dreambaby Chelsea F160NB User manual

INSTRUCTIONS
Chelsea
CAUTION:
With any pressure mounted gate, a construction bar is required across the base. Note, this bar can be a tripping hazard. If you choose to
position a pressure mounted gate at the top of stairs, use extra caution to step over this bar to prevent trips and falls.
Can be used in conjunction with a Dreambaby®Watch-the-Step®Gate Ramp (F837) to help avoid tripping.
Item numbers may also end in BB.
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
If you sell or give away this product, make sure you give this instruction to the new owner.
• This product will not necessarily prevent all accidents. NEVER leave child unattended.
• Intended for use with children from 6 months through 24 months.
• This gate has an automatic close system.
• Do not use the safety gate if any components are damaged or missing.
• Ensure the surface you mount gate to is suitable for purpose and structurally sound such as solid timber,
brick or masonry.
• For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster/gyprock alone is not strong enough and not safe). Do not mount to glass.
• DO NOT install this gate to hollow walls.
• This gate is intended for indoor use and is not to be exposed to outdoor elements.
• Install this gate away from heaters and other sources of heat.
Children have died or been seriously injured
when gates are not securely installed.
• ALWAYS install and use gates as directed using all
required parts.
• You MUST install wall cups to keep the gate in place.
Without wall cups, child can push out and escape.
• STOP using when child can climb over or dislodge/open
the gate.
• Use only with the locking mechanism securely engaged.
• NEVER use to keep child away from pool.
WARNING
F160NB / F160NW
F190BN / F190NW
F170NB / F170NW
F191NB / F191NW
Chelsea I.M -F160N.F191N.F190N.F191N B/W p1-8_05.03.19_X.02
ASTM F1004
1

THE GAP IN THIS GATE IS NOT A FAULT.
The gap will disappear when the gate is correctly installed.
PLEASE INSTALL GATE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.
GAP
IMPORTANT NOTICE TO CUSTOMERS
IMPORTANTNOTICE
to Customers
Thegap in this gate is NOT a fault.
Thegap will disappear when the
gateis correctly installed.
Referto enclosed instructions for
correctinstallation procedures.
F - Gate Notice
Wood Screws
(Wood use only)
AGate Panel
BUpper Locking Set
CRelease Switch
DGate Frame
ETension Knobs
FBolts with Rubber Pads
GMounting Cups
HDouble-sided Adhesive Tape
ILower Locking Set
JWood Screws
PARTS LIST
AC B E
G
H
I
D
F
Jx 4
H x 4
G x 4 F x 4 E x 4
WARNING: This package contains small
parts and sharp points in an unassembled state. Keep
out of reach of children.
Adult assembly required.
TOOLS REQUIRED
Timber =
2mm (5/64in) drill bit
Brick/masonry =
5.5mm (7/32in)drill bit
2

F778 B/W
F782 B/W
F786 B/W
F788 B/W
F790 B/W
F792 B/W
F794 B/W
F796 B/W
F798 B/W
71-100cm
71-109cm
71-100cm
71-100cm
97-135cm
97-135cm
71-91cm
71-91cm
97-117cm
28-39in
28-42.5in
28-39in
28-39in
38-53in
38-53in
28-35.5in
28-35.5in
38-46in
Fits openings
KITS
F160 B/W +2 x F159(9cm/3.5in)
F190 B/W + F192(9cm/3.5in) +F193(18cm/7in)
2 x F160 B/W +2 x F159(9cm/3.5in)
2 x F190 B/W +2 xF192(9cm/3.5in)
F170 B/W + F159(9cm/3.5in) + F171(18cm/7in)
F191 B/W + F192(9cm/3.5in) + F193(18cm/7in)
F160 B/W + F159(9cm/3.5in)
F190 B/W + F192(9cm/3.5in)
F170 B/W + F159(9cm/3.5in)
K2
K2
K2
K1
K1
K1
K1
K1
K1
K1
K1
K1
&
&
&
&
&
&
&
&
&
&
&
&
1A 1B
1C 1D
71 - 82cm / 28 - 32in
71 - 82cm / 28 - 32in
75cm
(29.5in)
75cm
(29.5in)
F160B/ F160W F170B/ F170W
F190B/ F190W F191B/ F191W
97 - 108cm / 38 - 42.5in
97 - 108cm / 38 - 42.5in
1m
(39.5in)
1m
(39.5in)
1. Measure the width of the opening of where you intend to install the gate.
For wider openings select the appropriate Gate Extension(s),
sold separately.
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location (mounting on plaster/gyprock alone
is not strong enough and not safe).
DO NOT MOUNT TO GLASS.
INSTALLATION
3

K
Y
X
Z
Z
*
#159/#192 - 9cm (3.5in)
#171/#193 - 18cm (7in)
#172/#194 - 27cm (10.5in)
#831/#841 - 36cm (14in)
#832/#842 - 45cm (17.5in)
#833/#843 - 54cm (21in)
#834/#844 - 63cm (24.5in)
#835/#845 -100cm (39in)
2. Insert Extension pins into the holes on the outside of the Gate Frame.
Next, slip Extension Frames over the Pins.
Finally, slide the Tension Knobs and Bolts with Rubber Pads.
D
Gate Frame
E
Tension Knobs
F
Bolts with Rubber Pads
K
Extension Pin
L
Gate Extension
E
F
D
KK
L
L
Gate extensions
K
K1
K2
K3
DL
9cm (3.5in)
18 (7in) &
27cm (10.5in)
36 (14in)-100cm (39in)
A maximum of 4 Gate Extensions can be used, 2 on each side of gate. Do NOT install 3 Gate Extensions on the same side of gate.
WARNING
Insert SHORT END of EXTENSION PIN (K) into Gate Frame
D
KF
LEInsert LONG END of EXTENSION PIN (K) into Gate Frame
3.5in / 9cm
INSTALLATION Extension
K - Extension Pin
X - Lower Clamp
Y - Upper Clamp
Z - Connector Screws
Extension wider than 27cm / 10.5in
XZ
YZ
1. Install Lower Clamp X onto bottom of gate extension using Z.
2. Slip the gate extension over pins K.
3. Screw Upper clamp into place using Z.
4

Wood screws (J) included.
For Brick or Masonry use the appropriate fittings, screws and plugs
for your wall (not included)
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely flat
on the floor (3A), and it is perpendicular to the openings and the floor (3B & 3C).
4. Fasten the Mounting Cups to the wall with screws or double-sided adhesive tape (4A & 4B).
NOTE: Ensure that they are aligned vertically, so that the Mounting Cups at the top are directly above the ones at the bottom.
G x 4
H x 4
4A 4B
G x 4
H x 4
You MUST install wall cups
to keep the gate in place.
Without wall cups, child can
push out and escape.
If the safety barrier is used at the top of stairs,
it should not be positioned below the top
level.
At the top of landing, position the gate
15cm / 6in away from the top step.
If the safety barrier is used at the bottom of
the stairs, it should be positioned at the front
of the lowest tread possible.
Bottom of stairs
Floor
Top of stairs
Landing
15cm
6in
5. For use on stairs (5A & 5B).
3C
Side view of gate
3B
Top view of gate
Floor
Wall
Wall
Wall Wall Wall Wall
3A
INSTALLATION
Mounting cups must be screwed in
when using gate on stairs
5

6A 6B
EFEF
GG
7B 7C
Tighten inward
Apriete hacia
adentro
ED
Note: When first installing,
the gate will have this gap.
This is normal and will
disappear when gate is
completely installed.
7A
8A
Indicator Lines
6. Insert the Bolts with Rubber Pads and Tension Knobs into the Gate Frame, then partially slide the Bolts with Rubber Pads and Tension
Knobs outwards into the Mounting Cups (6A & 6B).
Keep this gap about 1mm / 0.04in
Mantenga un espacio de 1mm
8B
8. Tighten the Tension Knobs until the two Indicator Lines, located on the Upper Locking Set and on the Right Upper Corner,
align horizontally (8A).
Distance
should be
equal
When correctly tightened,
the distances between
Tension Knobs and Rubber
Pads should be equal (8B).
Y=Y
X=X
Y
X
Y
X
7. Tighten both of the bottom Tension Knobs by turning them at the same time (7A & 7B).
NOTE: Make sure the bottom of the gate frame remains completely flat on the floor.
Next, tighten both of the Tension Knobs at the top at the same time by turning them (7C).
INSTALLATION
Nota: La brecha (espacio
intermedio) en esta
compuerta no es un defecto.
La brecha desaparecerá
cuando la compuerta esté
correctamente instalada.
6

The warning line will disappear when the gate is locked properly.
The warning line will appear RED color if the gate is opened
or not locked properly.
RED
Release
Switch
Dispositivo
liberador
Slide / Corra
C
B
I
Gate opens in both directions
Lift Gate Panel up to open
A
AA
1A 1B 1C
2A 2B 2C
2D
1. To open the gate:
2. To close the gate:
Release the Gate and it will swing closed automatically.
Try this action several times and make sure:
• The Upper and Lower Locking sets are engaged (2A & 2B).
• The Warning Line has disappeared (2C & 2D).
OPERATION
Levante el panel de la compuerta hacia arriba La compuerta se abre con vaivén
en ambas direcciones
Warning line
7

Tee-Zed acknowledges that its customers may be
entitled to statutory consumer guarantees and does not
seek to exclude or limit them. These guarantees include
that Tee-Zed’s products are of acceptable quality. This
Tee-Zed product is for the specific purpose detailed in
the instructions and packaging and Tee-Zed considers
use outside of that purpose to be abnormal use. To the
maximum extent permitted by law, Tee-Zed does not
accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products
other than in accordance with the supplied
installation and removal instructions; or
• arising under the law of tort or contract.
Made in Dongguan, China.
©2019 Tee-Zed Products Pty Ltd
Dreambaby
®
products by
Tee-Zed Products Pty Ltd,
PO Box 2022
Bondi Junction NSW 1355
Australia
 [phone]
 [e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd,
PO Box 64013
Botany Town Centre Auckland
New Zealand
 [phone]
 [e-mail]
www.dreambaby.co.nz
Tee-Zed Products Ltd,
PO Box 29227
Dunfermline, KY12 2DN
United Kingdom
 [phone]
 [e-mail]
www.dreambaby.co.uk
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check gate to ensure it is fitted properly and securely. Adjust as required.
• Regularly check tension knobs and rubber pads to make sure the gate is securely in place.
• Do not use the safety gate if any components are damaged or missing.
• To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water. Never clean with abrasive, ammonia based bleach based or spirit type
cleaners.
• If the gate does not stay in position or does not swing closed properly, the gate may not be installed properly.
Remove and re-install gate, make sure the gate is installed vertically.
• Indicator Lines must be correctly aligned.
Keep 1mm / 0.04in gap.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
MAINTENANCE & CARE
TOP VIEW OF GATE
To engage the Smart Stay Open System swing gate in
chosen direction to its maximum opening
Gate will stay open. Close as required.
CAUTION: Keep gate closed when children are present.
Gate in CLOSED position
Swing to OPEN positions
SMART STAYOPEN SYSTEM
8