then you can continually enter setting menu according to the protocol which ISP
assigns.

17
For MPoA (RFC
1483/2684) Users
Select your active PVC channel by Multi-PVC channel item.
Enter your allocated WAN IP address(or enabling DHCP client to get IP from
ISP) and DSL parameters according to the information provided by your ISP.
Auto detect ATM/
DSL Setting
You can also use this function to detect ATM/ DSL setting. Please follow the
instructions to operate. If your country is not in the list, it may take longer time to
detect.
Click the "Internet Access Setup" option, and select "Auto DetectATM/DSL
Settings". Follow the prompts until it asks you whether you have a fixed IP or not, if
you are not then click Cancel.
Please select the country from the window. When you click OK it will go to detect
theATM/DSL setting.

18
Example for PPPoA:
It should now have detected the settings:
You can set/edit these manually when adding your ISP account details. Type in the
ISP name as well as the Username/Password provided by them. Also, you probably
want to tick the "Always On" box as there's no reason to disconnect the router when
you're not using the Internet. Ignore the fixed IP settings as an ISP will send then to
you each time you login anyway.

19
Surfing Internet Once all previous steps are completed, you can surf Internet now. You can also
monitor the connection condition via router management function.
(Example: Vigor2600V)
Wireless LAN
Setting
If you want to connect your wireless supported devices to Vigor2600VGi or
Vigor2600VG, you need to configure the router before you start to use it.

20
Wireless LAN
Interface
The Vigor2600VGi and Vigor2600VG are equipped with a wireless LAN interface
compliant with the 54Mbps IEEE 802.11g protocol. They are also interoperable with
802.11b compliant wireless devices. The features of wireless LAN
capability enable high mobility of several simultaneous users accessing all LAN facilities
just like on a wired LAN as well as Internet and WAN access.
The Frequency Domain is set as Europe and the MAC address will show as above. Click
General Settings, you could configure the SSID and wireless channel.
Scheduler: You can set wireless device to work at some time interval only. These are 4
internals you can choose: schedule1, schedule2, schedule3, and schedule4. The default
setting is always working. You can set the schedule under Advanced Setup >> Call
Schedule Setup. (Please refer to detail manual on the attached CD)