Drija LIVORNO 76 Professional User manual

User Manual
LIVORNO 76
Professionale
5 Burners

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
1
1. INTRODUCTION................................................................................................................. 2
2. SAFETY WARNING............................................................................................................ 2
3. INSTALLATION................................................................................................................... 5
4. CONNECTION.................................................................................................................... 6
5. INSTALLATION OPTIONS ................................................................................................. 9
6. INSTRUCTION FOR USE................................................................................................. 10
7. CLEANING AND MAINTENANCE.................................................................................... 12
8. TECHNICAL DATA........................................................................................................... 14
9. PROBLEM SOLVING .................................................................................................... 15

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
2
1.INTRODUCTION
Thank you for choosing our gas stove. To use this stove properly and to avoid any potential
risk, read these instructions before using it.
Keep these instructions in a place where they can be found easily. If you are not sure of any of
the information contained in these instructions, please contact our customer service center.
The manufacturer is not liable for damages to persons or property caused by improper
installation or misuse of your kitchen.
The device has been certified for use in countries other than those marked on the stove.
The manufacturer reserves the right to make modifications that it deems necessary or useful,
also in the interests of the user, without jeopardizing the main functional and safety features.
The stove is designed for a domestic and non-commercial environment.
2.SAFETY WARNING
FOR YOUR SECURITY
These instructions have been developed for your safety and that of others. Therefore,
you are asked to read carefully before installing and using the appliance. Keep this
instruction manual for future reference as needed. If the unit is sold or moved, make
sure that the manual is delivered to the new user.
INSTALLATION
• The installation and the electrical connection must only be carried out by qualified
personnel. Before carrying out any procedure, make sure that the appliance is
disconnected from electrical power.
• It is risky to modify or attempt to modify the characteristics of this product.
• After removing the gasket from the appliance, check that it is not damaged and that the
electrical conductor is in perfect condition. If you notice any mishaps, contact the dealer
before using the appliance.
• The manufacturer declines all responsibility in case of non-compliance with accident
prevention regulations.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
3
• Ensure that air can circulate freely around the appliance. Poor ventilation causes a
shortage of oxygen.
• Ensure that the appliance is supplied with the type of gas indicated on the label next to
the gas connecting pipe.
• The use of a gas cooking appliance produces heat and humidity in the room in which it is
installed. Ensure that the room is well ventilated, keeping the air intake open and in good
working condition or by installing an exhaust hood with the discharge tube.
• If the appliance is used intensively for a long time the effectiveness of the ventilation will
have to be increased, for example by opening a window or increasing the power of any
electric extractor hood.
DURING USE
This product was designed for home use and should not be used for other purposes.
Once the appliance is used, make sure the controls are closed or in the off position.
If you use an electrical outlet near the appliance, be careful that the appliance wires are
away from the hot parts of the appliance.
SAFETY FOR CHILDREN
This appliance should only be used by adults. Make sure children do not touch or play
with the control.
The external parts of the appliance tend to become warm during cooking and remain
warm for a time once it is switched off. Keep children away until fully cooled.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
4
SERVICE AND PARTS
• In case of malfunction. Never attempt to repair the appliance yourself.
• Repairs performed by inexperienced persons can cause damage and accidents. See the
contents of this manual. If you do not find the necessary information, contact your nearest
service center.
• This appliance must be serviced by an authorized service center.
• Always request the use of original spare parts.
TIPS ON ENVIRONMENTAL PROTECTION
• All materials used are environmentally friendly and recyclable. Please make your contribution
to the conservation of the environment by using the available collection channels.
OUTDOOR APPLIANCES
• Devices that are no longer usable are not waste of value, part of their parts can be reusable.
• Be aware of disposal options available from your dealer or local authorities.
• Before disposing of appliances, disconnect the power supply cable.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
5
3.INSTALLATION
For the proper functioning of a gas appliance, the air
necessary for the combustion of the gas must flow naturally
through the room. Air must flow directly into the room
through openings in the outside of the wall. These
openings must have a minimum obstruction of not less
than 2m3 / h for each kW of power (see total power in kW
on the appliance plate).
This opening must be constructed so that it is not
obstructed from the outside or inside, or constructed near
the floor. It is advisable that the opening is of the opposite
hand from where the discharge of the combustion gas is. If
it is not feasible to provide these openings in the room
where the appliance is installed, the necessary air must be
taken from an adjacent room provided that:
• The room is not a bedroom or a dangerous environment.
• The room has ventilation
That the ventilation between the room where the apparatus
is installed and the adjacent room has openings.
DISCHARGE OF COMBUSTION GAS
Gas cooking appliances should discharge their flue gas
through extractors connected directly to the flow or to the
outside.
If it is not possible to install the extractor (fig B) an electric fan
should be installed on the outside of the wall or the room
window wherever possible so that the ventilation opening
increases in proportion to the speed fan supply (fig. C). For the
kitchen, the rate of execution of the fan should ensure an air
exchange per hour of 3-5 times its volume.
In both cases it is prohibited to use tubes already used by
other devices to discharge the flue gases.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
6
4. CONNECTION
Connect to the gas system using a rigid metal pipe and fittings or a stainless steel hose that
meets the local standard. If metal hoses are used, be careful not to come into contact with the
moving parts. This should be checked if the burner is combined with the oven. The gas supply
pipe of the appliance has a "male thread." When connecting, be careful not to apply any
voltages to the appliance.
Once the installation is complete, make sure that all joints are fully adjusted using a soapy
solution. Never use flame to perform the check.
CONNECTION TO GAS SUPPLY
• The gas connection must be made in accordance with local standards.
• When installing, attach a safety cover to the end of the pipe.
• The manufacturer should leave the test label as well as the type of gas indicated for use
on the plate inside the safety button, close to the gas connection tube. Make sure that the
gas to be supplied is the same as that in the place. Otherwise, follow the instructions given
in the section "Adapting to other types of gas".
• For maximum efficiency and minimum consumption, make sure that the supplied gas
pressure complies with the values shown on the gas and is not different from those
specified or it’s variable. A pressure regulator must be installed in the supply pipe.
ELECTRIC CONNECTION
The unit must operate at 110V mono phase voltage. The connection must be in accordance
with the rules and regulations in force.
Before connecting, make sure that:
1) The safety of the switch and the electrical system are able to withstand the load of the
apparatus. (See plate).
2) The power supply system has a ground connection in good working order, in accordance
with current regulations.
3) The omnipolar switch is easily accessible with the appliance.
Insert a plug suitable for charging on the power cord and connect it to a safety outlet
If you want to make a direct connection to the mains, a switch
Omnipolar with a distance between the contacts of 3mm, suitable qualification for the load and
complying with the current regulations must be installed between the device and the Source.
There should be no breakage between the yellow / green ground contacts.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
7
The brown colored high voltage cable (connected to the "Terminal" of the terminal box) must
always be connected to the direct cable of the mains.
In all cases, the power cord must be placed so that a temperature of 50 ° above room
temperature is not reached.
See illustration. The cable is guided by means of fixed band clamps to one side of the box, in
order to avoid any contact with the apparatus below the hob.
REPLACE POWER SUPPLY CABLE
If the cable has to be replaced, only cables of type H05RR-F or H05RN-F must be used for
charging and operating the temperature. In addition, the yellow / green ground wire should be
about 2cm longer than phase and neutral wires.
ADAPTING DIFFERENT TYPES OF GAS
Change of nozzles
1) Remove the pan support.
2) Remove burner covers and burner flames.
3) Use a size 7 screwdriver to remove the nozzles and replace them with the type that
corresponds to the gas used (see table).
4) Re-assemble the parts, following the same instructions given to the reverse.
5) Then replace the data (near the gas connection source) with the new gas type information.
If the pressure of the used gas is different from the one specified or its variable, a gas pressure
regulator must be installed that complies with the standards for the supply pipe.
MINIMUM LEVEL ADJUSTMENT
1) Turn on the burner as indicated.
2) Turn the faucet to the minimum flame position.
3) Remove control knobs.
4) Use a thin screwdriver to turn the bypass pin located near the faucet bar. (See Figure B).
For LPG gas, turn the bypass pin fully clockwise.
The result should be a small, but homogeneous flame which is uniform around the
surroundings of the burner ring. For the triple-A version see Fig. A. bypass 1 central burner,
bypass 2 both burners.
5) Finally, make sure that the burners are not turned off when the faucet is turned quickly from
the maximum to the minimum position.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
8
EMPOWERING IN KITCHEN UNITS
These plates are designed for installation in kitchen units with more than 600 mm depth with
the appropriate characteristics.
Any of the side panels of the cabinet higher than the height of the plate itself must be at least
150mm away from the opening in which the hob is inserted.
The dimensions of the hob and the installation opening are shown in the illustration.
INSERTION AND FIXATION
Before inserting the cook top into the installation
opening, place the special gasket around the
bottom edge of the cook top.
It is important to secure this joint evenly, without
voids, to prevent liquid seeping into the slots in
the plate.
1) Remove pan stand and burner cover and turn
over burner taking care not to damage ignition
plug and thermocouple.
.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
9
5. INSTALLATION OPTIONS
CABINETS WITH DOOR
When constructing the cabinet, care must be taken to avoid contact with the outside of the
burner, which becomes very hot during use. We recommend taking into account the
suggestions in fig.1
The panel below the burner should be easily removed to prevent blockage and can be
removed in the event of maintenance.
OVEN CABINETS
The installation compartment must have the dimensions shown in Figures 2 and 3 as well as
support allowing satisfactory ventilation. Two methods to avoid overheating are shown in
Figures 3 and 4. The electrical connection of the burner and the oven must be done
separately. Both for electrical reasons and to simplify moving the oven from the front of the
cabinet.
Wall or extractor cabinets should be at a height of 650mm per burner oak.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
10
Burner Description
• Burner
• Small auxiliary burner
• Burner control knobs
• Burner plate
• Quick burner
• Burner plate
• Burner plate
• Semi-fast burner
6. INSTRUCTION FOR USE
Burner control snobs
The symbols on the control knobs mean the following:
No gas flow
Maximum gas flow
Minimum gas flow
Every operation must be programmed between the flows
Maximum and minimum and never between the maximum and the closing position.
(Symbol present on models with integrated lights on the control knob).
• Burner cover
• Burner base
• Light switch
• Thermocouple
• Burner cup

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
11
DUAL TRIPLE FLAME VERSION
No gas flow
Maximum gas flow from central burner
Minimum gas flow from central burner.
Gas flow from outside and burner center simultaneously.
Minimum gas flow from outside and burner center simultaneously
BURNER IGNITION
• To obtain a flame, light the burner before placing the utensil on it.
• To light the burner, proceed as follows: For models with integrated light on the control
knob, push fully down and counterclockwise to the maximum flow symbol or press the
button if the appliance is on individual.
• Once the flame is switched on, press and hold the knob for about 10 seconds: This time is
necessary to set the thermocouple (Fig.1 - C) and activate the safety valve; otherwise the
gas flow will be cut off.
• Then check the flame and turn the control knob to adjust the flame to the desired level.
• In the event of a power failure, place a flame near the burner and proceed as described
above.
• If the flame does not come on after several attempts, check that the burner and flame
cover is in the correct position.
• To turn off the flame, turn the control knob clockwise to the symbol.
• Before removing any utensils from the burners, always lower or turn off the flame.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
12
FOR CORRECT USE OF BURNER
To reduce gas consumption and for efficient use, use flat-cut pans with dimensions appropriate
to the burner, as shown in the table to the right. Also, as soon as the liquid begins to boil lower
the flame to a level that only keeps it boiling.
During the cooking process that wraps grease or oil, be careful as this substance can cause
furor if it is at high temperatures.
7. CLEANING AND MAINTENANCE
Before starting cleaning, disconnect the appliance from the power source and allow it to cool.
GENERAL CLEANING
Wash the glazed parts with warm water and detergent: do not use abrasive products as they
may damage it.
Wash the lids of flames and burners often with boiling water and detergent, being careful to
remove all deposits.
The burner holder can be washed in the dishwasher.
For adhering dirt, use normal non-abrasive detergents. We strongly recommend that you do
not use metal, wood or acid scouring pads for cleaning.
BURNER
Clean the burner regularly with a soft cloth, warm water and a little liquid detergent. Do not use
the following products:
• Household detergents or bleaches.
• Scouring soaps Scouring pads are not suitable for non-stick utensils.
• Scourers made of steel wool.
• Stain removers for bathtubs or sinks.
• If the hob is very dirty, use commercial products.
Burner
Minimum diameter
Maximum diameter
Large (fast)
180mm
220mm
Medium (semi - fast)
120mm
200mm
Small (Auxiliary)
80mm
160mm
Triple Flame
220mm
260mm

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
13
IGNITION SPARK PLUG
Automatic burner ignition is provided (when installed) using ceramic plug and metal
electrode. Periodically clean this part of the burner. Also, to avoid difficulties in
ignition, make sure that the cavities in the burner are not clogged.
To remove deposits from the burner cavities, remove the cover and separate
the two parts (see diagram on the right). Once finished cleaning, replace both
parts together and return it to the correct position. After washing, place the pan
support, ensuring that it is correctly in position.
ROUTINE MAINTENANCE
Have the condition and efficiency of the gas line and the pressure regulator
(if installed) periodically checked. If anomalies are detected, do not repair,
but see that the defective part is replaced.
To ensure proper operation and safety, the gas regulator taps should be
periodically greased.
The lubrication of faucets must be periodically and by qualified personnel,
who must always be in contact if the appliance does not work well
.
SERVICE AND PARTS
Before leaving the factory, this equipment was tested and adjusted by the specialized
personnel to give the best operating results. All subsequent repairs or adjustments must be
carried out with the utmost care and attention.
For this reason, we always recommend contacting the distributor who sold the appliance or the
nearest service center, specifying the nature of the problem, the equipment model (Mod.), the
product number (Prod. No.) And the number of series (Ser.No.). These data are on the cover
of this manual.
Always request the use of original spare parts.
WARRANTY CONDITIONS
• Your new appliance is covered by the warranty. The conditions of the guarantee can be seen in the
certificate that you will find inside the product.
• Keep the tax receipt or delivery note, as well as the purchase documents of the product in a safe
place together with the certificate of guarantee.
• If you call the Technical Assistance Service, show these documents to the staff. If you do not follow
these procedures, the facility will have no choice but to charge you for repairs.
• If necessary, you can find in the warranty certificate the nearest service centers.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
14
8. TECHNICAL DATA
Dimensions in mm:
Installation L x P
560 x 480
740 x 480
840 x 480
Type Burner
MAX OUTPUT Kw
MIN OUTPUT kw
Small Auxiliary Burner
1.00
0.35
Semi-fast medium burner
1.75
0.65
Great Quick Burner
3.00
1.0
Triple flame burner
3.80
1.9
G1 / 2 gas connection pipes”
Electricity supply 110v ~ 50 / 60Hz
INSTRUCTIONS FOR THE INSTALLATION TECHNICIAN
CAUTION:
• This appliance should only be installed and used in rooms with permanent ventilation.
• Only qualified personnel should install and connect the appliance to the power source.
• Before any procedure, it is important to check that the appliance is disconnected from the
power source.
• The manufacturer will not be liable for damage caused by improper installation or failure
to comply with accident prevention regulations.

User Manual
BULIT –IN GAS STOVE | LIVORNO 76 Professionale
15
9.PROBLEM SOLVING
• Repairs should only be performed by an authorized technician. Improper repair can be dangerous for
you and other important people.
• However, some minor problems can be solved as follows:
Issue
Probable cause
Solution
It does not turn on
No spark
Check power supply
The burner cover is improperly
mounted
Mount the cover correctly.
The gas supply is closed.
Open the gas supply complete
Poorly lit
The gas supply is not completely open.
Open the supply gas
The burner cover is not properly mounted.
Replace the cover correctly.
The spark plug is contaminated with the foreign
substance.
Clean the foreign substance with a dry cloth.
The burner is wet.
Thoroughly dry burner cap
The holes in the flame diffuser are clogged.
Clean the flame diffuser.
Produces noises when
you turn on
Burner cover is wrong mounted
Mount the burner cap correctly.
Flame shuts off when in
use.
Flame Control has foreign substances.
Clean the device.
The food being cooked overflowed and
extinguished the flame.
Turn off the burner. Wait a minute and turn it
on again.
A strong current turns off the burner.
Turn off the burner and check the kitchen
area, such as open windows. Wait a minute
and turn it on again.
Yellow flame
The holes in the flame diffuser are clogged.
Clean the flame diffuser.
Different gas issued.
Check the gas used.
Unstable flame
The burner cover is not properly mounted.
Mount burner cap correctly
Smell of Gas
Gas leak
Do not use the stop, close the gas valve.
Open the window to ventilate. Contac tour
Service Center from outside.
The problem is not resolved, contact the service center.