Durovin Bathrooms Ravenna 17-2 DR04 User manual

Ravenna 17-2nd
Door Only
Installation Manual

02 05 06
10 11
*4
*4
03 04
08 09
*6
01
07
C015A*2
DR04 partition accessories packaging
12
*6
13 14
S06*1 M307AB*2
DR04 Waterproof strip
packing
304AAK*1
15
DR04 rail packaging
19
D003*1
18
D017*1
16 17
*1 *1
DR04 door glass packaging
1018*1 Ø48Wheels*2 Square wall
sleeve*2 Anti-jump nail*2 Square tube
fastener*2
H003*1

19
14
13
18
8
3
25
12
16
INSTALLATION ACCESSORIES LIST
Tools for installation
ABCDEF
10
9
16
17
15
7
11
4
1
NAME
NO. UNIT
QTY
2
3
7
13
14
QTY UNITNO. NAME QTY
NO. NAME UNIT
4
8
9
10
15
5
6
11
12
16
17
18
19 1PCS
1
1
1
2
2
6
6
21
1
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
lead rail
Fixed glass
Activity of
glass
The water bar
aluminum alloy
Moving glass
The wall of
M8 expansion pipe
ST5*40
The big wheel
2PCS
Guide rail and fixed
glass fittings
1PC
Fixed glass bar
1PC
Door glass guide
block A
2PCS
Unilateral
Angle code
fixed glass
4PCS
ST4*40
4PCS
M6 expansion
pipe
1PCS
handle
2PCS
Defend jump
wheel
Door glass guide
block B

2
Step 1: get the wall water bar to the fixed glass, and the Angle
code is installed and tightened, as shown in the figure:
∅8
Step2: move the fixed glass to the installation position, then
open the hole on the wall, and fix the fixed glass to the wall
with plastic capsules and self-tapping nails, as shown in the
figure:
B
D
C
15
17
7
8
12

Step4: take down guide first, and then take the plug core out (with a
hexagonal wrench open), pen make hole mark on the wall, and then open
hole and into the plastic expansion tubes, and the guide rail with
self tapping screw plug core is fixed to the wall, as shown in
figure:
3
∅8∅8
Step3: put the guide rail onto the glass, and use the horizontal ruler
(as shown in the picture), then mark the wall with a marker pen, as
shown in the figure.
36
6
19
8
12
8
12

4
Step 5: connect the guide rail to the wall first, then connect
with the glass and tighten, then tighten the ends of the rails;
Step6: first put the water bar into the movable glass (the
front and back are not wrong), and then put the pulley on the
door of the activity (not too tight), as shown in the figure:
12MM
13
14
16
2

Step 8: pull the handle and pull the door to the wall to
determine the location of the guide block:
5
1
15
Step7: the first guide block (note the left and right) fixed to the floor (if it
is at the bottom of basin ∅ 3 holes directly, without plastic expansion tubes),
then the door on a guide rail, as shown in figure:
∅6
4
11
9
10

Step10: use a small wrench to adjust pulley (pulley as eccentric, with a small
wrench around adjustment can make the door up activities, adjust good after the
lock nut), make the door and wall gap is consistent and tighten up and down, and
then loaded on the wheel and weather bar, OK.
24H
6
Step9: the guide block and weather bar (aluminum) fixed to the floor (if it is at
the bottom of basin, directly open ∅ 3 holes, no plug expansion pipe), as shown in
figure:
∅6
11
4
10
5