Drieaz Velo User manual

07-01837A F504/F505-115V 2013-03 Warranty 07-00419 1 Dri-Eaz Products, Inc.
Owner’s Manual
Velo™Low Profile Airmover
Velo™Pro Low Profile Airmover
Model F504-115V, F505-115V
DRI-EAZ PRODUCTS, INC.
15180 Josh Wilson Road, Burlington, WA 98233, USA
Phone: [phone] Fax: [phone] www.dri-eaz.com
The Velo Airmover produces a high rate of airflow to accelerate the
evaporation of moisture from materials for restorative drying.
Patents: http://www.LBpatents.com
READ AND SAVE THESE INSTRUCTIONS
WARNING! To reduce the risk of fire or
electric shock, do not use this fan with any
solid-state speed control device.
WARNING! Unit must be grounded. Do not use with
an extension cord. Connect only to an outlet provided with a
GFCI device.
WARNING! Never operate a unit with a damaged power cord, as
this may lead to electrical or fire hazards. If the supply cord is
damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
WARNING! Do not touch grills when unit is operating.
WARNING! Do not alter or modify your Velo in any way. Use
only replacement parts authorized by Dri-Eaz Products, Inc.
Modifications or use of unapproved parts could create a hazard
and will void your warranty. Contact your authorized Dri-Eaz
distributor for assistance.
NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not allow children to play with or around the unit.
Be sure the unit is inaccessible to children when not attended.
NOTICE: Always operate the unit on a stable, level surface so it
cannot fall and cause damage or injury.
PRODUCT FEATURES
Velo (F504) Velo Pro (F505)
Operating speed(s) 1 Variable
Operating positions 4 5 (with stand)
Fold-out stand ●
Carry handle ●●
Stackable for storage ●●
BEFORE YOU BEGIN
Warranty registration
Please visit warranty.drieaz.com to register your purchase.
Registration allows us to better assist you with using, maintaining
or servicing your equipment and to contact you in case we have
important safety information concerning your Dri-Eaz product. If
you determine service is required, have your equipment model,
serial number and original proof of purchase available and call
your distributor for assistance with obtaining a return material
authorization (RMA).
OPERATING INSTRUCTIONS
Note that the Velo can be placed in a variety of positions for
drying and air circulation. See Fig. B for details.
1. Unwrap the cord and plug the unit into a standard 115V
GFCI-protected outlet. CAUTION: Be sure switch is in the
off position before connecting unit to power outlet.
2. Aim the Velo outlet toward the surface to be dried.
Rear cord wrap under
bottom edge. Wrap
cord clockwise and
secure with plug clip.
On/Off switch.
(Variable speed
on F505 only)
Stand folds out
and locks (F505
model only.)
Inlet grill. Keep clear
of obstructions.
Outlet grill. Keep
clear of obstructions.
Circuit breaker reset switch
GFCI-protected
power outlet sockets
with reset switch.
Carry strap
Fig. A: Parts Identification
Front Lift/Cord Wrap tab.
Wrap cord clockwise and
secure with plug clip.

07-01837A F504/F505-115V 2013-03 Warranty 07-00419 2 Dri-Eaz Products, Inc.
3. When surface is dry to the touch, switch the unit off and
reposition the unit in the next area to be dried.
4. When finished, unplug the unit and re-wrap the cord in the
cord wrap.
For additional instructions about the use of airmovers for
restorative drying, visit www.DriEaz.com and
www.RestorationSciencesAcademy.com.
Electrical safety devices
Circuit breaker: If the circuit breaker detects overload or short
circuit conditions, the breaker will automatically shut off the
electrical supply. If this should occur, check the power cable
carefully for any damage and ensure it is plugged into a properly
grounded outlet. Press the “Reset” button (Fig. A) to reestablish
the electrical supply.
Ground Fault Circuit Interrupter:If the GFCI device detects a
ground fault, it will automatically shut off the electrical supply. If
this should occur, check the power cable carefully for damage
and ensure it is plugged into a properly grounded outlet. Press
the GFCI reset button (Fig. A) to reestablish the electrical supply.
Transport and Storage
Always use the handle to load or carry the unit.
Wrap cord in a clockwise direction under front Cord Wrap tab
and rear bottom edge (Fig. A). Pull cord snug and secure with
plug clip.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully to
prevent sliding and damage to the unit and/or injury to vehicle
occupants.
Keep unit dry. Do not expose the unit to rain or snow.
Maintenance
WARNING: Unplug unit before performing any maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.
As needed
Clean housing and impeller. If dust accumulation is visible,
remove the four screws from the top, then turn the unit on its
back and remove the six fasteners as shown (Fig. C). Lift off the
housing. Clean impeller assembly with pressurized air and/or
with a soft cloth. Do not apply liquids to the impeller assembly.
The housing may be cleaned with a mild solution of detergent
and warm water. Ensure housing is completely dry before
reassembling.
FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or the Dri-Eaz
Service Department at 800-932-3030.
Warranty information is available at http://www.dri-eaz.com.
Be sure to visit warranty.drieaz.com and register your purchase.
Your registration will help us provide you with updated product
information as needed.
SPECIFICATIONS
Model Velo (F504) Velo Pro (F505)
Weight 21 lbs. | 9.52 kg 21 lbs. | 9.52 kg
Dimensions
(D × W × H)
24 × 18 × 9 in.
61 × 45.7 × 22.9 cm
24 × 18 × 9 in.
61 × 45.7 × 22.9 cm
Amp draw 1.9 amps (115V) 1.2 – 1.9 amps (115V)
Power 185W 185W
Air movement 885 CFM
885 CFM (high)
500 CFM (low)
Sound level (avg.) 69 dB 69 dB
Control On/Off switch
Variable speed with
On/Off switch
Cord length 15 ft. | 4.6 m 15 ft. | 4.6 m
Fan 6 blades 6 blades
Construction
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
Specifications are subject to change without notice. Some values
may be approximate.
Fig. C: Disassembly
To disassemble for
cleaning, first remove
the four screws from the
impeller assembly A
(shown below), then
turn the unit on its back
and remove the six
screws from the base.
Lift off the housing.
Retain screws and
washers for reassembly.
A. Remove impeller
assembly screws (×4)
first.
Fig. B: Operating Positions
Horizontal (for
horizontal surfaces)
Vertical (for walls
and ceilings)
Right edge (for
wall drying)
Left edge (for
wall drying)
With stand
(Pro model only)