Dream On Me 664 User manual

Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you
quickly assemble your products. Before you begin we recommend
that you following the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 664
1
s
Read all instructions before assembling crib.
Save instructions for future use.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788

2

.Read all instructions before assembling crib, keep instructions for future use.
.Upon completion of assembly be sure all screws, bolts and fastening devices have been
securely tightened. A frequent check should be made.
.Infants can suffocate in gaps between a mattress too small or too thick and product sides,
on soft bedding never add a mattress, pillow,comforter or padding.
.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8
inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the
.Failure to follow these warnings and the in structions could result in serious injury or death.
.Never use plastic shipping bag or other plastic film as mattress covers not sold and
intended for that purpose, they can cause suffocation .
.Strings can cause strangulation! Never place items with a string around a child’s neck,
.Never use this product if there are any loose or missing fasteners, loose joints,broken
parts, or torn mesh/fabric. check before assembly and periodically during use.
Contact DREAM ON ME for replacement parts and instructional literature if needed.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Discontinue use of the product when child is able to climb out or reaches the height of
.When child is able to pull to standing position,set mattress/base to lowest adjustment
positionand remove bumper pads, large toys ,and other objects that could serve as steps
for climbing out. A child can trap parts of the body or clothing on loose fasteners .
.Never use a water mattress with this product.
.If refinishing,use a non-toxic finish specified for children’s products.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
WARNING !
.Never place product near window where cords from blinds or drapes can strangle a child.
MADE IN CHINA
35in (890mm).
mattress shall be taken from seam to seam or edge to edge where appropriate.
such as hood strings or pacifier cords. Never suspend strings over product or attach
strings to toys.
.Infants can suffocate on soft bedding .
.Never add a pillow or comforter .
.Never place additional padding under an infant .
.To help prevent strangulation tighten all fasteners.
.A child can trap parts of the body or clothing on loose fasteners.
.Follow warnings on all products in a crib .
See head panel & mattress support of the product for warnings.
Replace teething rail if damaged,cracked or loose.
3

=
4
890

5
CONNECTION HARDWARE
CRIB COMPONENTS
A:Front rail (1pc) B:Back rail (1pc) C:Side rails (2pcs)
E:Left back leg (1pc)
F:Right back leg (1pc)
G:Left front leg (1pc)
H:Right front leg (1pc)
D:Mattress support (1pc)
AB
C
E
F
G
H
D
b:2-3/5”Allen head bolts (8pcs)
c:Barrel nuts (16pcs) d:Allen wrench (1pc) e:3/4”Allen head bolts (4pcs)
J:The bottom bar (1pc)
f:3”Allen head bolts (8pcs)
J
Do not use Power Drills or Drivers

6
STEP1
STEP2
Connect Left&Right back leg (E&F) to
Back rail (B) by Allen head bolts (f) ,
Barrel nuts (c) and Allen wrench (d) .
Connect Right front leg (H) to Side
rail (C) by Allen head bolts (b) ,
Barrel nuts (c) and Allen wrench (d) .
Assemble Left front leg (G) to the
other side rail in the same way .
f
c
c
c
c
c
c
b
b
B
E
F
C
H
d
d
f
f
f

7
STEP4
Locate the Mattress support (D)
with tabs . Be sure the smooth
side of the Mattress support is
faced upwared .
Position the tabs of the Mattress
support (D) to mount to the
selected position onto the legs .
Insert the bolts (e) through the
tabs and into thread inserts .
Then tighten securely with Allen
wrench (e) .
D
e
STEP3
Connect Side rails (C) to Left
&Right back legs (E&F)
by Allen head bolts (b) ,
Barrel nuts (c) and Allen
wrench (d) .
b
b
b
c
c
c
c
B
E
F
C
H
C
G
d
b

8
STEP5
Connect Front rail (A) to the
Left&Right front leg (G&H)
by Allen head board (f) ,
Barrel nuts (c) and Allen
wrench (d) .
TIGHTEN ALL THE BOLTS . A
G
H
c
f
f
f
f
c
c
c
c
d
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.
Converting crib to a toddler bed .
(toddler rail and converting bolts are sold separately)
c
c

9
5
！
Failure to follow these warning and the assembly instructions could result in
serious injury or death from entrapment or strangulation. DO NOT place
bed near windows where cords from blinds or drapes may strangle a child.
DO NOT place items witha string,cord,or ribbon around a child’s neck,such
as a hood, strings or pacifier cords. DO NOT suspend strings over a toddler
bed for any reason.
WARNING
The mattress intended for use on the bed shall be a full-size crib mattress
having the dimensions of 51-5/8” (1310mm) in length and 27-1/4”(690mm) in
width and thickness of 4” (100mm) or a greater thickness as specified by the
manufacture. The minimum age of the intended user shall not be less than
15 months and the maximum weight shall not be greaterthan 50lbs(22.7kg).
FOR TODDLER BED USE

10
Converting crib to a day bed
You have the option to convert crib to a day bed .
D
Converting crib to a full size bed I
Conversion kit is sold separately
You have the option to convert crib to a full size bed I
1:Remove the metal spring support platform (D),side rails(C).
2:Use the back rail (B) & the left back leg (E) & the right back
leg (F) as the headboard of full size bed.
3:Use the front rail (A) & the right front leg (G) & the right back
leg (H) as the footboard of full size bed.
4:Connect the footboard and headboard of adult bed to the
kits ( legs, long rails,and hardware ) which are not included
and sold separately.
1.Remove the Front rail (A),keep the screws for use of next step.
2.Assemble the bottom bar (J) to the Left&Right front leg (G&H) by
Allen head bolts (f)
,
Barrel nuts (c) and Allen wrench (d).
3.Install the Mattress Support (D) in its lowest position .
c
c
(Hollywood bed frame sold separately)