Dwyer Instruments BPI Series Installation and operating instructions

Series BPI/R D Battery Powered emperature Indicator
Specifications - Installation and Operating Instructions
Bulletin E-90-BPI/R D
DWYER INS RUMEN S, INC. Phone: [phone] www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CI Y, INDIANA 46361, U.S.A. Fax: [phone] e-mail: [e-mail]
The S ri s BPI is a range of battery powered temperature
indicators. The Series B I-XX1 accepts an RTD sensor; the
Series B I-XX2 accepts a thermocouple sensor. The sensor
type, temperature units and other flexible configuration settings
are selectable via a simple to use menu system, which is
navigated by the use of three push-button keys located on the
rear of the display. The entire assembly is sealed into a cap that
fits directly onto the connecting heads.
lease inspect the packaging and instrument thoroughly for any
signs of transit damage. If the instrument has been damaged,
please notify your shipper immediately.
INSTALLATION
Configuration - Fit the battery as described in Battery section,
then follow the simple configuration menus printed on the
reverse side of this sheet. This procedure can be performed with
or without the sensor connected. Fit the correct units legend to
the front panel face.
Enclosur - The case offers various options for sensor entry.
lease refer to the data sheet for further details. The sensor
may be fixed directly to the housing, or remotely connected
using cable and gland. Cable length must be no greater than 20
meters to comply with CE certification. All external
cabling/sensor entries must maintain I 67 rating.
Wiring
BPI/RTD Conn ction
SPECIFICATION @ 68°F (20°C)
Inputs: Thermocouple or RTD depending on model.
Accuracy: Thermocouple input: ±0.1% FS, ±0.5°C
(plus sensor); RTD: ±0.2°C ±0.1% of reading (plus sensor error).
Pow r R quir m nts: 3.6 V Lithium battery.
Batt ry Lif : >2 years.
Display: 4-digit LCD.
R solution: 0.1°C.
Ambi nt Op rating T mp ratur : 14 to 158°F (-10 to 70°C).
Storag T mp ratur : -4 to 185°F (-20 to 85°C).
W ight: 6.0 oz (170 g).
Front Pan l Prot ction: NEMA 4X (I 65).
Ag ncy Approval: CE.
Batt ry
To install battery, first gain access to the battery by unscrewing
the cap retaining nut and removing cap from base. To remove
old battery, ease out the positive end of the battery from the
holder, using a screw driver blade. To fit battery, insert battery
negative into the spring contact end of the battery holder, then
press battery into place.
The units monitor their batteries. When the battery approaches
the end of its lifetime (over 2 years under normal conditions), the
display will toggle the message “LO BAT”.
lease observe the battery warning.
Ensure the instrument is installed with adequate protection
against the environment. I 67 rating must be maintained.
Try to avoid installing the equipment close to sources of extreme
temperature and electrical or electromagnetic interference.
Any cleaning of the instrument should be carried out using a mild
detergent and a soft cloth. No solvents or abrasive cleaner
should be used.
+
BH1
DEC
INC CYC
RTD
Connection
13/16
[20.7]
13/64
[5]
Ø2-5/8
[Ø66.7]
Ø2-7/8
[Ø73]
Fire, Explosion and severe burn hazard, DO NOT
Recharge, Crush, Disassemble, Heat above
100°C (212°F), Incinerate or expose contents to water. NEVER
short circuit the battery. Disposal, the battery may be regulated
by national and local regulations. lease follow the instructions
of the proper regulator.
WARNING

There are three buttons, which the operator must
press in various combinations in order to configure
the device. These buttons are located on the
underside of the indicator’s circuit board. Viewed
from the front, the three buttons (CYCle ,
INCrement and DECrement
) are shown in the diagram
to the left. ressing 2 buttons
simultaneously causes ENTer
or ESCape actions.
©Copy ight 2011 Dwye Inst uments, Inc. P inted in U.S.A. 4/11 FR# R5-443914-00
DWYER INS RUMEN S, INC. Phone: [phone] www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CI Y, INDIANA 46361, U.S.A. Fax: [phone] e-mail: [e-mail]
MAINTENANCE
Apart from battery replacement this equipment requires no user
maintenance. If re-calibration is required please contact your
supplier for further information. Under certain circumstances, it
may be possible to re-calibrate the device while it is still out in an
application.
SERIES BPI/RTD CONFIGURATION MENU GUIDE
Run-Time
then
INC
DEC
CYC
If no buttons are pressed for a minute or more, the
device assumes run-time mode. The display shows
the V (if the input is in range) or shows or
to indicate over/under range. In order to access
menu configuration mode, the user must press
ENTer followed immediately by CYCle . In
order to exit the menu and return to run-time, a user
must press ESCape .
CYCle around menu
When cycling around menu, the
title (e.g. TY E, UNIT, etc.) is
displayed for a second, then the
menu entry is displayed ready for
editing. Then use INC/DEC to
move through entries in a list, or
to edit a real number.
INCrement menu entry
DECrement menu entry
ENTer to confirm entry, or:
CYCle to next menu entry
ESCape
The Series B I Battery owered Temperature Indicator is not
field serviceable and should be returned if repair is needed (field
repair should not be attempted and may void warranty). Be sure
to include a brief description of the problem plus any relevant
application notes. Contact customer service to receive a return
goods authorization number before shipping.