Dream On Me 642 User manual

PAGE 1
MADE IN CHINA
DOUBLE BAR TODDLER
BED STYLE NO: 642
WARNING:
KEEP INSTRUCTIONS FOR FUTURE USE
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
CAUTION: BEFORE USING THIS TODDLER BED, RECHECK ALL
SCREWS TO BE SURETHAT THEY ARE TIGHTENED SECURELY.
A PERIODICAL CHECK SHOULD BE MADE TO CONFIRM THAT
ALL SCREWS & NUTS REMAIN TIGHT.
DO NOT SUSPEND STRINGS OVER THE TODDLER BED OR
ATTACH STRINGS TO TOYS.
CAUTION: ANY MATTRESS USED IN THIS TODDLER BED
MUST BE AT LEAST 51-5/8 INCHES(131CM) BY 27-1/4
INCHES (69CM) WITH A THICKNESS OF AT LEAST 4
INCHES(10CM) BUT NOT EXCEEDING 5 INCHES(12.5CM)
INFANTS CAN SUFFOCATIE IN GAPS BETWEEN CRIB
SIDES AND A MATRESS THAT IS TOO SMALL.
DREAM ON ME INC.
1532 S WASHINGTON AVE
PISCATAWAY TOWNSHIP
NJ 08854
TEL: [phone]
CUSTOMER CARE: [phone]

DO NOT PLACE THE TODDLER BED NEAR A WINDOW WHERE
CORDS FROM BLINDS OR DRAPES CAN STRANGLE A CHILD.
DO NOT TIE PACIFIER,NECKLACES,OR ANY OTHER
ITEMS AROUND A CHILD’S NECK OR ON THE PARTS
OF TODDLER BED.THIS COULD CAUSE
STRANGULATION.
DO NOT ADD A PILLOW, COMFORTER, OR PADDING,
INFANTS CAN SUFFOCATE ON SOFT BEDDING.
BEFORE EACH USAGE OR ASSEMBLY, INSPECT THE
TODDLER BED FOR DAMAGED HARDWARE,LOOSE
JOINTS,MISSING PARTS,OR SHARP EDGES.
DO NOT USE THE TODDLER BED IF ANY PARTS ARE
MISSING OR BROKEN.ASK YOUR DEALER OR WRITE
TO DREAM ON ME FOR REPLACEMENT OF THE PARTS
AND INSTRUCTIONAL LITERATURE IF NEEDED.
DO NOT SUBSTITUTE ANY PARTS.
IF REFINISHING,USE A NON TOXIC FINISH SPECIFIED
FOR CHILDREN’S PRODUCTS.TO CLEAN,WASH WITH
MILD SOAP AND A DAMP CHOTH.
TO STORE, KEEP IN A COOL, DRY PLACE.
DO NOT USE THE TODDLER BED IF THE SPACE
BETWEEN BED AND SOLID OBJECTS AS A WALL OR
DRESSER IS MORE THAN 12 INCHES(31CM).A CHILD
COULD SLIDE INTO A SMALL SPACE AND SUFFOCATE.
DO NOT USE THE TODDLER BED FOR INFANTS.THIS
TODDLER BED IS NOT A SUBSTITUTE FOR A CRIB.
THE TODDLER BED IS FOR A CHILD BETWEEN THE
AGE OF 15 MONTHS AND 5 YEARS WITH A MAXIMUM
WEIGHT OF 50 POUNDS(23KG).
DO NOT USE A WATER MATTRESS WITH THIS PRODUCT.
PAGE 2

(A) Headboard Leg 2PCS (B) Footboard Leg 2PCS
(C) Bed Rail 2 PCS
(L) Cross Middle
Bar 1 PC
(M) Cross Bar
8 PCS
(J) Side Bar
2 PCS
HARDWARE AND TOOL DIAGRAM
(a) Bolt 3” 18 PCS (b) Barrel Nut 18 PCS (c) Allen Wrench 1 PC
(d) Bolt 1-3/5” 12 PCS （e）1-3/5” Wood Dowel 20 PCS（f）Selfdrilling
screw 8 PCS
FLAT HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
- NOT INCLUDE
(h) L Metal Plate 2PCS
（C1)Right Bed Rail （C2)Left Bed Rail
COMPONENT PARTS
(K) Side Bar
2 PCS
(F) Split leg 2PCS
(k)
(g) Stopper 16PCS
PAGE 3
(A2) Right
(A1) Left (B2) Right
(B1) Left
(D) Headboard
slat 8 PCS
(E) Footboard
slat 8 PCS
(G) Top rail
2 PCS
(H) Bottom
rail 4 PCS
(J2) Right
(J1) Left
（j）2-2/5” Wood Dowel 4 PCS

(H)
PAGE 4
STEP# 1
STEP# 3
STEP# 2
STEP# 4
(H)
(D)
(g)
(A1)
(A2)
(G)
(H)
(H)
(H)
(H)
(E)
(g) (B1)
(B2)
(G)
(H)
(H)
(d)
(a)
(d)
(d)
(d)
(a)
(d)
(d)
(d)
(a)
(d)
(d)
(e)
(e)
(e)
(e)
(e)
(e)
(e)
(e)
(e)
(e)
Press the stopper(g) into the bottom
rail with warning label(H) with slat (D),
connect the slat(D) to the rail without
warning label (H).
Using the bolt (d) and the wood dowel
(e) to connect the left leg (A1) and right
leg (A2) to top rail(G) and rail (H);
Note: put the rail with waring label down
and inside that makes your crib better.
Press the stopper(g) into the bottom
rail (H) with slat (E), connect the slat
(E) to the rail (H).
Using the bolt (d) and the wood dowel
(e) to connect the left leg (B1) and right
leg (B2) to top rail(G) and rail (H);
Note: put the rail with waring label down
and inside that makes your crib better.
(a)
(b)
(b)
(b)
(b)

PAGE 5
(J2)
(j)
(j)
(J1)
(K)
(K)
STEP# 6
Connect the side bar (J1&J2) to the side bar (K) by L metal plates
(h) and selfdrilling screws (f).
Note: When attach the L metal plates (h), make sure the holes
on the L metal plates (h) match to the holes on the side
bar (J&K). Then tighten the selfdrilling screws (f).
(J1)
(K)
(f)
(f)
(f)
(f)
(J2)
(K)
(h)
(h)
STEP# 5
Connect the side bar (J1&J2)
to the side bar (K) by wood dowels (j).

Insert the cross bar (H&G) to the right side
bar (J2&K) .
(J2)
(K)
(M)
(L)
(M)
(F)
(a)
(b)
then attach the split
legs (F) to the cross middle bar(L)
by bolts (a) and barrel nuts (b).
PAGE 6
STEP# 7
Insert the cross bar (L&M) to the left side bar (J1&K).
then attach the split legs (F) to the cross middle bar(L)
by bolts (a) and barrel nuts (b).
(J1)
(K)
(L)
(M)
(M)
(F)
(a)
(b)
STEP# 8
(M)
(M)
(M)
(M)
(M)
(M)
(M)
(M)
(M)
(M)
(M)
(M)

PAGE 7
STEP# 10
Connect the side bar (K) to the footboard
Leg (B1) by using bolts (a) and barrel
nuts (b) .The footboard leg (B2) use the
same way.
(B2)
(B1)
(K)
(K)
(a)
(a)
STEP# 9
Connect the headboard Leg (A1) to the
left side bar (J1) using bolts (a) and
Barrel Nuts(b).The right side bar (J2)
use the same way.
(b)
(a)
(J2)
(J1)
(A2)
(A1) (a)

PAGE 8
STEP# 11
1.Connect left bed rail (C1) to the left side bar (J1)
using bolt (d),Then connect the left bed rail (C1)
to the headboard leg (A1) by using bolts (a)&(d)
and barrel nut (b).
(a)
(A1)
(a)
(d)
(d)
(A2)
(C1)
(C2)
(b)
(d)
(d)
(J1)
(J2)
2.Connect right bed rail (C2) to the right
side bar (J2) using bolt (d),Then connect
the right bed rail (C2) to the headboard
leg (A2) by using bolts (a)&(d)
and barrel nut (b).