Dual Inventive ZKL 3000 RC User manual

Quick Start
ZKL 3000 RC
MTinfo 3000 version 5
February 2020

Before you start!
•ZKL 3000 RC
•Manual and ZKL 3000 RC accessories
•Certificate ZKL 3000 RC
•MTinfo 3000 app
*
Inhoud
1. Function test before you start
2. Installation in the track
3. Operating the MTinfo 3000 app
A Logging in
B Selecting a project
C Switching on
D Switching off
4. Icons, statuses and errors
A Icons
B Statuses
C Errors
1
2
3
4
d
d
*What you will need!

Function test before you start
1
Installation in the track
d
CCheck the status of the ZKL 3000 RC in
the MTinfo 3000 app or on mtinfo3000.com
Install both batteries
A
Place the test tool and install both batteries to
perform the function test.
!
Operate the key switch as follows
B
Make sure the green LED blinks twice per
second during the first two steps!
!
turn it
clockwise
turn it counter-
clockwise

Function test before you start
Installation in the track
2
Operating the MTinfo 3000 app
Place the ZKL 3000 RC in the track
B
Make sure the distance between the underside of
the ZKL 3000 RC and any ballast is at least 30mm.
!
Install the locking clamp
C
Operate the key switch as follows
Place the key switch in the ON position whilst installing
the ZKL and pay attention to the main battery cable.
A
Perform the function test again, see steps 1B
and 1C
D
turn it
clockwise

Installation in the track
Operating the MTinfo 3000 app
3
Selecting a project
B
Logging in
A

Switching on
C
Successfully switched on

Successfully switched on
The green LED will blink
twice per second.
!

Successfully switched off
Switching off
Operating the MTinfo 3000 app
3
D

Successfully switched off
Icons, statuses and errors
Operating the MTinfo 3000 app

Icon Explanation
View the notifications that have been sent by
MTinfo 3000
Refresh the screen
4
Icons, statuses and errors
Icons
A
[ID] [SW] [DET] Explanation
110.0199 ON OK Device has been switched on and
is creating a proper short.
110.0199 ON NOK Device has been switched on and
is NOT creating a proper short.
110.0199 OFF NOK Device has been switched off and is
therefore not creating a proper short.
110.0199 - - Device is not available.
Statuses
B

Icons, statuses and errors
Warning Explanation and solution
ZKL 3000 RC offline
in real-time status
Try again, check the batteries and if
needed use the override key switch.
ZKL 3000 RC battery
is (almost) empty
Replace the battery and try switching
again, also check the battery cable if
required.
Override key is not in
setting OPERATIONAL
ZKL 3000 RC has been overruled with the
override key. It is not possible to remotely
operate this ZKL 3000 RC. Rotate override
key to “OPERATIONAL” to allow remote
switching.
ZKL 3000 RC has been
switched on, but there
is no short circuit
(DET NOK)
ZKL 3000 RC short circuit has not been
detected (DET NOK). Please attempt to
reseat the ZKL 3000 RC in the track and
check again.
Short circuit
already present
When switching, a short circuit was already
detected in the section. The ZKL 3000 RC
cannot guarantee it is creating the short
circuit. Check if the section is clear, and
then try again. Always be sure of a proper
short circuit (in an empty section).
No ZKL 3000 RC
in period / no access
to period
Consult the project lead.
Ensure your own safety when in a railway environment.
Act according to the national regulations.
Alerts
After use, remove all batteries.
Charge before storing the batteries.
!
C

[e-mail]
www.dualinventive.com
And perhaps we'll
see you soon!