Draytek VigorSwitch G2260 User manual

V
Vi ig go or rS Sw wi it tc ch h G G2 22 26 60 0
2
24 4+ +2 2 G Gi ig ga a P Po or rt t
L
L2 2 M Ma an na ag ge ed d S Sw wi it tc ch
h
Quick Start Guide
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial
Park, Hsin-Chu, Taiwan 303
Product: VigorSwitch G2260
DrayTek Corp. declares that VigorSwitch G2260 is in compliance with the
following essential requirements and other relevant provisions of 2004/108/EC.
The product conforms to the requirements of Electro-Magnetic Compatibility
(EMC) Directive 2004/108/EC by complying with the requirements set forth in
EN55022/Class A and EN55024/Class A.
The product conforms to the requirements of Low Voltage (LVD) Directive
2006/95/EC by complying with the requirements set forth in EN60950-1.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class
A computing device pursuant to Subpart J of part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference when
operated in a commercial environment.
Version: 1.0
Date: 19/07/2012

nPackage Content
The 24+2 Giga Port L2 Managed Switch is a standard switch that meets all
IEEE 802.3/u/x/z Gigabit, Fast Ethernet specifications. The switch has 24
10/100/1000Mbps TP ports and 6 Gigabit TP/SFP transceiver slots.
The network administrator can logon the switch to monitor, configure and
control each port’s activity. In addition, the switch implements the QoS
(Quality of Service), VLAN, and Trunking. It is suitable for office
application.
VigorSwitch Rack Mount Kit
CD Ethernet Cable
The type of the power cord depends on the country that the router will be
installed:
UK-type power cord EU-type power cord USA-type power cord
Note: If any of these items is found missing or damaged, please contact
your local supplier for replacement.

oDescriptions of Panel
LED Explanation
LED Color Explanation
POWER Green Lit when +3.3V power is coming up.
TP Port 1– 24
(RJ45 LEFT)
LINK/ACT Green Lit when connection with remote device is good.
Blinks when any traffic is present.
TP Port 1– 24
(RJ45 RIGHT)
SPEED Green
Lit Green when TP connection with remote device is
1000M.
Blinks when TP connection with remote device is 100M.
Off when TP connection with remote device is 10M.
SFP Port 21-24
LINK/ACT
Green/
Amber
Lit Green when TP connection with remote device is
1000M..
Lit Amber when TP connection with remote device is
100M.
Blinks when any traffic is present.
SFP Port 25-26
LINK/ACT
Green/
Amber
Lit Green when the connection with remote device is
1000M.
Lit Amber when the connection with remote device is
100M.
Blinks when any traffic is present.
Connector Explanation
Interface Description
RESET Used to restart the device to default settings.
CONSOLE Used to perform telnet command control.
LAN P1 – P24 Giga Ethernet Port.
SFP (21 – 26) SFP Fiber Port.

p
Installing Your Switch
A hierarchical network with minimum levels of switch may reduce the timing
delay between server and client station. Basically, with this approach, it will
minimize the number of switches in any one path; will lower the possibility of
network loop and will improve network efficiency. If more than two switches
are connected in the same network, select one switch as Level 1 switch and
connect all other switches to it at Level 2. Server/Host is recommended to
connect to the Level 1 switch. This is general if no VLAN or other special
requirements are applied.
All switch ports are in the same local area network.
For other examples of hardware installation, please refer to User’s Guide for
detailed information.