Dynacraft 24V TRAIL RACER User manual

this manual contains important safety, performance and
maintenance information. read the manual before taking your
first ride or allowing your child to ride your new electric
ride-on toy. keep the manual handy for future reference.
24V TRAIL RACER
OWNER’S MANUAL
FOR AGES 3+
MAXIMUM WEIGHT: TOTAL 130 lb (59 kg), 65 lb (29.5 kg) per seat
DO NOT RETURN THIS ITEM TO THE STORE
CONTACT DYNACRAFT CUSTOMER SERVICE FOR ASSISTANCE
dynacraftwheels.com/contact
or 1-800-551-0032
NOTE: Illustrations in this Manual are for reference purposes only and may not reflect the
exact appearance of the actual product. Specifications are subject to change without notice.

1
A Introduction, Safety and Warnings 2
B Before You Begin Assembly 6
C Parts Diagram 7
D Assembly 8
E How to Use Your Ride-On Toy 17
F Detailed Maintenance and Repair 20
G Troubleshooting Guide 26
H Limited Warranty 29
SUITABLE AGE 3+
CAPACITY Up to 130 lb (59 kg)
MAX SPEED Low 2 5 MPH / High 5 0 MPH
CHARGER / INPUT AC120V / 60HZ
OUTPUT DC 24V / 1A
CHARGING 12-18 Hours
BATTERY 24V 7AH, 1x Battery
SIZE 133 x 87 x 115 cm
AVERAGE BATTERY LIFE 300 Charges
This is an estimate only, not a guarantee. Actual battery performance will vary based on many
factors, including but not limited to maintenance, charging habits, operation of product, and
temperature.
TABLE OF CONTENTS
SPECIFICATIONS

2
INTRODUCTION, SAFETY AND WARNINGS A
ABOUT THIS MANUAL: This Manual was written to help you and your child get
the most performance, comfort, enjoyment and safety when riding your new
electric ride-on toy. It is important for you to understand your new electric ride-on
toy. By reading this manual before you let your child go out on his/her first ride,
you will know how to get the most from your new electric ride-on toy. It is also
important that you or your child’s first ride be in a controlled environment, away
from cars, obstacles, and other riders.
GENERAL WARNING: Riding an electric ride-on toy can be a dangerous
activity, even under the best of circumstances. Proper maintenance of your new ride-on toy is
your responsibility and helps reduce the risk of injury. Certain conditions may cause components
to fail without fault of the manufacturer. The ride-on toy can and is intended to move, and it is
therefore possible to lose control, fall off and/or get into dangerous situations that no amount of
care, instruction or expertise can eliminate. If such a thing does occur, your child can become
seriously injured or die, even when using safety equipment and other safety precautions.
WARNING: To reduce risk of injury, adult supervision is required. Never use in
roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other
bodies of water; always wear shoes, and never allow more than two (2) riders.
WARNING: CHOKING HAZARD–Small parts not suitable for children under 3 years old.
WARNING: This toy is unsuitable for children under 3 years due to its maximum speed.
WARNING: This toy should be used with caution since skill is required to avoid
falls or collisions causing injury to the user or third parties. Parents must make sure that
children can operate the ride-on toy safely before letting them ride it.
WARNING: Do not ride in rain, snow, or mud, or store the ride-on toy outside without
covering. Water can damage components, including the motor, electrical system, and battery.
WARNING: This ride-on toy is not an off-road vehicle and is intended to be ridden
on smooth, level ground. Do not ride in loose dirt, sand, or gravel, which could damage
moving parts, the motor, or the electrical system.
NOTE: Store the ride-on toy indoors or in a covered location when not in use. Avoid long
term exposure to rain, excessive sun, or other inclement weather.
RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE. This manual
contains many warnings and cautions concerning the consequences of failing to inspect,
maintain or properly use your electric ride-on toy. Because any fall can result in serious
injury or even death, we do not repeat the warning of possible serious injury or death each
time such a possibility is mentioned in this manual or the risk of falling leads to a warning.
ALWAYS USE PROPER RIDING ATTIRE. Always wear appropriate clothing and shoes.
Never ride barefoot or in sandals and make sure that shoelaces or other fasteners are tied
and kept away from the wheels and drive system of the ride-on toy.

3
RIDER USE AND REQUIRED PARENTAL SUPERVISION
RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 130 LB (59 KG) AND
MUST BE OVER 3 YEARS OLD. NEVER ALLOW MORE THAN 2 CHILDREN TO
RIDE THE RIDE-ON TOY SIMULTANEOUSLY.
The age grade for the electric ride-on toy is for 3 years and older. Just because
your child is within the age and weight limitations specified for the electric ride-
on toy, does not mean that his/her size is appropriate to fit or maintain control of
the electric ride-on toy, or that he/she is capable of safely operating the electric
ride-on toy. You are the best judge of whether you or your child can safely operate
the electric ride-on toy; this includes determining whether your child is at the
appropriate developmental stage for safe use of the electric ride-on toy. Any rider
that is unable to fit comfortably on the electric ride-on toy should never attempt to
ride it. A parent's decision to allow their child to use the electric ride-on toy should
be based on the child's maturity, skill and their ability to follow rules. Remember
that the electric ride-on toy is intended for use only by children who are, at a
minimum, able to comfortably and safely operate it.
Children operating the electric ride-on toy should be supervised by an adult at all
times. Parents should ensure that children only use the electric ride-on toy safely
and within their age and physical limits.
This manual contains very important safety information. It is your responsibility to
completely review this information and make sure that all riders understand all of
the warnings, cautions, instructions and safety topics addressed in this manual
and to assure that all riders are able to safely and responsibly use the electric
ride-on toy. You should periodically review and reinforce all information in this
manual with all riders, especially children. You should also regularly inspect and
maintain your electric ride-on toy to ensure the safety of all riders. Make sure that
your new electric ride-on toy is properly fitted to any child riding it; that it is in good
repair and safe operating condition; that you and your child have gone over the
use, operation and safety information in this manual; that you and your child have
learned and understand what to do and what not to do with your new electric ride-
on toy, including observing all applicable laws, rules and common sense.
Children should be made aware of all possible riding hazards and correct riding
behavior before they ride the electric ride-on toy and should be supervised by an
adult at all times. Please explain the following to them as often as necessary.

4
SAFE RIDING PRACTICES AND WARNINGS
• Check and obey all local laws or regulations which may be in effect in the
locations where the electric ride-on toy may be used.
• Always wear appropriate clothing and shoes.
• Observe the age and weight limitations on the cover of this manual.
• Always stay seated while riding the electric ride-on toy. To stop you must take
your foot off the foot pedal.
• Children must be supervised by an adult at all times to be safe.
• Always be alert and ride your electric ride-on toy defensively. Watch out for
obstacles that could catch one of the electric ride-on toy's wheels or force you
to turn suddenly and/or lose control. Be careful to avoid pedestrians, persons
using other wheeled products (including roller or in-line skates, skateboards,
scooters, bikes, etc.), children or animals who may enter your path. Always
respect the rights and property of others.
• Do not activate the foot pedal unless you are seated in the ride-on toy and in a
safe, outdoor environment that is suitable for riding your electric ride-on toy.
• Do not attempt or perform any stunts or tricks on the electric ride-on toy. It is
not made to withstand such misuse and abuse.
• Keep both hands on the steering wheel at all times.
• Do not touch the motor on the electric ride-on toy when in use or directly after
use as these parts can become extremely hot.
• Never allow more than one child to ride the electric ride-on toy at one time and
never try to tow anything.
• Do not use near steps, water, or swimming pools.
• Do not ride in wet weather.
• Never immerse the electric ride-on toy in water; electrical and drive components
could be damaged by water or create other potentially unsafe conditions.
• Keep your fingers and other body parts away from the motor, steering system,
wheels and all other moving components.
• Never hitch onto another vehicle or let yourself be pulled or pull anyone or
anything while riding the electric ride-on toy.
• Ride only on smooth, flat, dry surfaces such as pavement or level ground
without loose debris, such as sand, leaves, rocks or gravel. Water, mud, ice,
bumpy, un-even, slick, or rough surfaces could impair traction and contribute to
possible loss of control.
• Do not ride on or near hills or steep inclines. Ride only on level ground to avoid
tip over.
• Avoid sharp turns, bumps, drainage grates, and other obstacles.
• Do not ride at night or where there is limited visibility.
• Do not ride indoors or on surfaces that could become damaged such as carpet
or flooring.
• Do not ride on streets, around cars, or in foot or vehicle traffic.
• Regularly check the electric ride-on toy and its components. If any parts are
broken or worn, do not ride the electric ride-on toy until you have fixed or
replaced the broken or worn parts. Contact our Customer Service Team at
dynacraftwheels.com/contact for replacement parts.

5
• Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in
contact with wheels or other moving parts.
• Before each cycle of operation, you must perform the preoperation checks
specified in this manual or by the manufacturer, including:
– That all guards and pads originally supplied by the manufacturer are in proper
place and in serviceable condition;
– That the area that the unit is to be operated in is safe and suitable for safe
operation;
– That all safety labels are in place and understood by everyone, including the
riders;
– That any and all axle guards, chain guards, or other covers or guards supplied
by the manufacturer are in place and in serviceable condition; and
– That tires/wheels are in good condition and have sufficient tread remaining.
• Avoid sharp bumps, drainage grates, and sudden surface changes.
PRE-RIDE SAFETY CHECKLIST
• Check to make sure that all components are properly secured and are
functioning according to the manufacturer’s specifications.
• Components must be maintained and repaired and only with the manufacturer's
authorized replacement parts. Installation should be performed only by adult,
qualified personnel.
USING THE CHARGER
The charger should be examined regularly for damage to the cord, plug, enclosure
and other parts. In the event such damage has occurred, the electric ride-on toy
should not be charged until the charger has been repaired by qualified personnel
or replaced. Use only the supplied, recommended charger.
• Always use caution when charging.
• The charger is not a toy and should be operated by an adult.
• Never operate the charger near flammable materials or liquids, and operate the
charger in well-ventilated areas.
• Disconnect the charger and unplug it from the electric ride-on toy when not in use.
• Do not exceed the recommended charging time.
• Always disconnect the charger from the electric ride-on toy prior to wiping down
or cleaning the electric ride-on toy with any liquid.
WARNING: Never modify or alter the electrical system. Risk of fire. Do not bypass
the fuse. Replace only with 3A fuse, located under the seat. Alterations could cause a fire or
explosion resulting in serious injury or death and could also ruin the electrical system.
FAILURE TO HEED THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIALLY SERIOUS
INJURY. USE THE APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR APPROPRIATE
CLOTHING AND SHOES.

6
NOTE: Remove all packing and items from the display box. Make sure that the power
switch is turned "OFF" before assembling the electric ride-on toy.
ESTIMATED ASSEMBLY TIME
Because this ride-on toy is heavy and large, we strongly suggest two people to
complete assembly. You should allow approximately 60 minutes for assembly, not
including initial charging time. Initial charging can take approximately 18 hours (see
pages 15-16 for charging information).
If you experience a problem with this product, or are missing a part, please contact
our Customer Service Team at dynacraftwheels.com/contact, rather than return
this product to the store.
Please identify all parts before assembly and save all packaging material until
assembly is complete to ensure that no parts are discarded.
WARNING: DO NOT USE NON-ORIGINAL OR
NON-RECOMMENDED PRODUCTS WITH YOUR
ELECTRIC RIDE-ON TOY.
Altering of the original components or use of non-recommended replacement
parts may or may not be compatible with the design and will void the
warranty and may cause an unsafe condition resulting in serious injury or
death. Contact our Customer Service Team for original replacement parts at
dynacraftwheels.com/contact.
BEFORE YOU BEGIN ASSEMBLY B

7
1
2
3
4
5
67
89
6
7
8
9
11 10
12
13
14
15
16
17
18
13
21
20
19
22
23
24
25
26
C
NOTE: Some parts shown are assembled on both sides of ride-on toy. Parts
are packaged at both ends of box and in ride-on chassis. Ensure all parts are
present before assembly.
Phillips Screwdriver
(not included)
Tools Required
Needle-nose Pliers
(not included)
Socket Wrench
(included)
1 Plastic Body Assembly x1
2 M6 Lock Nut x2
3 Ø6 Washer x2
4 M6x16 Machine Screw x2
5 Front Wheel x2
6 Ø12 Washer x4
7 M10 Lock Nut x4
8 Split Pin x4
9 Axle Cap x4
10 Rear Axle x1
11 Rear Wheel x2
12 Steering Wheel Assembly x1
13 M5 Lock Nut x9
14 M5x35 Machine Screw x1
15 Seat Back x1
16 Seat Bottom x1
17 4x16 mm Round Head Screw x10
18 Front Rack Support x2
19 Rear Rack Support x2
20 M5x30 Machine Screw x8
21 Top Rack x1
22 Cross Arm x1
23 Controller x1
24 Battery & Battery Cover x1
25 Charger x1
26 17 mm Socket Wrench x2
27 Audio Input Cable x1
17
PARTS DIAGRAM
27

8
TOOLS REQUIRED:
ASSEMBLY
Your new ride-on toy requires adult assembly. Because your new ride-on toy is
heavy and large, we strongly suggest using two people to finish assembly. Set
aside around 60 minutes for assembly. Identify all parts before assembly and save
all packaging material until assembly is completed to ensure that no parts are
discarded.
17 mm Socket Wrench
(included)
WARNING: Children can be harmed by small parts, sharp edges and sharp points
in the ride-on toy's unassembled state, or by electrical items. In the unassembled state, this
package contains small parts. Adult assembly is required; children should not handle parts,
or help in assembly of the ride-on toy.
Phillips Screwdriver
(not included) Needle-Nose Pliers
(not included)
1. FRONT AXLE ASSEMBLY
• Gently turn the ride-on toy body upside down and cut off the plastic tie on the
front axle with scissors.
• Remove the M6x16 screw, washer and M6 locknut from the front axle.
• Adjust the front axle so that the axle is in the correct position as shown below;
then reinsert the M6x16 screw as shown, making sure the M6x16 screw goes
through the holes in metal plates A and B (ensure plate A sits over plate B
as shown with the stopper, to prevent fingers from becoming trapped while
steering); attach the washer and locknut and tighten securely with an adjustable
wrench or needle-nose pliers. NOTE: Do not over-tighten.
• Repeat above operation for the front axle on the other side.
M6x16
Machine Screw
Ø6 Washer
M6 Locknut
AA
BBAB
AB
Front Axle Stopper Stopper Front Axle
Stopper
WARNING: Make sure front axle assembly is properly secured before letting
anyone use the ride-on toy.
D

9
2. FRONT WHEEL ASSEMBLY
• Remove all parts from front axle.
• Find a front wheel labeled "FRONT", slide
the wheel onto the axle.
• Install a Ø12 washer and M10 locknut, then
tighten it with the 17 mm socket wrench.
NOTE: Do not over-tighten. For your safety, make
sure you insert a split pin into the hole in the end
of front axle, and split it with standard needle-
nose pliers.
• Insert the axle cap until it clicks into place.
• Repeat above operation for the front wheel
on the other side. Split Pin
Front Axle Front Wheel
Split Pin
Axle Cap
Ø12
Washer
M10
Lock Nut
Split Pin
3. REAR AXLE ASSEMBLY
• Remove all parts from the rear axle.
• Cut off the plastic tie on the left gear box
and lift it as shown, ensure that the hole in
the left gear box sits in line with the hole in
the ride-on toy body.
• Insert the rear axle through the hole in
the ride-on toy, following the direction of
the arrow as shown. When the rear axle is
halfway through, lift the other gear box so
that the rear axle can protrude through it.
NOTE: Make sure that the rear axle is centered
with left and right ends exposed the same
distance outside of the ride-on toy body.
Rear Axle
Gear Box's Hole

10
4. REAR WHEEL ASSEMBLY
• Find a rear wheel labeled "REAR", slide
the wheel onto the rear axle and make it
match up with the gear box.
• Insert a Ø12 washer onto the axle.
• While holding the rear axle with a 17mm
socket wrench, fit the M10 locknut to
the end of the rear axle with another
17 mm socket wrench. DO NOT over
tighten; the rear axle ends are supposed
to be exposed; 1-2 threads exposed is
acceptable.
• For your safety, insert a split pin into the
hole in the end of rear axle, and split it
using standard needle nose pliers.
• Insert the axle cap until it clicks into place.
• Repeat above operation for the rear wheel
on the other side.
Gap
Front AxleFront Wheel
Split Pin
Axle Cap
Ø12
Washer
M10
Lock Nut
Split Pin Split Pin
IMPORTANT! CHECK WHEEL GAP
After assembling any wheel onto the axles,
check the gap between the screw thread
and the outside of the wheel (refer to the
adjacent diagram).
If the gap is too big, add two or three
washers on the axle to the inside of the
wheel. After tightening the nut on the outside
of the wheel, spin the wheel to check if the
wheel spins smoothly. If the wheel gets
caught or does not spin smoothly, the
friction may cause damage to the motor. Try
increasing the gap by removing one or two
washers to ensure the wheel spins smoothly.
NOTE: If the wheel nuts are loose, the
wheels will not engage the forward
gear. Tighten the nut with the socket
wrench.
WARNING: Make sure that the axle assemblies and wheels are properly tightened
and secure before letting anyone use the ride-on toy. Failure to do so may result in a loss of
control and serious injury or death.

11
STEERING WHEEL BATTERY SAFETY INFORMATION:
Batteries may leak fluids that can cause chemical burn, injury or ruin your product.
To avoid battery leakage:
• Install batteries correctly, observing the polarity (+/-) signs to avoid leakage.
• Do not mix old and new batteries.
• Do not mix batteries of different types: alkaline, standard (carbon-zinc) or
rechargeable (NiMH).
• Remove the batteries from the battery compartment when the unit will not be
used for an extended period of time.
• Always remove exhausted batteries from the battery compartment.
• Do not dispose of batteries in fire.
• Do not short circuit the supply terminals.
• Replace the batteries when the horn sounds become distorted.
• Non-rechargeable batteries should not be recharged.
• Use only batteries of the same or equivalent type as recommended.
• If rechargeable batteries are used, they should only be charged by an adult.
• Remove rechargeable batteries from the product before charging.
• Battery chargers used with toys must be examined regularly for damage to the
cord, plug, enclosure and other parts. In the event that such damage is found,
the toy must not be used with the battery charger until the damage has been
repaired.
6. STEERING WHEEL BATTERIES
INSTALLATION
NOTE: Batteries are not included.
• Unscrew the screw in the steering wheel and
remove the cover.
• Insert 2x 1.5V size AA AM-3 or LR6
batteries.
• Replace the cover and tighten the screw
to secure it in place. Battery
Compartment Cover
5. STEERING WHEEL ASSEMBLY
• Gently turn the ride-on toy body upright.
• Remove the M5x35 machine screw and M5
locknut from the steering wheel.
• Insert the steering wheel onto the end of
the steering column, line up the hole in the
steering wheel and the hole in the steering
column, reinsert the M5x35 machine screw
as shown, and tighten it with M5 locknut
securely.
Steering
Column M5x35 Machine
Screw
M5 Locknut
WARNING: Make sure that the steering wheel is securely fastened and that the
steering functions properly before letting anyone use the ride-on toy.

12
7. TOP RACK ASSEMBLY
• Find the top rack and its cross arm.
• The cross arm is marked with “F” and “R”
on its two ends. Find the corresponding
“F” and “R” markings on the top rack and
fit the cross arm to the corresponding spot
as shown in the diagram.
• Secure the cross arm to the top rack with
two 4x16 mm round head screws . Cross Arm
8. RACK FRONT SUPPORTS
ASSEMBLY
• Find one Front Support marked with an
“R1” and remove the M5x30 machine
screw and M5 locknut from it. Attach the
support to the corresponding U shaped
support also marked with an “R1”. Reinsert
the M5x30 machine screw as shown, and
tighten it with M5 locknut securely, as
shown at right.
• Find the other Front Support marked with
an “L1” and remove the M5x30 machine
screw and M5 locknut from it. Attach the
support to the corresponding U-shaped
support also marked with an “L1”. Reinsert
the M5x30 machine screw, and tighten it
with M5 locknut securely.
4x16 Round
Head Screw
M5x30 Machine
Screw
M5 Locknut
Front Rack
Support
R1 R1 L1
L1
Top Rack
U Shaped
Support

13
10. RACK ASSEMBLY
INSTALLATION
• Insert the Front and Rear rack supports
into the four corresponding holes in the
ride-on toy body as shown in diagram 1.
• Secure each of the Front Rack Supports
using one 4x16 mm round head screw on
each side, as shown in diagram 2.
• Secure each of the Rear Rack Supports
using two 4x16 mm round head screws on
each side, as shown in diagram 3.
Rear Rack
Support
Front Rack
Support
9. RACK REAR SUPPORTS
ASSEMBLY
• Find one Rear Support marked with an
“R2” and remove the M5x30 machine
screw and M5 locknut from it.
• Attach the support to the corresponding
U shaped support also marked with an
“R2”. Reinsert the M5x30 machine screw
as shown, and tighten it with M5 locknut
securely, as shown at right.
• Find the other Rear Support marked with
an “L2” and remove the M5x30 machine
screw and M5 locknut from it.
• Attach the support to the corresponding U
shaped support also marked with an “L2”.
Reinsert the M5x30 machine screw, and
tighten it with M5 locknut securely.
Rear Rack Support
M5x30 Machine
Screw
M5 Locknut
1
2
3
4x16 Round
Head Screw
4x16 Round
Head Screw
R2
L2 R2
L2

14
Seat Back
Seat Bottom
4x16 Round
Head Screw
M5x16
Machine Screw
12 SEAT INSTALLATION
• Find Seat Bottom and Seat Back, locate
and insert the Seat Back into the Seat
Bottom as shown.
NOTE: Gently insert the Seat Back tabs into the
corresponding seat bottom slots and push until
you hear the seat back click into place. Once the
tabs click into place, the seat back cannot be
pulled out without damaging the seat.
• Slide the seat into the place as shown.
• Tighten the seat with two 4x16 round head
screws and two M5x16 machine screws
(which come attached to the seat bottom).
11. POWER SUPPLY
CONNECTION
NOTE: The battery is disconnected for shipment
to prevent the battery from draining.
• Securely plug the battery connector into
the wire connector.
Wire
Connector
Battery
Connector
Battery

15
BATTERY CHARGING
IMPORTANT! Before first time use, charge the battery for at least 18 hours. Charge
the battery for at least 12 hours after each use of the ride-on toy. Never charge
the battery longer than 30 hours. Overcharging or undercharging the battery may
shorten battery life and decrease ride-on toy running time.
WARNING: Battery can fall out and injure a child if the ride-on toy tips over.
Always use battery cover.
PREVENT FIRE
• Never modify the electrical system.
• Alterations could cause a fire resulting in serious injury and could also ruin the
electrical system.
• Use of the wrong type battery or charger could cause a fire or explosion,
resulting in serious injury.
• Use of non-original components on this ride-on toy could cause overheating, fire
or explosion.
• The battery must be handled by adults only.
• The battery is heavy and contains sulfuric acid (electrolyte).
• Dropping the battery could result in serious injury.
• Never allow children to charge the battery.
• Battery charging must be done by adults only. A child could be injured by the
electricity involved in charging the battery.
• Never lift or carry the battery by the wires or connector, this can damage the
battery and possibly cause a fire resulting in serious injury. Lift and carry the
battery by the case only.
• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage
each time you charge the battery.
• If damage or excessive wear is detected, do not use the charger or the battery
until you have replaced the worn or damaged part.
WARNING: Use the charger in dry locations only.
IMPORTANT NOTE
• We recommend that you start charging your battery before beginning assembly
of your new ride-on toy.
• The battery must be upright while charging.
• The charger is not a toy, and should only be operated by adults.
• Do not short-circuit the battery.
• You do not need to remove the battery from your ride-on toy to recharge it.
• Before charging the battery, examine the battery case for cracks and other damage
which may cause sulfuric acid (electrolyte) to leak during the charging process. If
damage is detected, do not charge the battery or use it in your ride-on toy. Battery
acid is very corrosive and can cause severe damage to surfaces it contacts.

16
• Do not charge the battery on a surface (such as a kitchen counter top) which
could be damaged by the acid contained inside the battery. Take precautions to
protect the surface on which you charge your battery.
• Use only an original charger (AC 120V 60Hz) with an output of DC 24V (1A) to
charge your ride-on toy battery.
• NOTE TO ADULTS: Regularly examine the charger for damage to the cord, plug,
housing or other parts that may result in the risk of fire, electric shock or injury.
• If your battery is old and will not accept a charge, do not leave it in the ride-on toy.
Always remove a dead battery from the ride-on toy.
• After the first charge, recharge the battery for at least 12 hours after each use.
Never charge the battery longer than 30 hours. Charge the battery after each use,
regardless of how long the ride-on toy was used.
• Do not allow the battery to run down completely before charging.
• Charge the battery before storing the ride-on toy.
• Charge the battery at least once per month, even if the ride-on toy has not been used.
NOTE:
• This product has CHARGING PROTECTION: when charging, all the functions will
be cut off.
• Recharges after initial charge - At least 12 hours, and never charge the battery
longer than 30 hours.
• When the ride-on toy begins to run slowly, recharge the battery.
• After each use, or at least once per month when not in use, recharge the battery
for at least 12 hours and less than 30 hours at most.
WARNING: Use the charger in dry locations only.
1. Plug the charger port into the input socket (the socket is under the seat).
2. Plug the charger plug into a wall outlet. The battery will begin charging.
NOTE: Red LED light indicates battery is charging and a green LED light indicates
battery is nearly fully charged. (If the lights on the charger do not light up, check the
power to the outlets.) If you have any charging questions or issues, please make
sure that you have charged your unit according to the recommended charging times
outlined in this manual, i.e., at least 18 hours before first use and at least 12 hours
after each subsequent use, before contacting our Customer Service Team.
Charging Input
Socket
1
2

17
HOW TO USE YOUR RIDE-ON TOY
Forward/Reverse
Shift Lever
Sound Buttons
Foot Pedal
POWER SWITCH
• Turn the ride-on toy on or off.
FOOT PEDAL
• To move the car, press the foot pedal down.
• To stop, take your foot off the foot pedal.
FORWARD-REVERSE SHIFT LEVER
• To move the car forward at high speed, shift the lever to the “High” position.
• To move the car forward at low speed, shift the lever to the “Low” position.
• To move the car backward, shift the lever to the “Reverse” position.
NOTE: Use low speed until you get familiar with your new ride-on toy.
SOUND BUTTON
To activate sound, press the button on the steering wheel.
STOP
To stop the ride-on toy, you must take your foot off the pedal.
WARNING: The ride-on toy does not have brakes. Do not park or ride on any
slopes or steep inclines.
WARNING: For your safety, this ride-on toy has been designed with a one second
delay start. When the pedal is pressed, the ride-on toy will start to move one second later.
WARNING: Use low speed until you get familiar with your new ride-on toy.
Power Switch
Audio Input Jack
(Audio Input Cable Included)
E

18
Audio Input Jack
Use the Audio input cable (Included) to connect your MP3 player or other
compatible audio device with this ride-on toy to listen to and enjoy music.
1. Plug one end of the audio input cable (Included) into the audio input jack on the
ride-on toy as shown.
2. Plug the other end of the audio input cable into the headphone jack on your
audio device or MP3 player.
3. Adjust your audio device or MP3 player volume to low level.
4. Then adjust the volume to increase or decrease its sound level as desired.
NOTE: MP3 player or Audio Device not included.
WARNING: Do not let use of the sound buttons, an MP3 player, or other audio
devise interfere with safe riding.
WARNING:
• Maximum load weight on the cargo bed is 11 lb (5 kg).
• No stepping on or in cargo bed.
• No climbing on or in cargo bed.
• Never ride in cargo bed.
WARNING: For your safety, this ride-on toy has been designed with a one second
delay start. When the pedal is pressed, the ride-on toy will start to move one second later.
Audio Input Jack
Audio Input Cable
(Included)

19
IMPORTANT
• Always stop ride-on toy when changing the direction to avoid damage to the
gears and motor.
• This ride-on toy has an adjustable seat belt; instruct children on how to fasten
the seat belt before using.
• Do not let any child touch the wheels or be near them when the ride-on toy is
moving.
• To avoid accidents, inspect the ride-on toy before riding to ensure that it is in
proper working order and safe to ride.
• This toy has no brake; to stop, remove foot from the foot pedal.
• Check all the screws, cap nuts and protective coverings regularly and tighten as
required. Check plastic parts on a regular basis for cracks or broken pieces.
• Your new battery must be charged for at least 18 hours before you use it in your
ride-on toy for the first time.
• Do not wash the ride-on toy with water; clean it with a cloth.
SAFETY PRECAUTIONS
• Children must have adult supervision at all times.
• Do not ride on the road, footpaths, near pools, or bodies of water.
• Do not allow children under the recommended age to ride the ride-on toy; refer
to the age grading.
• Do not allow riders over the recommended weight rating or outside of the
recommended age range to use the ride-on toy.
• To stop the ride-on toy, you must take your foot off the pedal.
• Charging should only be done by an adult.
• An adult must teach the child how to operate the ride-on toy.
• Do not ride on hills or slopes, in sand or on other soft, wet, or slippery surfaces.
• Do not use a different size battery. Use only original or recommended
replacement batteries.
• The ride-on toy is designed to carry only a maximum weight of 130 lb at a time.
Never allow more than two riders or over-load the ride-on toy.
• This product should be assembled and checked by adults before use.
WARNING: This ride-on has no brake; to stop take foot off foot pedal. Do not park
or ride on any slopes or steep inclines.