Dream On Me 643 Guide

WARNING:
KEEP INSTRUCTIONS FOR FUTURE USE
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
CAUTION: BEFORE USING THIS TODDLER BED, RECHECK ALL
SCREWS TO BE SURETHAT THEY ARE TIGHTENED SECURELY.
A PERIODICAL CHECK SHOULD BE MADE TO CONFIRM THAT
ALL SCREWS & NUTS REMAIN TIGHT.
DO NOT SUSPEND STRINGS OVER THE TODDLER BED OR
ATTACH STRINGS TO TOYS.
1
MADE IN CHINA
STYLE NO: 643
CAUTION: ANY MATTRESS USED IN THIS
TODDLER BED MUST BE AT LEAST 51-5/8
INCHES (131CM) BY 27-1/4 INCHES ( 69CM )
WITH A THICKNESS OF AT LEAST 4 INCHES
( 10CM ) BUT NOT EXCEEDING 5 INCHES
(12.5CM).INFANTS CAN SUFFOCATE IN
GAPS BETWEEN CRIB SIDES AND A
MATRESS THAT IS TOO SMALL.
DOUBLE BAR TODDLER
BED WITH DRAWER
DREAM ON ME INC.
1532 S WASHINGTON AVE
PISCATAWAY TOWNSHIP
NJ 08854
TEL: [phone]
CUSTOMER CARE: [phone]

DO NOT PLACE THE TODDLER BED NEAR A WINDOW WHERE
CORDS FROM BLINDS OR DRAPES CAN STRANGLE A CHILD.
DO NOT TIE PACIFIER,NECKLACES,OR ANY OTHER
ITEMS AROUND A CHILD’S NECK OR ON THE PARTS
OF TODDLER BED.THIS COULD CAUSE
STRANGULATION.
DO NOT ADD A PILLOW, COMFORTER, OR PADDING,
INFANTS CAN SUFFOCATE ON SOFT BEDDING.
BEFORE EACH USAGE OR ASSEMBLY,INSPECT THE
TODDLER BED FOR DAMAGED HARDWARE,LOOSE
JOINTS, MISSING PARTS,OR SHARP EDGES.
DO NOT USE THE TODDLER BED IF ANY PARTS ARE
MISSING OR BROKEN.ASK YOUR DEALER OR WRITE
TO DREAM ON ME FOR REPLACEMENT OF THE PARTS
AND INSTRUCTIONAL LITERATURE IF NEEDED.
DO NOT SUBSTITUTE ANY PARTS.
IF REFINISHING,USE A NON TOXIC FINISH SPECIFIED
FOR CHILDREN’S PRODUCTS.TO CLEAN,WASH WITH
MIL SOAP AND A DAMP CHOTH.
TO STORE, KEEP IN A COOL, DRY PLACE.
DO NOT USE THE TODDLER BED IF THE SPACE
BETWEEN BED AND SOLID OBJECTS AS A WALL OR
DRESSER IS MORE THAN 12 INCHES(31CM). A CHILD
COULD SLIDE INTO A SMALL SPACE AND SUFFOCATE.
DO NOT USE THE TODDLER BED FOR INFANTS.THIS
TODDLER BED IS NOT A SUBSTITUTE FOR A CRIB.
THE TODDLER BED IS FOR A CHILD BETWEEN THE
AGE OF 15 MONTHS AND 5 YEARS WITH A MAXIMUM
WEIGHT OF 50 POUNDS(23KG).
DO NOT USE A WATER MATTRESS WITH THIS PRODUCT.
2

3
COMPONENT PARTS
(A) Headboard Leg 2PCS
(B) Footboard Leg 2PCS
(A2) Right(A1) Left
(B2) Right(B1) Left
(C) Bed Rail 2 PCS
(C1) Left (C2) Right
(D) Headboard Slat
8PCS
(E) Footboard Slat
8PCS
(F) Split Leg
2PCS
(G) Top Rail 2PCS
(H) Middle Rail 2PCS
(J) Bottom Rail 2PCS
(K) Side Bar 2PCS
(K2) Right
(K1) Left
(L) Side Bar 2PCS
(M) Cross Middle Bar
1PC
(N) Cross Bar 8PCS
(O) Slider 1PC
(P) Slider base 2PCS
(Q) Drawer Front Panel
2PCS
(R) Drawer Back Panel
2PCS
(S) Drawer Bottom
Panel 2PCS
(T) Drawer Side Panel 4PCS
(T2) Right
(T1) Left
(J1) Left
(J2) Right

4
HEADWARE AND TOOL DIAGRAM
(a) Bolt 3” 22PCS (b) Barrel Nut 22PCS (c) Allen Wrench 1PC
(d) Bolt 1-3/5” 14PCS (e) Wood Dowel 1-3/5” 28PCS
(f) 3/5” Selfdrilling Screws
8PCS
(g) Stopper 16PCS (h) L Metal Plate 2PCS
(m) Cam Bolt 16PCS
(k) Cams 16PCS
PHILLIPS-HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ---- NOT INCLUDE
STEP 1
Press the stopper (g) into the left
bottom rail with slide (J1) with slat (D).
Connect the slat (D) to the middle rail
(H).
(H)
(J1)
(D)
(g)
(j)

5
STEP 2
STEP 3
Using the bolt (a) ,barrel
nut (b) and the wood
dowel (e) to connect the
left leg (A1) and right leg
(A2) to top rail (G) .
Using the bolt (d) and the
wood dowel (e) to connect
the left leg (A1) and right
leg (A2) to middle rail (H)
and left bottom rail (J1).
Note: Put the rail with slide
down and inside that make
your crib better .
(G)
(H)
(J1)
(A1)
(A2)
(d)
(a)
(d)
(e)
(a)
(d)
(d)
(e)
(g)
(H)
(J2)
(E)
Press the stopper (g) into the
right bottom rail with slide (J2)
with slat (E).
Connect the slat (E) to the
middle rail (H).
(b)
(b)

6
STEP 4
STEP 5
(e)
(e)
(a)
(d)
(d)
(B1)
(a)
(d)
(d)
(B2)
(G)
(H)
(J2)
Using the bolt (a) ,barrel
nut (b) and the wood
dowel (e) to connect the
left leg (B1) and right leg
(B2) to top rail (G) .
Using the bolt (d) and the
wood dowel (e) to
connect the left leg (B1)
and right leg (B2) to
middle rail (H) and right
bottom rail (J2).
Note: Put the rail with
slide down and inside
that make your crib
better .
(e)
Connect the side bar (K1&K2) to
the side bar (L) by wood dowels
(e).
(K1)
(K2)
(L)
(L)
(e)
(b)
(b)

7
STEP 6
STEP 7
(f)
(h)
(f)
(f)
(f)
(h)
(K1)
(K2)
(L)
(L)
Connect the side bar (K1&K2) to
the side bar (L) by L metal plates (h) and selfdrilling screws (f) .
Note: When attach the L metal plates (h) ,make sure the holes on
the L metal plates (h) match to the holes on the side bar (K&L) .
Then tighten the selfdrilling screws (f) .
Insert the cross bar (M&N) to the left side bar (K1&L), then
attach the split leg (F) to the cross bar (M) and the slider (O) by
bolts (a), barrel nuts (b) and wood dowels (e) .
(a)
(a)
(a)
(e)
(b)
(K1)
(L)
(M)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(F)
(O)

8
STEP 8
STEP 9
Insert the cross bar (M&N) to the right side bar (K2&L), then
attach the split leg (F) to the cross bar (M) and the slider (O) by
bolts (a), barrel nuts (b) and wood dowels (e) .
(a)
(a)
(a)
(b) (b)
(b) (e)
(e)
(K2)
(L)
(M)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)
(F)
(O)
Connect the headboard (A1) to the left side bar (K1) using bolts
(a) and barrel nuts (b) . The right side bar (K2) use the same way .
(a)
(b)
(a)
(b)
(K2)
(K1)
(A1)
(A2)

9
STEP 10
STEP 11
Connect the side bar (L) to the footboard leg (B1) by using bolts
(a) and barrel nuts (b) . The footboard leg (B2) use the same way .
(a)
(B1)
(B2)
(a)
(b)
(L)
(L)
Put down the assembled parts as shown .
Then connect the slider base (P) to the assembled parts by using
bolts (a&d) and barrel nuts (b) .
(a)
(a)
(b)
(b)
(d)
(d)
(P)
(P)

10
STEP 12
STEP 13
1.Connect the left bed rail (C1)
to the left side bar (K1) using bolts
(d)．Then connect the left bed rail
(C1) to the headboard leg (A1) using bolts
(a&d) and barrel nuts (b) . 2.Connect the right
bed rail (C2) to the right side bar (K2) using bolts (d) .Then connect
the right bed rail (C2) to the headboard leg (A2) using bolts (a&d)
and barrel nuts (b) .
(a)
(a)
(b)
(d)
(d)
(d)
(d)
(K1)
(K2)
(C1)
(C2)
(A1)
(A2)
Attach both drawer right side (T2) and drawer
left side (T1) to the drawer back panel (R)
by inserting 4pcs cam bolts (m) to the end
holes of the drawer side panel (T) as shown .
Make sure the grooves line up and face inside.
Insert 4pcs cams (k) into the holes of drawer back panel (R) .
Lock the cams into the drawer back panel (R) using phillips-head
screwdriver .
(T2)
(T1)
(R)
(m)
(k)
(m)
(k)