Ducati Desmosedici 2008 User manual

2008 Ducati Desmosedici Z-Fi Installation Instructions
P/N F143
WARNING!
USE ONLY IN RACE OR OTHER CLOSED COURSE APPLICATIONS AND NEVER ON PUBLIC ROADS
Z-Fi products do not meet California CARB highway requirements
Parts List:
Z-Fi Control Unit
Mounting Bracket
Fuel Harness
Download Z-Fi Mapper Software & Its Instructions from Website
USB Cable
O2 Eliminators (2)
Scotchlok (2)
Swingarm Stickers
R
Read through all instructions before beginning installation. This is not a replacement for the ECU.
This document is intended for use by qualied technicians. For more specic stock component identition
and location information refer to a factory service manual.
15330 Faireld Ranch Rd., Unit E, Chino Hills, CA 91709 Phone [phone] Fax [phone]
www.Bazzaz.net
To create the ideal map(s) we recommend using the optimal Z-AFM self-tuning module

BAZZAZ HARNESS CONNECTOR IDENTIFICATION
Neutral
Injectors
FUEL HARNESS
Map select
TPS
Ground
Speed
Crank
Power
Z-AFM
1. Remove the following components: Both right & left upper side fairings, fuel tank.

2. Install the supplied control unit mounting bracket to the right side engine cover securing it in place us-
ing the two top cover bolts. Insert the Bazzaz control unit into the bracket. Connect the Bazzaz harness to
the control unit and route the remainder between the frame and front cylinder into the engine compart-
ment (photos 1 & 2).
3. The factory harness crank position and speed sensor connectors can be found secured inside the frame
near the front cylinder head. Disconnect the factory harness connector from the sensor connector and
install the corresponding Bazzaz harness connectors inline (photos 3, 4 & 5).
Photo 1 Photo 2
Speed
Crank
Photo 3
Factory
Bazzaz
Bazzaz Speed Installed
Bazzaz Crank Position
Installed
Bazzaz
Factory
Photo 4 Photo 5

4. Route the portion of the Bazzaz harness containing the power and neutral connectors toward the rear
of the motorcycle along the right side. Locate the factory harness rear brake light switch power supply
connector which can be found near the engine oil ller cap. Disconnect the factory harness connectors
and install the Bazzaz harness power supply connectors in line (photos 6 & 7).
5. Continue to route the neutral sensor lead of the Bazzaz harness (white/blue wire with T-tap) to the
rear of the engine. Locate the factory harness neutral sensor wire (yellow/green) and crimp on a supplied
scotch lok connector onto this wire. Insert the Bazzaz neutral sensor T-tap connector into the scotch lok
and reinstall the factory harness connector onto the sensor at the rear of engine (photos 8 & 9).
Route the remainder of the Bazzaz harness containing the throttle position, injector connectors and
ground between the front and rear cylinders to the left side of the motorcycle.
Factory Brake Light Connector Bazzaz Power Connector Installed
Photo 6 Photo 7
Photo 8 Photo 9

6. Secure the Bazzaz harness ground lug to a chassis ground. Bazzaz recommends using the factory mount-
ing bolt for the radiator mount attached to the left front cylinder head (photo 10).
7. Locate the throttle position sensor and disconnect the factory harness connector. Pull back the harness
sheathing to expose the three wires of the factory harness and crimp on a supplied scotch lok connector
onto the (orange wire). Insert the Bazzaz throttle position sensor T-tap connector (blue wire) into the
scotch lok and reinstall the factory harness connector onto the sensor (photos 11 & 12).
8. Now that the air box has been reinstalled, connect Bazzaz injector connectors in line with the factory
harness connector and the connector located on the left side of the air box (photos 13 & 14).
Bazzaz Ground Lug Installed Photo 10
Photo 12
Photo 11
Bazzaz TPS (Blue) onto Factory Orange

9. Reinstall the components removed in step one of these instructions.
The Bazzaz controller is capable of storing two maps. These maps can be selected through the use of a
map select switch which can be mounted on the handlebar for easy access and can be purchased seper-
ately. Or these maps can be selected by connecting or disconnecting the map select jumper supplied with
the kit. When the map selet jumper is connected the control unit is operating using map 1. When the
map select jumper is disconnected the contol unit is operating using map 2.
Factory Injector Connector Bazzaz Connectors
Map 1 Map 2
Photo 13 Photo 14
Factory Connector