dreambaby COSMOPOLITAN F2029 User manual

Item numbers may also end in BB.
SECURITY GATE
COSMOPOLITAN
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY
AND KEEP FOR FUTURE REFERENCE
If you sell or give away this product, make sure you give this instruction to the new owner.
INSTRUCTIONS
F2029
F2107
F2108
CAUTION:
With any pressure mounted gate, a construction bar is required across the base. Note, this bar can be a
tripping hazard. If you choose to position a pressure mounted gate at the top of stairs, use extra caution to
step over this bar to prevent trips and falls.
Can be used in conjunction with a Dreambaby
®
Watch-the-Step
®
Gate Ramp (F837) to help avoid tripping.
WARNING
WARNING - Incorrect installation can be dangerous.
WARNING - Do not use the safety barrier if any components are damaged or missing.
WARNING - The safety barrier must not be fitted across windows.
WARNING - Never use without wall cups.
Screws MUST always be used to install wall cups.
This safety barrier is for domestic use only.
This safety barrier is suitable for use with children up to 24 months of age.
Never use with a child able to climb or dislodge/open gate.
The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound.
If the barrier is to be used at the top of the stairs, it should not be positioned below top level.
If the safety barrier is used at the bottom of the stairs, it should be positioned at the front of the
lowest tread possible.
Ensure the surface you mount gate to is suitable for purpose and structurally sound such as solid timber,
brick or masonry.
This gate has a manual close system.
This gate is intended for indoor use and is not to be exposed to outdoor elements.
Install this gate away from heaters and other sources of heat.
This product will not necessarily prevent all accidents. Never leave child unattended.
Conforms to EN1930:2011
1

C
A
G
H
i
D
BEF
NOTICE TO CUSTOMERS
E x 4
G x 4
Fx 4
H x 4
J x 4
THE GAP IN THIS GATE IS
NOT A FAULT.
The gap will disappear when
the gate is correctly installed.
PLEASE INSTALL GATE ACCORDING TO
MANUFACTURER’S INSTRUCTIONS.
A Gate Panel
B Upper Locking Set
C Release Switch
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
G Wall Cups
H Double-sided Adhesive Tape
I Lower Locking Set
J Wood Screws
PARTS LIST
WARNING :
This package contains small parts and sharp points in
an unassembled state. Keep out of reach of children.
Adult assembly required.
GAP
IMPORTANT NOTICE
to Customers
The gap in this gate is NOT a fault.
The gap will disappear when the
gate is correctly installed.
Refer to enclosed instructions for
correct installation procedures.
F - Gate Notice
Wood Screws
Wood use only
2

F 2029
F 2107 F 2108
75 - 90cm / 29.5 - 35.5in
75 - 81cm / 29.5 - 32in
75 - 99cm / 29.5 - 39in
A maximum of 2 Gate Extensions can be used, 1 on each side of gate. Do NOT install 2 Gate Extensions on the same side of gate.
WARNING
INSTALLATION
1. Measure the width of the opening of where you intend to install the gate.
For openings over 33in / 84cm select the appropriate Gate Extension(s), sold separately.
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster/gyprock alone is not strong enough and not safe).
DO NOT MOUNT TO GLASS.
9cm / 3.5in 9cm / 3.5in 9cm / 3.5in
3

*F1981 - 9cm (3.5in)
F1982 - 18cm (7in)
F1983 - 27cm (10.5in)
Gate Extensions
(sold separately)
L
E
F
K
D
GATE EXTENSIONS sold separately.
DL
F
K
E
9cm / 3.5in
2. To use with Gate Extensions (sold separately).
KY
W
XZ
X
Z
Y
W
K
K
X
For Extensions over 36cm/ 14in
INSTALLATION
ADDING EXTENSION FRAMES
Insert SHORT END of EXTENSION PIN (K) into Gate Frame
Insert LONG END of EXTENSION PIN (K) into Gate Frame
DL
K
K1
K2
K3
9cm / 3.5in
18cm / 7in &
27cm / 10.5in
36cm / 14in —
100cm / 39in
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
K Extension Pin
L Gate Extension
INSTRUCTIONS:
1. Install Lower Clamp Xonto bottom of gate extension using Z.
2. Insert short end of Extension Pin Kinto gate frame.
3. Slip the gate extension over pin.
4. Screw Upper clamp Yinto place using W.
PARTS
K - Extension Pin
W - Screws
X - Lower Clamp
Y - Upper Clamp
Z - Connector Screw
9cm / 3.5in
Insert Extension Pins K into the holes on the outside of the Gate Frame D
Next, slip Extension Frames L over the Pins K .
Finally, slide in the Tension Knobs E and Bolts with Rubber Pads F .
4

3A
4A
4. Fasten the Wall Cups to the wall with screws AND double-sided adhesive tape (4A & 4B).
NOTE : Ensure that they are aligned vertically, so that the Wall Cups at the top are directly above the ones at the bottom.
3C
3B
4B
Floor
Wall
Wall
Wall Wall Wall
Wall
INSTALLATION
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely flat on the floor (3A), and it is perpendicular
to the openings and the floor (3B & 3C).
Jx 4
If the safety barrier is used at the
bottom of the stairs, it should be
positioned at the front of the lowest
tread possible.
5. For use on stairs (5A & 5B).
Bottom of stairs
Floor
Top of stairs
Landing
Side view of gateTop view of gate
If the safety barrier is used at the top of
stairs, it should not be positioned below
the top level.
At the top of landing, position the gate
6in (15cm) away from the top step.
Wood screws (J) included.
For Brick or Masonry use the appropriate fittings, screws
and plugs for your wall (not included)
Never use without wall cups.
Screws MUST always be used
to install wall cups.
G x 4
H x 4 J x 4
Never use without wall cups.
Screws MUST always be used
to install wall cups.
5
15cm
6in

6A 6B
4
3B
3B
EFEF
GG
7B
7A
7C
Indicator
Lines
8A
6. Insert the Bolts with Rubber Pads and Tension Knobs into the Gate Frame, then partially slide the Bolts with Rubber Pads and Tension
Knobs outwards into the Wall Cups (6A & 6B).
Keep this gap about 0.04in / 1mm
8B
8. Tighten the Tension Knobs until the two Indicator Lines (X), located on the Upper Locking Set and on the Right Upper Corner, align
horizontally (8A).
Distance
should be
equal
When correctly tightened,
the distances between
Tension Knobs and Rubber
Pads should be equal (8B).
Y=Y
X=X
7. Tighten both of the bottom Tension Knobs (E) by turning them at the same time (7A & 7B).
NOTE:
Make sure the bottom of the gate frame remains completely flat on the floor.
Next, tighten both of the Tension Knobs (E) at the top by turning them at the same time (7C).
INSTALLATION
NOTE:
When first installing,
the gate will have this gap.
This is normal and will
disappear when gate is
completely installed.
Tighten inward
DE
Y
X
Y
X
MAX
5.5cm
2.15in
MAX
5.5cm
2.15in
6

2B
B
A
A
I
2A
1B1A 1C
C
Gate opens in both directions
Lift Gate Panel up to open
Slide
Release
Switch
1. To open the gate:
2. To close the gate:
Make sure the Upper and Lower Locking sets are engaged (2A & 2B).
OPERATION
•TOP VIEW OF GATE
To engage the Smart Stay Open System swing gate in chosen direction to
its maximum opening.
Gate will stay open. Close as required.
Gate in CLOSED position
Swing to OPEN positions
SMART STAY-OPEN SYSTEM
CAUTION : Keep gate closed when children are present.
A
7

F2029.F2107.F2108 IM_COSMO_pages1-8_Pressure_Mounted_02.07.19_X.02
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check Tension Knobs, Rubber Pads and Wall Cups to make sure the gate is securely in place and closes correctly.
Adjust as required.
• To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water. Never clean with abrasive,
ammonia based bleach based or spirit type cleaners.
• Only use Dreambaby® spare parts. Any additional and replacement parts should be obtained from Tee-Zed Products.
MAINTENANCE & CARE
Tee-Zed acknowledges that its customers may be entitled to statutory consumer guarantees and does not seek to exclude or limit them. These
guarantees include that Tee-Zed’s products are of acceptable quality. This Tee-Zed product is for the specific purpose detailed in the instructions and
packaging and Tee-Zed considers use outside of that purpose to be abnormal use. To the maximum extent permitted by law, Tee-Zed does not accept
any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
Dreambaby
®
products by
Made in Hangzhou, China.
©2019 Tee-Zed Products Pty Ltd
Tee-Zed Products Pty Ltd
PO Box 2022,
Bondi Junction NSW 1355
Australia
 [phone]
 [e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013,
Botany Town Centre Auckland
New Zealand
� [phone]
 [e-mail]
www.dreambaby.co.nz
Tee-Zed Products Ltd
PO Box 29227,
Dunfermline, KY12 2DN
United Kingdom
� [phone]
 [e-mail]
www.dreambaby.co.uk
8