Duplo DSC-10/60i User manual

INSTRUCTION MANUAL
COLLATOR
DSC-10/60i
Be sure to read this manual prior to use.
Please leave this manual at the site of use for easy reference.

Introduction
Thank you for purchasing a Duplo product.
Be sure to read this manual prior to using the product.
After reading, leave the manual at the site of use for easy reference whenever questions related to the
product arise in the future.
Symbols
In this manual, several symbols are used to indicate important warnings. Please make sure to read
instructions accompanied by these symbols. These symbols have the following
meanings.
Describes instructions which must be followed in use.
Be sure to read the instructions to avoid problems due to incorrect operations.
Indicates supplementary or useful information.
Describes names of related items and supplementary instructions.
Trademark
The product name and company name used in this manual are trademarks or registered trademarks of the
respective companies.

DECLARATION OF CONFORMITY
Duplo Corporation, located at 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japan, declares that the product (or products)
complies with the provisions dened in the regulations. The reference table is mentioned below.
Name of product Model
Regulation
Machinery Directive
2006/42/EC under
Low Voltage Directive
2006/95/ECunder
Electromagnetic Compatibility
Directive 2004/108/EC under
Collator DSC-10/60 EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 + A1: 2009
including EN60950-1: 2006 +
A11: 2009 + A1: 2010 + A12: 2011
deviations
EN61000-3-2: 2006 + A1: 2009 + A2: 2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007 + A1: 2011
Keeper of the technical le in the European Community:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
En
KONFORMITÄTSERKLÄRUNG
Die Duplo Corporation mit Sitz in 1-6, Oyama 4 chome, Chuo-ku, Sagamihara, Kanagawa 252-5280 Japan, erklärt hiermit, dass das Produkt (oder die
Produkte) die in den Vorschriften denierten Bestimmungen erfüllt. Die Bezugstabelle ist unten aufgeführt.
Bezeichnung des
Produkts Modell
Richtlinie
Maschinenrichtlinie
2006/42 EG unter
Niederspannungsrichtlinie
2006/95/EG unter
Richtlinie zur elektromagnetischen
Verträglichkeit 2004/108/EG unter
Zusammentragmaschine DSC-10/60 EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 + A1: 2009
including EN60950-1: 2006 +
A11: 2009 + A1: 2010 + A12: 2011
deviations
EN61000-3-2: 2006 + A1: 2009 + A2: 2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007 + A1: 2011
Inhaber der technischen Datei in der Europäischen Gemeinschaft:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Ge
DECLARATION DE CONFORMITE
Duplo Corporation, dont le siège est situé au 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japon, déclare que le ou les produits
sont conformes aux dispositions dénies par la réglementation. Un tableau de référence est proposé ci-dessous.
Nom du produit Modèle
Réglementation
Directive Machines
2006/42/CE en application
de la
Directive Basse tension
2006/95/CE en application
de la
Directive sur la compatibilité
électromagnétique 2004/108/CE
en application de
Assembleuse DSC-10/60 EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 + A1: 2009
including EN60950-1: 2006 +
A11: 2009 + A1: 2010 + A12: 2011
deviations
EN61000-3-2: 2006 + A1: 2009 + A2: 2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007 + A1: 2011
Conservateur du dossier technique dans la Communauté Européenne :
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Fr
DICHIARAZIONE DI CONFORMITÁ
Duplo Corporation, sita a 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Giappone, dichiara che il prodotto (o i prodotti) è/sono
conforme/i ai requisiti deniti dalle norme sottoelencate. La tabella di riferimento è riportata qui di seguito.
Nome del prodotto Modello
Direttiva Bassa Tensione
Direttiva sui macchinari
2006/42/CE in base a
Direttiva 2006/95/CE relativa
alle apparecchiature a bassa
tensione
Direttiva di compatibilità
elettromagnetica 2004/108/CE
in base a
Fascicolatore DSC-10/60 EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 + A1: 2009
including EN60950-1: 2006 +
A11: 2009 + A1: 2010 + A12: 2011
deviations
EN61000-3-2: 2006 + A1: 2009 + A2: 2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007 + A1: 2011
Responsabile della documentazione tecnica all’interno della Comunità Europea:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
It
DECLARACIÓN DE CONFORMIDAD
Duplo Corporation, con domicilio en 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japón, declara que el producto (o los
productos) cumple con las disposiciones previstas en los reglamentos. Seguidamente se indica la tabla de referencia.
Nombre del producto Modelos
Reglamentación - Reglamentaciones
Directiva sobre máquinas
2006/42/CE, según
Directiva sobre baja tensión
2006/95/CE, según
Directiva sobre compatibilidad
electromagnética 2004/108/CE,
según
Clasicador DSC-10/60 EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 + A1: 2009
including EN60950-1: 2006 +
A11: 2009 + A1: 2010 + A12: 2011
deviations
EN61000-3-2: 2006 + A1: 2009 + A2: 2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007 + A1: 2011
Depositario del archivo técnico en la Comunidad Europea:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Sp
For EU

DECLARATION OF INCORPORATION
Duplo Corporation, located at 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japan, declares:
• the essential requirements of the Machinery Directive are applied to the product (or products) mentioned in the table below and;
• the product (or products) complies with the provisions dened in the regulations mentioned in the table below and;
• the technical documentation is compiled in accordance with the Machinery Directive Annex VII part B;
and undertakes:
• to transmit relevant information of the product (or products) by appropriate method in response to reasoned request by the national authorities.
However that transmission shall be without prejudice to our intellectual property rights of the product (or products);
and states:
• the product (or products) is partly completed machinery and must not be put into service until the nal machinery into which it is to be
incorporated has been declared in conformity with the provisions of the Machinery Directive.
Name of product Model
Regulation
Machinery Directive
2006/42/EC under
Low Voltage Directive
2006/95/EC under
Electromagnetic Compatibility
Directive 2004/108/EC under
Collator Accessories PC CONTROLLER
(IF board, PC bracket)
EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 including
EN60950-1: 2006 + A11: 2009
deviations
EN61000-3-2: 2006 + A1: 2009 + A2:
2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007
D-PORT CONVERTER
LUL-HM
BRIDGE
ULTRASONIC SENSOR KIT
Keeper of the technical le in the European Community:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
En
ERKLÄRUNG DER AMTLICHEN EINTRAGUNG
Die Duplo Corporation mit Sitz in 1-6, Oyama 4 chome, Chuo-ku, Sagamihara, Kanagawa 252-5280 Japan, erklärt hiermit:
• alle wesentlichen Erfordernisse der Maschinenrichtlinie sind auf das in der untenstehenden Tabelle genannte Produkt (oder die Produkte)
angewendet worden, und
• das Produkt (oder die Produkte) erfüllt die Bestimmungen, die in den in der untenstehenden Tabelle genannten Vorschriften deniert sind, und
• die technische Dokumentation ist entsprechend der Maschinenrichtlinie Anhang VII Teil B zusammengestellt;
und verpichtet sich:
• auf begründete Anfragen der nationalen Behörden sachdienliche Informationen über das Produkt (die Produkte) mittels einer geeigneten
Methode zu liefern. Die Übergabe erfolgt jedoch so, dass unsere geistigen Eigentumsrechte am Produkt (oder den Produkten) nicht
beeinträchtigt werden,
und erklärt:
• das Produkt (oder die Produkte) ist ein Teil einer nicht vollständigen Maschinenanlage und darf so lange nicht in Betrieb genommen werden, bis
die komplette Maschinenanlage, in die es eingebaut wurde, oziell als mit der Maschinenrichtlinie übereinstimmend erklärt worden ist.
Bezeichnung des Produkt Modell
Richtlinie
Maschinenrichtlinie
2006/42 EG unter
Niederspannungsrichtlinie
2006/95/EG unter
Richtlinie zur elektromagnetischen
Verträglichkeit 2004/108/EG unter
Zubehör der
Zusammentragmaschine
PC CONTROLLER
(IF board, PC bracket
EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005 einschließlich
Abweichungen der
EN60950-1: 2006 + A11: 2009
EN61000-3-2: 2006 + A1: 2009 + A2:
2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007
D-PORT CONVERTER
LUL-HM
BRIDGE
ULTRASONIC SENSOR KIT
Inhaber der technischen Datei in der Europäischen Gemeinschaft:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Ge
DECLARATION D’INTEGRATION
Duplo Corporation, dont le siège social est situé au 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japon, déclare :
• que les exigences essentielles de la Directive Machines sont appliquées au(x) produit(s) mentionné(s) dans le tableau ci-après,
• que le produit ou les produits sont conformes aux dispositions dénies par la réglementation mentionnée dans le tableau ci-après, et
• que la documentation technique a été réalisée conformément à l’Annexe VII partie B de la Directive Machines,
s’engage :
• à communiquer des informations pertinentes sur le ou les produits par un mode de transmission adapté en réponse à toute demande motivée
des autorités nationales. Toutefois, la communication de ces informations sera sans préjudice de nos droits de propriété intellectuelle en ce qui
concerne le ou les produits ;
et précise :
• que le ou les produits sont des machines en partie achevées et qu’ils ne doivent pas être mis en service avant que la machine dénitive dans
laquelle ils doivent être intégrés ait été déclarée conforme aux dispositions de la Directive Machine.
Nom du produit Modèle
Réglementation
Directive Machines
2006/42/CE en application
de la
Directive Basse tension
2006/95/CE en application
de la
Directive sur la compatibilité
électromagnétique 2004/108/CE en
application de
Accessoires de la relieuse PC CONTROLLER
(IF board, PC bracket)
EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC 60950-1: 2005, dérogations
selon
EN60950-1: 2006 + A11: 2009
incluses
EN61000-3-2: 2006 + A1: 2009 + A2:
2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007
D-PORT CONVERTER
LUL-HM
BRIDGE
ULTRASONIC SENSOR KIT
Conservateur du dossier technique dans la Communauté Européenne :
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Fr
For EU

DICHIARAZIONE DI ISCRIZIONE
Duplo Corporation, sita a 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Giappone, dichiara che:
• i requisiti fondamentali della Direttiva sui macchinari sono applicati al prodotto (o prodotti) menzionato/i nella seguente tabella e
• il prodotto (o prodotti) è/sono conforme/i ai requisiti deniti nelle norme sottoelencate e;
• la documentazione tecnica è stata compilata conformemente alla Direttiva sui Macchinari Appendice VII parte B;
e si impegna a:
• trasmettere informazioni inerenti al prodotto (o sui prodotti) con un metodo appropriato in risposta a una richiesta logica da parte delle autorità
nazionali. La trasmissione di tali informazioni non deve comunque ledere i nostri diritti di proprietà intellettuale sul prodotto (o sui prodotti);
e specica che:
• il prodotto (o i prodotti) è/sono incompleto e non deve essere messo in funzione nché il macchinario nale in cui deve essere incorporato non
sia stato dichiarato conforme ai requisiti dichiarati dalla Direttiva sui Macchinari.
Nome del prodotto Modello
Direttiva Bassa Tensione
Direttiva sui macchinari
2006/42/CE in base a
Direttiva 2006/95/CE relativa
alle apparecchiature a bassa
tensione
Direttiva di compatibilità
elettromagnetica 2004/108/CE
in base a
Accessori del fascicolatore PC CONTROLLER
(IF board, PC bracket)
EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC 60950-1: 2005 deviazioni
EN 60950-1: 2006 + A11: 2009
incluse
EN61000-3-2: 2006 + A1: 2009 + A2:
2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007
D-PORT CONVERTER
LUL-HM
BRIDGE
ULTRASONIC SENSOR KIT
Responsabile della documentazione tecnica all’interno della Comunità Europea:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
It
DECLARACIÓN DE INCORPORACIÓN DEL PRODUCTO (O LOS PRODUCTOS)
Duplo Corporation, con domicilio en 1-6, Oyama 4-chome, Chuo-ku, Sagamihara, Kanagawa 252-5280, Japón, declara que:
• el producto (o los productos) indicado en la siguiente tabla cumple con los requisitos esenciales de la Directiva sobre máquinas; y que
• el producto (o los productos) cumple con las disposiciones previstas en los reglamentos indicados en la siguiente tabla; y que
• la documentación técnica se ha recabado de conformidad con la Directiva sobre máquinas, anexo VII, parte B;
y se compromete a:
• comunicar información relevante sobre el producto (o los productos) por el método apropiado como respuesta a la solicitud debidamente
formulada por las autoridades nacionales. No obstante, dicha comunicación se efectuará sin perjuicio de nuestros derechos de propiedad
intelectual sobre el producto (o los productos);
y declara que:
• el producto (o los productos) es un aparato parcialmente terminado, por lo que el mismo no se deberá poner en funcionamiento hasta que se
haya declarado que el aparato nal en el que será incorporado cumple con las disposiciones previstas en la Directiva sobre máquinas.
Nombre del producto Modelos
Reglamentación - Reglamentaciones
Directiva sobre máquinas
2006/42/CE, según Directiva sobre baja tensión
2006/95/CE, según
Directiva sobre compatibilidad
electromagnética 2004/108/CE,
según
Accesorios del clasicador PC CONTROLLER
(IF board, PC bracket)
EN1010-1: 2004 + A1: 2010
EN1010-4: 2004 + A1: 2009
EN60204-1: 2006 + A1: 2009
IEC60950-1: 2005, incluyendo
EN60950-1: 2006 + A11: 2009
modicadas.
EN61000-3-2: 2006 + A1: 2009 + A2:
2009
EN61000-3-3: 2008
EN61000-6-2: 2005
EN61000-6-4: 2007
D-PORT CONVERTER
LUL-HM
BRIDGE
ULTRASONIC SENSOR KIT
Depositario del archivo técnico en la Comunidad Europea:
Duplo International Ltd, Automated Precision House, Hamm Moor Lane, Addlestone, Surrey, KT15 2SD, United Kingdom
Sp

For EU
Disposal of Old Electrical & Electronic Equipment
This symbol (the symbol of the crossed out wheeled
bin) indicates that in European countries this product
should not be disposed of as household waste.
Please recycle where facilities exist by checking with
your local authority or supplier for recycling advice.
By ensuring this product is disposed of correctly
through proper treatment, recovery and recycling,
you will help prevent potential negative eects on the
environment and human health.
En
Entsorgung von alten elektrischen und
elektronischen Ausrüstungsteilen
Dieses Symbol (das Symbol mit dem durchgekreuzten
fahrbaren Müllbehälter) zeigt an, dass dieses Produkt
in europäischen Länden nicht als Haushaltsmüll
entsorgt werden darf. Bitte informieren Sie sich bei
Ihren örtlichen Behörden oder bei Ihrem Händler
hinsichtlich einer Empfehlung für die Entsorgung
und führen Sie die betreenden Teile dort, wo solche
Einrichtungen vorhanden sind, einem Recycling-
Prozess zu.
Indem sie sicherstellen, dass das betreende Produkt
durch richtige Behandlung, Rückführung und Recycling
entsorgt wird, tragen Sie dazu bei, möglichen negativen
Auswirkungen auf die Umwelt und die menschliche
Gesundheit vorzubeugen.
Ge
Elimination du matériel électronique et électrique
usagé
Ce symbole (une poubelle marquée d’une croix)
indique que dans les pays européens, ce produit ne
doit pas être éliminé comme des ordures ménagères.
Recyclez-le dans les sites adaptés qui vous seront
indiqués par les autorités locales ou renseignez-vous
auprès de votre fournisseur.
En veillant à ce que ce produit soit éliminé
correctement avec un traitement, une collecte et un
recyclage adaptés, vous contribuez à éviter son action
nocive potentielle sur l’ environnement et la santé
humaine.
Fr
Smaltimento di attrezzature elettriche ed
elettroniche consumate
Questo simbolo (il simbolo della pattumiera con rotelle
barrata) indica che nei paesi europei questo prodotto
non deve essere buttato nei rifiuti domestici.
Per favore smaltire in luogo addetto al riciclo, dove
esistente, chiedendo informazioni alle autorità locali o
a chi fornisce consulenza a proposito.
Garantendo uno smaltimento adeguato di questo
prodotto (trattamento, recupero e riciclo corretto),
aiuterete a prevenire eetti negativi sull’ambiente e
sulla salute dell’uomo.
It
Eliminación de residuos de aparatos eléctricos y
electrónicos
Este símbolo (un cubo de basura tachado) indica
que en los países europeos este producto no deberá
eliminarse como si se tratara de un residuo doméstico.
Solicite asesoramiento sobre reciclaje a las autoridades
locales o a su distribuidor, y siga la normativa en
materia de gestión medioambiental y reciclaje de este
tipo de residuos.
Si toma las medidas pertinentes para que este
producto se elimine mediante un tratamiento,
recuperación y reciclaje adecuados, contribuirá a evitar
posibles efectos negativos en el medio ambiente y la
salud humana.
Sp
For North America
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

i
Safety Precautions
Safety Precautions
In this manual, operations and handling of the unit which are hazardous are described using the following
marks to prevent personal injury or property damage to the user and others.
Ignoring this mark could result in the possibility of
serious injury or even death.
Ignoring this mark could result in the possibility of injury
or physical damage.
This mark indicates a “Warning” or “Caution”.
A graphic may be shown inside the mark to describe the warning or caution more specically.
This mark indicates a forbidden action.
A graphic may be shown inside the mark to describe the forbidden action more specically.
This mark indicates actions that must be performed.
A graphic may be shown inside the mark to describe the action to be performed more specically.
Power Supply
• Make sure the power supply used is always within the following range.
Power supply : 120 V AC, 60 Hz (North America)
220 to 240 V AC, 50/60 Hz (EU)
• When you power other appliances from the same AC outlet, make sure that the combined power
consumption does not exceed the power supply capacity.
Rated current, Rated power : 8.4 A, 960 W (Excl. D-PORT CONVERTER 7.9 A, 910 W)(North America)
5.3 A, 980 W (Excl. D-PORT CONVERTER 5.1 A, 930 W) (EU)
Use only the power supply voltage specied on the main nameplate.
Using other voltages could result in a re or an electrical shock.
Make sure that the combined power consumption of the appliances to be
connected does not exceed the capacity rating of the power outlets or plug
receptacles.
Exceeding the capacity rating could cause the power outlets, plug receptacles, or power extension cords to
overheat and catch a re.

ii
Safety Precautions
Operating Environment
Operate this unit in the following environment.
• where the temperature range is between 5 and 35°C (-10 to +50°C in storage)
• where the humidity range is between 20 and 85% RH (10 to 90% RH in storage, however no condensation)
• which is not subject to direct sunlight
• which is reasonably free from dust
• which is subject to little or no vibration
• which is free from air-borne salt
• where there are no harmful chemicals
• where the unit is not exposed to water
Keep this unit and the power cord away from heaters and heater vents.
Excessive heat could melt the cover or power cord covering, and result in a re or an electrical shock.
Do not place metal objects or vessels containing liquids on top of the unit.
The entry of any metal object or liquid could result in a re or an electrical shock.
Do not insert any metal or easily-combustible object inside this unit.
This could result in a re or an electrical shock.
Do not use ammable sprays inside or near the unit (e.g. when cleaning the
unit).
Such ammable gas may ignite and cause a re or combustion.
Do not install this unit in a location where there is excessive humidity or
where contact with water is possible.
Poor choice of location could result in deterioration of the insulation, a re or an electrical shock.
Install this unit on a level, stable stand or oor, with sucient space around it.
Failure to do so could result in the unit overturning and causing injury.
Disconnect the power plug from the power outlet before attempting to move
this unit.
Failure to do so could result in power cord damage, a re or an electrical shock.
Always disconnect the power plug from the power outlet when the unit is not
to be used for an extended period.
Failure to do so could result in a re due to leakage current if the insulation should deteriorate.

iii
Safety Precautions
Maintenance / Other
Do not damage the power cord or power plug.
Do not scratch, alter, bend, twist, pull or place heavy objects on the power cord or power plug.
This could result in damage, a re or an electrical shock.
Do not touch the power switch with wet hands.
Otherwise electric hazards may occur.
Do not remove the cover or back panel.
This unit contains high-voltage components that could cause an electrical shock.
Do not disassemble, modify or repair this unit.
There is a danger of re, electrical shock or injury.
Contact your dealer when repairs are necessary.
If any foreign object such as metal or liquid should enter this unit,
immediately turn the unit o at the power switch and disconnect the power
plug from the power outlet.
Failure to do so could result in a re or an electrical shock.
Contact your dealer immediately.
Before cleaning this unit, turn the unit o at the power switch and disconnect
the power plug from the power outlet.
Accidental operation of the unit during cleaning could result in injury.
Remove any dust that accumulates on the power plug prongs and the surface
of the plug from which the prongs extend.
Accumulated dust could result in a re.
Always grip the plug when disconnecting the power plug from the power
outlet.
Forcibly pulling on the power cord could cause damage, resulting in a re or an electrical shock.
Do not touch or insert foreign objects into any rotating part during operation.
This could result in injury.

iv
Safety Precautions
WARNING / CAUTION Labels
"WARNING" and "CAUTION" labels are pasted on the machine to ensure user safety.
Do not remove or change them.
When the labels become dirty or are lost, be sure to contact your dealer for a new one.
For EU