Dynacraft Realtree User manual

this manual contains important safety, performance and
maintenance information. read the manual before taking your
first ride or allowing your child to ride your new electric
ride-on toy. keep the manual handy for future reference.
24V UTV
OWNER’S MANUAL
FOR AGES 3+
MAXIMUM WEIGHT: TOTAL 130lb (59 kg), 65lb (29.5kg) per seat
DO NOT RETURN THIS ITEM TO THE STORE
CONTACT DYNACRAFT CUSTOMER SERVICE FOR ASSISTANCE
dynacraftwheels.com/contact
or 1-800-551-0032 9 AM – 5 PM ET
NOTE: Illustrations in this Manual are for reference purposes only and may not reflect the
exact appearance of the actual product. Specifications are subject to change without notice.

1
AIntroduction, Safety and Warnings . . . . . . . . . . . . . . . . 2
BBefore You Begin Assembly . . . . . . . . . . . . . . . . . . .6
CParts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
EHow to Use Your Ride-on Toy . . . . . . . . . . . . . . . . . 19
FDetailed Maintenance and Repair . . . . . . . . . . . . . . . 22
GTroubleshooting Guide . . . . . . . . . . . . . . . . . . . . . 28
HLimited Warranty . . . . . . . . . . . . . . . . . . . . . . . 31
SUITABLE AGE . . . . . . . . . . . . . . . . . . . . . . . . . . 3+
CAPACITY. . . . . . . . . . . . . . . . . . . . .Up to 130 lb (59 kg)
MAX SPEED. . . . . . . . . . . . . . .Low 2.5 MPH/High 5.0 MPH
CHARGER / INPUT. . . . . . . . . . . . . . . . . . .AC120V /60HZ
OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . .DC 24V/1A
CHARGING . . . . . . . . . . . . . . . . . . . . . . . 12-18 Hours
BATTERY . . . . . . . . . . . . . . . . . . . . 24V 7AH, 1x Battery
SIZE. . . . . . . . . . . . . . . . . . . . . 1440 x 900 x 1230 mm
AVERAGE BATTERY LIFE . . . . . . . . . . . . . . . . 300 Charges
TABLE OF CONTENTS
SPECIFICATIONS

INTRODUCTION, SAFETY AND WARNINGS A
ABOUT THIS MANUAL: This Manual was written to help you and your child get
the most performance, comfort, enjoyment and safety when riding your new
electric ride-on toy. It is important for you to understand your new electric ride-on
toy. By reading this manual before you let your child go out on his/her first ride,
you will know how to get the most from your new electric ride-on toy. It is also
important that you or your child’s first ride be in a controlled environment, away
from cars, obstacles, and other riders.
GENERAL WARNING: Riding an electric ride-on toy can be a dangerous
activity, even under the best of circumstances. Proper maintenance of your new ride-on toy is
your responsibility and helps reduce the risk of injury. Certain conditions may cause components
to fail without fault of the manufacturer. The ride-on toy can and is intended to move, and it is
therefore possible to lose control, fall off and/or get into dangerous situations that no amount of
care, instruction or expertise can eliminate. If such a thing does occur, your child can become
seriously injured or die, even when using safety equipment and other safety precautions.
WARNING: To reduce risk of injury, adult supervision is required. Never use in
roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other
bodies of water; always wear shoes, and never allow more than two (2) riders.
WARNING: CHOKING HAZARD–Small parts not suitable for children under 3 years old.
WARNING: This toy is unsuitable for children under 3 years due to its maximum speed.
WARNING: This toy should be used with caution since skill is required to avoid
falls or collisions causing injury to the user or third parties. Parents must make sure that
children can operate the ride-on toy safely before letting them ride it.
WARNING: Do not ride in rain, snow, or mud, or store the ride-on toy outside without
covering. Water can damage components, including the motor, electrical system, and battery.
WARNING: This ride-on toy is not an off-road vehicle and is intended to be ridden
on smooth, level ground. Do not ride in loose dirt, sand, or gravel, which could damages
moving parts, the motor, or the electrical system.
NOTE: Store the ride-on toy indoors when not in use or in a covered location. Avoid long
term exposure to rain, excessive sun, or other inclement weather.
RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE. This manual
contains many warnings and cautions concerning the consequences of failing to inspect,
maintain or properly use your electric ride-on toy. Because any fall can result in serious
injury or even death, we do not repeat the warning of possible serious injury or death each
time such a possibility is mentioned in this manual or the risk of falling leads to a warning.
ALWAYS USE PROPER RIDING ATTIRE. Always wear appropriate clothing and shoes.
Never ride barefoot or in sandals and make sure that shoelaces or other fasteners are tied
and kept away from the wheels and drive system of the ride-on toy.

3
RIDER USE AND REQUIRED PARENTAL SUPERVISION
RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 130 LB (59 KG) AND
MUST BE OVER 3 YEARS OLD. NEVER ALLOW MORE THAN 2 CHILDREN TO
RIDE THE RIDE-ON TOY SIMULTANEOUSLY.
The age grade for the electric ride-on toy is for 3 years and older. Just because
your child is within the age and weight limitations specified for the electric ride-
on toy, does not mean that his/her size is appropriate to fit or maintain control of
the electric ride-on toy, or that he/she is capable of safely operating the electric
ride-on toy. You are the best judge of whether you or your child can safely operate
the electric ride-on toy; this includes determining whether your child is at the
appropriate developmental stage for safe use of the electric ride-on toy. Any rider
that is unable to fit comfortably on the electric ride-on toy should never attempt to
ride it. A parent's decision to allow their child to use the electric ride-on toy should
be based on the child's maturity, skill and their ability to follow rules. Remember
that the electric ride-on toy is intended for use only by children who are, at a
minimum, able to comfortably and safely operate it.
Children operating the electric ride-on toy should be supervised by an adult at all
times. Parents should ensure that children only use the electric ride-on toy safely
and within their age and physical limits.
This manual contains very important safety information. It is your responsibility to
completely review this information and make sure that all riders understand all of
the warnings, cautions, instructions and safety topics addressed in this manual
and to assure that all riders are able to safely and responsibly use the electric
ride-on toy. You should periodically review and reinforce all information in this
manual with all riders, especially children. You should also regularly inspect and
maintain your electric ride-on toy to ensure the safety of all riders. Make sure that
your new electric ride-on toy is properly fitted to any child riding it; that it is in good
repair and safe operating condition; that you and your child have gone over the
use, operation and safety information in this manual; that you and your child have
learned and understand what to do and what not to do with your new electric ride-
on toy, including observing all applicable laws, rules and common sense.
Children should be made aware of all possible riding hazards and correct riding
behavior before they ride the electric ride-on toy and should be supervised by an
adult at all times. Please explain the following to them as often as necessary.

4
SAFE RIDING PRACTICES AND WARNINGS
• Check and obey all local laws or regulations which may be in effect in the
locations where the electric ride-on toy may be used.
• Always wear appropriate clothing and shoes.
• Observe the age and weight limitations on the cover of this manual.
• Always stay seated while riding the electric ride-on toy.
• Children must be supervised by an adult at all times to be safe.
• Always be alert and ride your electric ride-on toy defensively. Watch out for
obstacles that could catch one of the electric ride-on toy's wheels or force you to
turn suddenly and/or lose control. Be careful to avoid pedestrians, persons using
other wheeled products (including roller or in-line skates, skateboards, scooters,
bikes, etc.), children or animals who may enter your path. Always respect the
rights and property of others.
• Do not activate the foot pedal unless you are seated in the ride-on toy and in a
safe, outdoor environment that is suitable for riding your electric ride-on toy.
• Do not attempt or perform any stunts or tricks on the electric ride-on toy. It is not
made to withstand such misuse and abuse.
• Keep both hands on the steering wheel at all times.
• Do not touch the motor on the electric ride-on toy when in use or directly after
use as these parts can become extremely hot.
• Never allow more than two persons to ride the electric ride-on toy at one time
and never try to tow anything.
• Do not use near steps, water, or swimming pools.
• Do not ride in wet weather.
• Never immerse the electric ride-on toy in water; electrical and drive components
could be damaged by water or create other potentially unsafe conditions.
• Keep your fingers and other body parts away from the motor, steering system,
wheels and all other moving components.
• Never hitch onto another vehicle or let yourself be pulled or pull anyone or
anything while riding the electric ride-on toy.
• Ride only on smooth, flat, dry surfaces such as pavement or level ground without
loose debris, such as sand, leaves, rocks or gravel. Water, mud, ice, bumpy,
uneven, slick, or rough surfaces could impair traction and contribute to possible
loss of control.
• Do not ride on or near hills or steep inclines. Ride only on level ground to avoid
tip over.
• Avoid sharp turns, bumps, drainage grates, and other obstacles.
• Do not ride at night or where there is limited visibility.
• Do not ride indoors or on surfaces that could become damaged such as carpet
or flooring.
• Do not ride on streets, around cars, or in foot or vehicle traffic.
• Regularly check the electric ride-on toy and its components. If any parts are
broken or worn, do not ride the electric ride-on toy until you have fixed or
replaced the broken or worn parts.

5
• Do not to allow hands, feet, hair, body parts, clothing, or similar articles to come
in contact with wheels or other moving parts.
• Before each cycle of operation, you must perform the preoperation checks
specified in this manual or by the manufacturer, including:
– That all guards and pads originally supplied by the manufacturer are in proper
place and in serviceable condition;
– That the area that the unit is to be operated in is safe and suitable for safe
operation;
– That all safety labels are in place and understood by everyone, including the
riders;
– That any and all axle guards, chain guards, or other covers or guards supplied
by the manufacturer are in place and in serviceable condition; and
– That tires/wheels are in good condition and have sufficient tread remaining.
• Avoid sharp bumps, drainage grates, and sudden surface changes.
PRE-RIDE SAFETY CHECKLIST
• Check to make sure that all components are properly secured and are
functioning according to the manufacturer’s specifications.
• Components must be maintained and repaired and only with the manufacturer's
authorized replacement parts. Installation should be performed only by adult,
qualified personnel.
USING THE CHARGER
The charger should be examined regularly for damage to the cord, plug, enclosure
and other parts. In the event such damage has occurred, the electric ride-on toy
should not be charged until the charger has been repaired by qualified personnel
or replaced. Use only the supplied, recommended charger.
• Always use caution when charging.
• The charger is not a toy and should be operated by an adult.
• Never operate the charger near flammable materials or liquids, and operate the
charger in well-ventilated areas.
• Disconnect the charger and unplug it from the electric ride-on toy when not in use.
• Do not exceed the recommended charging time.
• Always disconnect the charger from the electric ride-on toy prior to wiping down
or cleaning the electric ride-on toy with any liquid.
WARNING: Never modify or alter the electrical system. Risk of fire. Do not bypass
the fuse. Replace only with 3A fuse, located under the seat. Alterations could cause a fire or
explosion resulting in serious injury or death and could also ruin the electrical system.
FAILURE TO HEED THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIALLY SERIOUS
INJURY. USE THE APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR APPROPRIATE
CLOTHING AND SHOES.

6
Remove all packing and items from the display box.
NOTE: Parts are packaged at both ends of box and in ride-on chassis. Ensure all parts are
present before assembly.
ESTIMATED ASSEMBLY TIME
Because this ride-on toy is heavy and large, we strongly suggest two people to
complete assembly. Allow approximately 60 minutes for assembly by two people,
not including initial charging time. Initial charging can take approximately 18 hours
(see page 17 for charging information).
If you experience a problem with this product, or are missing a part, please contact
our Customer Service Team at dynacraftwheels.com/contact, rather than return
this product to the store.
Please identify all parts before assembly and save all packaging material until
assembly is complete to ensure that no parts are discarded.
BEFORE YOU BEGIN ASSEMBLY
WARNING: DO NOT USE NON-ORIGINAL OR
NON-RECOMMENDED PRODUCTS WITH YOUR
ELECTRIC RIDE-ON TOY.
Altering of the original components or use of non-recommended
replacement parts may or may not be compatible with the design and
will void the warranty and may cause an unsafe condition resulting in
serious injury or death.
B

7
PARTS DIAGRAM C
NOTE: Some parts shown are assembled on both sides of ride-on toy. Parts are packaged
at both ends of box and in ride-on chassis. Ensure all parts are present before assembly.
1. Roof x1
2. U shape Support x2
3. Roof Front Support x2
4. Steering Wheel Assembly x1
5. Cargo Basket x1
6. Plastic Body Assembly x1
7. Ø19 Front Axle Washer x2
8. Front Wheel x2
9. Ø12 Washer x4
10. M10 Lock Nut x4
11. Split Pin x4
12. Axle Cap x4
13. Rear Wheel x2
14. Rear Axle x1
15. Battery x1
16. Cargo Bed (5 pcs)
17. Seat (2 pcs)
18. Roof Rear Support x2
19. Charger x1
20. 17 mm Socket Wrench (for wheels) x2
21. M5x35 Machine Screw x1
22. M5 Lock Nut x1
23. M5 x 16 mm Screw x6
24. 4x16 mm Round Head Screw x16
25. Controller x1
26. 4x12 mm Round Head Screw x11
1
2
3
4
21
22
23
23
24 26
5
6
7
8
9
11 10
9
13 26 14
15
17
18
19
20
16
16
25
11 10
12

1. CARGO BED ASSEMBLY
• Find the plastic board marked with “1” on its back.
• Find other two boards that marked with “2” and “3”, and push them horizontally
until they sit well as shown.
• Find a plastic board marked with “4” on its back, and push it vertically until you
hear it click into.
• Find a plastic board marked with “5”, there are slots along two side of it, slide it
into the sticking tabs on “2” and “3” as shown, making sure the door is secure.
• Gently turn the cargo bed upside down, use three 4x12 round head screws to
tighten properly.
4x12 mm
Round Head Screw
8
TOOLS REQUIRED:
ASSEMBLY
Your new ride-on toy requires adult assembly. Because your new ride-on toy is
heavy and large, we strongly suggest using two people to finish assembly. Set
aside around 60 minutes for assembly. Identify all parts before assembly and save
all packaging material until assembly is completed to ensure that no parts are
discarded.
17 mm Socket Wrench
(included)
WARNING: Children can be harmed by small parts, sharp edges and sharp points
in the ride-on toy's unassembled state, or by electrical items. In the unassembled state, this
package contains small parts. Adult assembly is required; children should not handle parts,
or help in assembly of the ride-on toy.
Phillips Screwdriver
(not included)
Needle-Nose Pliers
(not included)
5
3
2
1
4
D

9
2. CARGO BED INSTALLATION
• Align the cargo bed assembly with the four screw holes on the ride-on toy body.
Use four M5x16 machine screws to tighten each corner securely.
M5x16 mm
Machine Screw
M5x16 mm
Machine Screw
Finished Status
1
2
3
M5x16 mm Machine
Screw

10
4. REAR WHEEL ASSEMBLY
• First, remove all washers and nuts from
the rear axle.
• Insert the rear axle through the hole in
the ride-on toy body as shown, making
sure the axle exposure at the left and right
ends are equal.
3. FRONT WHEEL ASSEMBLY
• Turn the ride-on toy body upside down (this
should be handled carefully by two adults)
• Cut the tie on the front axle with scissors.
• Adjust the front wheel axle until the axle
clicks into position to ensure that it is
secure for safety (see Figure A).
• Remove washers and nuts from the front
wheel axle.
CAUTION: To avoid pinching your
fingers, do not put your hand into the slot when
adjusting the front wheel axle.
• Fit a Ø19 washer onto the axle.
• Find a front wheel marked with an “R” and
labeled "Front". Find the “R” marking on the
front of the ride-on toy body to match this
wheel and slide the wheel onto the axle.
NOTE: Refer to the below drawing showing "R"
and "L" location on ride-on toy body.
• Fit a Ø12 washer and M10 locknut onto the
axle, then tighten it with socket wrench.
• Insert the axle cap until it clicks into place.
• Find the other front wheel, marked with an
“L” and labeled with and “Front”. Find the
“L” marking on the front end of the ride-on
toy body to match this wheel and slide the
wheel onto the axle. Secure this wheel with
the same steps as the other front wheel
above.
• Front wheels should spin freely;
if not, loosen nut slightly.
Front Axle
Wheel Axle
Front Wheel
Ø12
Washer
Ø19
Washer
Spilt Pin
Spilt Pin
Spilt Pin
M10
Lock Nut
Axle Cap
A
B
NOTE: Do not over-tighten. For your safety, make
sure you insert a split pin into the hole in the end
of front axle, and split it using standard needle
nose pliers.
Front
Rear Axle
"L" "R"

11
• Find a rear wheel marked with an “R” and
labeled “Rear”. Find the “R” marking at the
rear end of the ride-on toy body to match
this wheel and slide the wheel onto the axle.
• Insert a Ø12 washer onto the axle.
• While holding the rear axle with a 17 mm
socket wrench, fit the M10 locknut to the
end of the rear axle with another 17 mm
socket wrench. DO NOT over tighten; the
rear axle ends are supposed to be exposed;
1-2 threads exposed is acceptable.
• For your safety, insert a split pin into the
hole in the end of rear axle, and split it
using standard needle nose pliers. (Refer
to the drawings illustrated for front wheel at
page 9).
• Insert the axle cap.
• Find the other rear wheel, marked with an
“L” and labeled with and “Rear”. Find the
“L” marking at the rear end of the ride-on
toy body to match this wheel and slide the
wheel onto the axle. Secure this wheel with
the same steps as the other rear wheel
above.
Rear Axle
Rear Wheel
Ø12
Washer
Axle Cap
M10
Lock Nut
Split Pin
Rear
IMPORTANT! CHECK WHEEL GAP
After assembling any wheel onto the axles,
check the gap between the screw thread
and the outside of the wheel (refer to the
adjacent diagram).
If the gap is too big, add two or three
washers on the axle to the inside of the
wheel. After tightening the nut on the outside
of the wheel, spin the wheel to check if the
wheel spins smoothly. If the wheel gets
caught or does not spin smoothly, the
friction may cause damage to the motor. Try
increasing the gap by removing one or two
washers to ensure the wheel spins smoothly.
NOTE: If the wheel nuts are loose, the
wheels will not engage the forward
gear. Tighten the nut with the socket
wrench.
Gap

12
STEERING WHEEL BATTERY SAFETY INFORMATION:
Batteries may leak fluids that can cause chemical burn, injury or ruin your product.
To avoid battery leakage:
• Install batteries correctly, observing the polarity (+/-) signs to avoid leakage.
• Do not mix old and new batteries.
• Do not mix batteries of different types: alkaline, standard (carbon-zinc) or
rechargeable (NiMH).
• Remove the batteries from the battery compartment when the unit will not be
used for an extended period of time.
• Always remove exhausted batteries from the battery compartment.
• Do not dispose of batteries in fire.
• Do not short circuit the supply terminals.
• Replace the batteries when the horn sounds become distorted.
• Non-rechargeable batteries should not be recharged.
• Use only batteries of the same or equivalent type as recommended.
• If rechargeable batteries are used, they should only be charged by an adult.
• Remove rechargeable batteries from the product before charging.
• Battery chargers used with toys must be examined regularly for damage to the
cord, plug, enclosure and other parts. In the event that such damage is found,
the toy must not be used with the battery charger until the damage has been
repaired.
6. STEERING WHEEL BATTERIES
INSTALLATION
NOTE: Batteries are not included.
• Unscrew the screw in the steering wheel and
remove the cover.
• Insert 2x 1.5V size AA AM-3 or LR6
batteries.
• Replace the cover and tighten the screw
to secure it in place.
Battery Compartment
Cover
5. STEERING WHEEL ASSEMBLY
• Gently turn the ride-on toy body upright.
• Remove the M5x35 machine screw and nut
from the steering wheel.
• Insert the steering wheel onto the end of
the steering column, line up the hole in the
steering wheel and the hole in the steering
column, reinsert the M5x35 machine
screw as shown, and tighten it with M5 nut
securely.
Steering
Wheel
Screwdriver
M5x35
Machine
Screw
M5 Nut
DC 1.5V (SIZE AA)
DC 1.5V (SIZE AA)
-++
-
++

13
7. ROOF ASSEMBLY
• Find the roof and two U shape supports as
shown.
• The U shaped supports are marked
with either an “L” or “R”. Find the
corresponding “L” and “R” markings on
the roof panel and then fit each U shaped
support to the corresponding spot on the
roof panel as shown in the diagram to the
right.
• Secure the U shaped supports to the roof
using 3 4x16 mm round head screws on
each support, as shown in the diagram at
right.
8. ROOF FRONT SUPPORTS
ASS EM BLY
• Find one Front Support marked with an
“R” and attach it to the corresponding U
shaped support also marked with an “R”.
Use two 4x12 mm Round head screws to
secure the supports, as shown at right.
• Find the other Front Support, marked with
an “L” and attach it to the corresponding U
shaped support also marked with an “L”.
Use two 4x12 mm round head screws to
secure the supports, as shown at right.
4x16 Round
Head Screw
4x12 Round
Head Screw
4x12 Round
Head Screw
“R” Mark
“L” M ar k
Front
Supports
U Shape
Support
"L" "R"

14
9. ROOF REAR SUPPORTS
ASS EM BLY
• Find the Rear Support marked with an
“R” and attach it to the corresponding U
shaped support also marked with an “R”.
Use two 4x12 mm round head screws to
secure the supports, as shown at right.
• Find the other Rear Support, marked with
an “L” and attach it to the corresponding
U shaped support also marked with an “L”.
Use two 4x12 mm round head screws to
secure the supports as shown at right.
4x12
Round
Head
Screw
4x12 Round
Head
Screw
Roof Rear
supports
“R” Mark
“L” M ar k
10. ROOF ASSEMBLY
INSTALLATION
• Insert the Front and Rear roof supports
into the four corresponding holes in the
ride-on toy body as shown in diagram 1.
• Secure each of the Front Roof Supports
using a 4x16 mm round head screw on
each side, as shown in diagram 2.
• Secure each of the Rear Roof Supports
using two 4x16 mm round head screws on
each side, as shown in diagram 3.
4x16 Round
Head Screw
Rear Roof
Support
Bracket
4x16 Round
Head Screw
Front Roof
Support
1 2
3

15
11. CARGO BASKET ASSEMBLY
• Place the Basket into the four correspond-
ing holes in the Hood and push down
until it clicks into place. Use four 4x16 mm
round head screws to secure the basket to
the Hood, as shown in diagram 1.
• If you do not want the Basket on the Hood,
find the four small end caps supplied in
the bag with the owners manual (diagram
2) and snap the end caps into the corre-
sponding holes in the hood (diagram 3).
NOTE: The end caps have been marked with “F”
and “R” for front and rear location indication.
WARNING: Small parts present a
choking hazard! Keep the four small end caps
away from children.
1
Cover Cap
Marks under End Caps
F
F
BB
2
3
F B
BF

16
12. POWER SUPPLY
CONNECTION
NOTE: The battery is disconnected for shipment
to prevent the battery from draining.
• Securely plug the battery connector into
the control module connector.
Control
Module
Connector
Battery
Connector
Battery
13. SEAT INSTALLATION
• Find Seat Back that marked “6” on its
back, also find the Seat Bottom marked
“7” on its back.
• Locate the Seat Back on the ground and
insert the Seat Bottom into the Seat Back
as shown.
NOTE: Gently insert the Seat Bottom tabs into
the corresponding Seat Back slots and push
to hear the Seat Bottom click into place. Once
the tabs clicks into place, it cannot be pulled
out without damaging the seat.
• Hook the clips (in the back of the seat) up
into the slots in the ride-on toy body, then
click the seat into the ride-on toy body.
• Tighten the seat with two M5x16 mm
machine screws.
ClipsClips
Seat Bottom
Seat Back
7
6
M5x 16 mm
Machine Screw

17
BATTERY CHARGING
IMPORTANT! Before first time use, charge the battery for at least 18 hours. Charge
the battery for at least 12 hours after each use of the ride-on toy. Never charge
the battery longer than 30 hours. Overcharging or undercharging the battery may
shorten battery life and decrease ride-on toy running time.
WARNING: Battery can fall out and injure a child if the ride-on toy tips over.
Always use battery cover.
PREVENT FIRE
• Never modify the electrical system.
• Alterations could cause a fire resulting in serious injury and could also ruin the
electrical system.
• Use of the wrong type battery or charger could cause a fire or explosion,
resulting in serious injury.
• Use of non-original components on this ride-on toy could cause overheating, fire
or explosion.
• The battery must be handled by adults only.
• The battery is heavy and contains sulfuric acid (electrolyte).
• Dropping the battery could result in serious injury.
• Never allow children to charge the battery.
• Battery charging must be done by adults only. A child could be injured by the
electricity involved in charging the battery.
• Never lift or carry the battery by the wires or connector, this can damage the
battery and possibly cause a fire resulting in serious injury. Lift and carry the
battery by the case only.
• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage
each time you charge the battery.
• If damage or excessive wear is detected, do not use the charger or the battery
until you have replaced the worn or damaged part.
CAUTION: Use the charger in dry locations only.
IMPORTANT NOTE
• We recommend that you start charging your battery before beginning assembly
of your new ride-on toy.
• The battery must be upright while charging.
• The charger is not a toy, and should only be operated by adults.
• Do not short-circuit the battery.
• You do not need to remove the battery from your ride-on toy to recharge it.
• Before charging the battery, examine the battery case for cracks and other
damage which may cause sulfuric acid (electrolyte) to leak during the charging
process. If damage is detected, do not charge the battery or use it in your ride-
on toy. Battery acid is very corrosive and can cause severe damage to surfaces
it contacts.

18
Charging Input
Socket
1
2
• Do not charge the battery on a surface (such as a kitchen counter top) which
could be damaged by the acid contained inside the battery. Take precautions to
protect the surface on which you charge your battery.
• Use only an original charger (AC 120V 60Hz) with an output of DC 24V (1A) to
charge your ride-on toy battery.
• NOTE TO ADULTS: Regularly examine the charger for damage to the cord, plug,
housing or other parts that may result in the risk of fire, electric shock or injury.
• If your battery is old and will not accept a charge, do not leave it in the ride-on toy.
Always remove a dead battery from the ride-on toy.
• After the first charge, recharge the battery for at least 12 hours after each use.
Never charge the battery longer than 30 hours. Charge the battery after each use,
regardless of how long the ride-on toy was used.
• Do not allow the battery to run down completely before charging.
• Charge the battery before storing the ride-on toy.
• Charge the battery at least once per month, even if the ride-on toy has not been used.
NOTE:
• This product has CHARGING PROTECTION: when charging, all the functions will
be cut off.
• Recharges after initial charge - Up to 12 hours, and never charge the battery
longer than 30 hours.
• When the ride-on toy begins to run slowly, recharge the battery.
• After each use or once a month minimum recharge time 12 hours, less than 30
hours at most.
CAUTION: Use the charger in dry locations only.
1. Plug the charger port into the input socket (the socket is under the seat).
2. Plug the charger plug into a wall outlet. The battery will begin charging.

23.0
19
HOW TO USE YOUR RIDE-ON TOY
Forward/Reverse Shift Lever
Sound Button
Foot Pedal
POWER SWITCH
• Turn the ride-on toy on or off.
FOOT PEDAL
• To move the car, press the foot pedal down.
• To stop, take your foot off the foot pedal.
FORWARD-REVERSE SHIFT LEVER
• To move the car forward at high speed, shift the lever to the “2” position.
• To move the car forward at low speed, shift the lever to the “1” position.
• To move the car backward, shift the lever to the “R” position.
NOTE: Use low speed until you get familiar with your new ride-on toy.
SOUND BUTTON
To activate sound, press the button on the steering wheel.
STOP
To stop the ride-on toy, you must take your foot off the pedal.
WARNING: The ride-on toy does not have brakes. Do not park or ride on any
slopes or steep inclines.
NOTE: For your safety, this ride-on toy has been designed with a one second delay start.
When the pedal is pressed, the ride-on toy will start to move one second later.
NOTE: Use low speed until you get familar with your new ride-on toy.
Power Switch
E