Dynamic CCTV DVR-8 User manual

Thank you for purchasing our product.
Please read this User s Manual before
using the product.
STAND-ALONE DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 Channel Digital Video Multiplex Recorder
VER 2.0
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 CH STAND-ALONE DVMR The most stable and reliable real stand-alone Digital Video Multiplex Recorder

ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITION & PROCESSING
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated “ dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnel only in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to
the unit whenever the power cord is inserted into the power source ; however, the unit
is operational only when the ON-OFF switch is in the ON position. The power cord is
the main power disconnect for all unites.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR 8 channel stand-alone DVMR

FCC INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received,
including interference that may cause undesired operation.
A CLASS A computing device subject to certification by the Commission shall be identified pursuant to
par.2.925 et Seq of the chapter. In addition, the label shall include the following statement:
Where a device is constructed in two or more sections connected by wires and marketed together, the
statement specified in this Section is required to be affixed only to the main control unit.
The users manual or instruction manual for the EUT shall contain the following statement or eqivalent.
Caution : Changes or Modifications not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
If the EUT requires accessories such as special shielded cables and/or connectors to enable compliance
with emission limits, the instruction manual for the EUT shall include appropriate instructions on the first
page of the text concerned with the installation of the device that these special accessories must be used
with the device. It is the responsibility of the user to use the needed special accessories supplied with the
equipment.
For a CLASS A digital device or peripheral, the instructions furnished the user shall include the following or
similar statement placed in a prominent location in the text of the manual.
Note : This equipment has been tested and found to comply with the limits for a CLASS a digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of the this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING

1
Chapter 1 . Product package
Chapter 2. Installation procedure
1-1. The contents of package 3
1-2. Name and function of each button (front panel) 4
1-3. Name and function of each button (rear panel) 5
2-1. Camera connection 6
2-2. Monitor connection (Composite monitor) 6
2-3. Monitor connection (S-VHS) 7
2-4. VCR & VIDEO PRINTER connection 7
2-5. Sensor connection 8
2-6. Network connection 8
2-7. HDD connection 9
2-8. Power connection 9
Chapter 3. Operation
3-1. DVR SYSTEM Log-in 10
3-2. Recording 11
3-3. Playback 14
3-4. Set-up 16
1. Basic operation 16
2. CAMERA SETUP 16
3. DISPLAY SETUP 17
4. TIME/DATE SETUP 19
5. RECORD SETUP 19
6. HDD MANAGEMENT 21
7. MISCELLANEOUS SETUP 21
8. TCP/IP SETUP 24
Chap 4. Specification and Configuration
4-1. SPECIFICATIONS 27
4-2. Configuration Stand-alone DVMR 28
4-3. RS-232C Hex-code table 28
4-4. Arrange of RS 485 and RS-232C pin 29
9. FACTORY DEFAULT 26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR Table of Contents
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8 channel stand-alone DVMR

Before reading this document
1. This document is intended for both the administrator and users of stand alone DVMR.
2. This manual contains information for configuring, managing and using stand alone DVMR properly.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture.
4. Be sure to read this manual before using stand alone DVMR Model, even before installing HDD.
8. For questions and technical assistance of this product, contact your local dealer.
About this document
2
Before installing stand alone DVMR, be sure to thoroughly review and follow the instructions in this
User’s Manual. Pay particular attention to the parts those are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow
THE instruction in manual for appropriate installation.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5. Check electricity at the place you want to install the DVMR unit is stable and meets our
electricity requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
6. Several chips on the main board of the DVMR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close
up an opening (fresh air in-take) on the right side of the unit..
7. Put the DVMR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-
in ventilation fan of the rack is properly running.
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
29
4-4. Arrangement RS-232C and RS-485 pin
# 2 RxD
# 3 TxD
# 5 GND
TxD # 3
GND # 5
RxD # 2
DVMR unit Other device (PC)
D-SUB 9 cable (twisted RS-232C cable)
Comm Port
RS-232C
1 5
6 9
Pin No. Definition
1NC
2RxD
3TxD
4SD-(RS 485)
5 GND
6SD+(RS 485)
7NC
8NC
9NC
Connection to PC using RS-232C cable
8 channel stand-alone DVMR 4. Configuration

Chapter 1 . Product Package
1-1. The contents of package
1. 8 ch stand-alone DVMR unit
Record data of pictures from camera on hard disk drive after converting it into digital data.
ALLABOUT IMAGE RECOGNIT ION & PROCESSING
Stand-alon e DVR
8 channel
Stand-alone DVR
Describe how to install and operate this DVMR unit.
4. DC power adapter and power cable
Convert AC 110V or AC 220V into DC 12V to supply to DVMR unit.
3. Remote controller
IR remote controller enables an user to operate DVMR unit apart from the unit.
3
2. User’s manual for 8 ch DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
OVERWRITE
RECORD
PLAY
SETUP ZOOM
MODE P/T PIP FRZ SEQPLAYMENU
1 2 3 4
8 channel stand-alone DVMR Product package
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
28
4-2. Configuration
4-3. RS-232C Hex-codes table
Following ASCII-code are for programmers who want to control DVMR unit via RS-232C port.
RS-232C specification (baud rate/parity/data length/stop bit) : 57600, N, 8, 1
1 Byte ASCII-code
8 channel stand-alone DVMR 4. Configuration
Camera #1~8
MODE
FRZ
SEQ
ZOOM
‘D’
‘F’
‘Q’
‘Z’
PIP
P/T
MENU
ENTER
‘I’
‘T’
CH1
CH2
CH3
CH4
‘1’
‘2’
‘3’
‘4’
CH5
CH6
CH7
CH8
‘5’
‘6’
‘7’
‘8’
UP
DN
LEFT
RIGHT
‘U’
H
K
J
‘M’
Sensor Alarm
Remote
Controller
TCP
/IP
TCP/IP
RS-232C Printer
P/T Camera RX Box VCR TV Monitor S-Video Monitor Video
Printer
POWER
ENTER
56 7 8

4
1. POWER SWITCH WITH LED : DC power switch with LED
Generally speaking, cutting power to system may cause trouble in DVMR
system or damage to HDD when HDD is in writing process, and we ask you to
press [MENU] button first to protect HDD from being damaged or system
failure before you press DC power switch off in practical operation.
2. MENU : Used to check or change parameters settings in SYSTEM SETUP. After pressing [MENU] button,
input password and press [ENTER] button to enter into SYSTEM SETUP.
3. PLAY/ENTER : Starts playback, and in some functions, it is used as the SELECT key.
Press shortly and it starts playback. If you press this button for a long time, you enter
into GO TO menu to start playback from image you want to start.
4. MODE : Changes screen division. Whenever you press [MODE] button, screen division is changed from
full screen to 4-split screen, 9-split screen in sequence, both in live or playback mode.
To change channel in full screen mode, just press number button.
If you press [MODE] button for a lone time, it changes type of monitor connected to DVMR unit
form COMPOSITE to VGA, or from VGA to COMPOSITE, in case VGA option is included in
DVMR system.
5. P/T : Manages PAN/TILT CONTROLLER. To control PTZ camera connected to DVMR unit, you have to
select model of PTZ camera in PAN TILE CMD SETUP/MISCELLANEOUS SETUP.
6. 1/5,2/6,3/7,4/8 : Chooses each indicated camera in full screen mode. Each button is double number
button, and pressing [1], [2], [3], and [4] for a very short time is for 1, 2, 3, and 4
respectively, and pressing [1], [2], [3], and [4] for a long time is for 5, 6, 7, and 8
respectively.
7. PIP : Assigns PIP (Picture In Picture)
8. FRZ : : Displayed screen is paused.
9. SEQ : To see display screen in rotation from channel number 1, 2, 3, and so on, both in live and playback
mode. It also change Quad screen from 1/2/3/4 to 5/6/7/8.
10987
6
5
4
3
212
11
10. ZOOM : Enlarges the display screen by 200%. Digital zooming.
11. Remote Controller Sensor Input Window
12. Direction button : [LEFT], [RIGHT], [UP] and [DOWN].
In playback mode, [LEFT] and [RIGHT] buttons are for selecting playback
direction(forward/backward), and [UP] and [DOWN] buttons are for increasing or
decreasing speed of playback.
NOTICE : If the Input window (IR receiver) is covered, the remote controller may not work.
NOTICE : If several buttons are simultaneously or incorrectly pressed, the system may not be operated unproperly.
1
POWER
ALL ABOUT IMAGE RECOGNITION & PROCESSING
13
13. LED Lamps : Represent status of operation. OVERWRITE/RECORD/PLAYBACK/SETUP.
8 channel stand-alone DVMR 1. Unit Description
ALL ABOUT IMAGE RECOGNITION & PROCESSING
ALL ABOUT IMAGE RECOGNITION & PROCESSING
27
4-1. SPECIFICATIONS
INPUT
OUTPUT
S/N RATIO
HORIZONTAL RESOLUTION
COLOR
ZOOM
PIP
SEQUENCE
SCREEN QUALITY
SPEED
MATERIAL
COMPRESSED PICTURE
PICTURE RECORDING
METHOD
REC, MODE
TRACK PLAY
SPLIT SCREEN
WEB INTERFACE
POST ALARM FUNCTION
BACK-UP
OTHERS
CAMERA CONTROL
HDD
CD-RW BACK-UP
8 CH INPUT 1.0 VP-P, 75 OHM UNBALANCED (BNC TYPE)
3 OUTPUT VBS : 1.0VP~P.75 OHM UNBALANCED (BNC TYPE)
MORE THAN 4dB
480TV LINES
16.7 MILLION
LIVE & PB AVAILABLE
AVAILABLE
AVAILABLE
FULL : 720(H)X480(V) ACTIVE PIXELS
1/4 SCREEN : 360(H)X240(V) ACTIVE PIXELS
0.1~30 FRAME/SEC (EACH CHANNEL)
HDD
JPEG
FIELD SWITCHER METHOD FULL SCREEN RECORDING
REAL-TIME/ TIME-LAPSE / EVENT
SEARCH, STILL
FULL, QUAD DISPLAY. 9-SPLIT
Stand alone DVMR
TCP/IP with client software
1~59SEC, CONTINUOUS TIMING ESTABLISHMENT POSSIBILITY
CONVENTIONAL VCR, TIME LAPS VCR (VCR OUTPUT PROVIDED)
REMOTE BACK-UP USING TCP/IP
INTERNAL BACK-UP(MARK IMAGE)
RS232C, RS485, 8 ALARM INPUT
PAN/TILT/ZOOM AND FOCUS
REMOTE CONTROL : EXTERNAL EQUIPMENT, WIPER,PUMP,FAN AND
HEATER
INTERNAL 1 HDD
CD-RW DRIVE
CD-R MEDIA
VIDEO I/F
MONITORING
METHOD
RECORDING
/PLAY
FUNCTION
OTHER
FUNCTION
MODEL NO
OPERATION TEMPERATURE
OPERATION HUMIDITY
IR REMOTE CONTROLLER
DIMENSION
WEIGHT
POWER SUPPLY
41F~ 104F (5C~ +40C)
LESS THAN 90%
BUILT-IN
19 INCHES IN WIDTH , 1.5U 434 mm x 360 mm x 66 mm
APPROX. 4.8KGs (WITHOUT HDD)
DC ADAPTER (12V DC 5A)
MECHANICAL
8 channel stand-alone DVMR 4. Configuration
1-2. Name and function each button (front panel)
Chapter 4 . Specification and configuration
MENU PLAY MODE P/T PIP FRZ SEQ ZOOM
1234
OVERWRITE
RECORD
PLAY
SETUP ENTER
56 7 8

5
5. LOOP Output
6. VCR Connection
7. MONITOR Connection
8. VGA Connection
10. D/C Power Connection
3. LAN (TCP/IP)
2. Sensor Input/Output
1. RS-232C and RS-485 port Connection
4. Camera Connection
9. S-VHS Connection
NOTICE : When connecting with other applications, be sure to turn off the system.
1
4
2
3
6
7
8
910
ALL ABOUT IMAGE RECOGNITION & PROCESSING
5
DC 12V
VCR
CH1 CH2 CH3 CH4
MONITOR
LOOP
V
G
A
ALARM/ RELAY
CH5 CH6 CH7 CH8
ETHERNET
Com m Port
RS-232C/485
S-VHS
8 channel stand-alone DVMR 1. Unit Description
26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
9. FACTORY DEFAULT
Press [ENTER] button when half-tone green bar is in on
FACTORY DEFAULT.
FACTORY DEFAULT
ALL SETUP
CAMERA COLOR
CAMERA TITLE
MOTION MASK
PAN/TILE COMMAND
SYSTEM STATUS
RUN
HDD MANAGEMENT
1) CAMERA COLOR SELECT , EDIT ENTER /
FACTORY DEFAULT is parameters setting done just
before delivery by manufacturer, and manufacturer
recommend our users to use DVMR unit with settings
done by manufacturer until our users become to have full
understanding about DVMR system.
FACTORY DEFAULT can be set group by group or as a
whole at once.
Parameter settings about color of camera like brightness,
contrast and others of camera. If we set CAMERA COLOR
at YES, all changes you made in ADJUST COLOR/
CAMERA SETUP shall be deleted and return to settings
done by manufacturer before delivery.
2) CAMERA TITLE
Default camera title is CH-01, CH-02, and so on.
3) MOTION MASK
Motion mask is for motion detection area, motion window, and sensitivity.
If we set MOTION MASK at YES, all changes you made in MOTION SETUP/CAMERA SETUP shall
be deleted and return to settings originally done by manufacturer.
4) PAN/TILT COMMAND
As explained in PAN/TILT COM SETUP/MISCELLANUOUS SETUP, this DVMR system includes
built-in protocol models like PELCO D type and we can select model of PTZ camera connected to
DVMR unit.
In case PTZ camera you are going to connect to DVMR unit is not one of models whose protocol is
already incorporated into DVMR system, you can input protocol of PTZ camera in USER DEFINE
mode/PAN TILT SMD SETUP menu.
Even though you set PAN/TILT COMMAND at YES, built-in protocol remain unchaged
However, protocol you input in USER DEFINE model is deleted if you set PAN/TILT COMMAND at
YES and set at FACTORY DEFAULT. Be careful not to set at YES to keep protocol you input as a
USER DEFINE model.
5) SYSTEM STATUS
It is setting related recording parameters like recording speed, IP address, and others related to
system. If you set SYSTEM STATUS at YES and set at FACTORY DEFAULT, you have to set
recording speed, and input IP address and others again.
6) ALL SETUP
If you set ALL SETUP at YES and set at FACTORY DEFAULT, all groups of FACTORY DEFAULT are
initialized. That is, all parameter settings is done again just as done by manufacturer before deliverly.
---
NO
NO
NO
NO
NO
8 channel stand-alone DVMR 3. Operation
1-3. Name and function each button (Rear panel)

2-1. Camera Connection
Connect the camera to the CAMERA INPUT on the Rear Panel of the system.
2-2. Monitor Connection (Composite Connection Method)
Connect the monitor to the MONITOR OUT on the Rear Panel of the system
6
VIDEO
LENS VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear part of CAMERA
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
Notice : Connect camera or monitor to DVMR unit while DC power switch on the front panel is off.
Setting video system : The DVMR set the video system of camera NTSC or PAL automatically.
Screen positioning : If picture displayed in your monitor is not at the center of monitor, you can relocate
images to make them shown in the middle of monitor.
Press [P/T] button for a long time to enter into screen position mode, and you
can adjust location of pictures using [UP], [DOWN], [LEFT] and [RIGHT]
buttons. Press [P/T] button for a long time again to quit screen positioning mode.
If you press [ENTER] button in the process of screen positioning mode, location
of pictures return to original location set by manufacturer.
VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
8 channel stand-alone DVMR 2. Installation
25
ALL ABOUT IMAGE RECOGNITION & PROCESSING
3) Example of Port Forwarding
Because ADSL is the most popular Internet service widely available in most of countries, we explain
more details about how to connect DVMR unit to ADSL line via Router or Gateway, to allow
accessing to this DVMR unit via Internet line far apart from DVMR unit.
InternetPC
Client program
(remote viewer)
ADSL
modem
w/
dynamic IP
or
static IP
DVMR unit-1
Router
or
Gateway
PPPoE
protocol
Port Forwarding
(IP Forwarding)
DVMR unit-5
DVMR unit-4
DVMR unit-3
DVMR unit-2
Other
device(PC)
211.100.16.8
IP : 192.168.1.150
PORT : 8000
IP : 192.168.1.151
PORT : 8001
IP : 192.168.1.152
PORT : 8002
IP : 192.168.1.153
PORT : 8003
IP : 192.168.1.154
PORT : 8004
IP : 192.168.1.165
PORT : 8015
Intranet
Port forwarding : Port forwarding is called differently by each of router manufacturers, like IP forwarding,
IP bounding, port forwarding, port bounding or port routing. Our users can set port forwarding stated in
installation manual of router or gateway without big trouble, and complete IP network to which user can
connect many of our DVMRs, that are 1 ch DVMR, 4 ch DVMR, 8 ch DVMR and 16 ch DVMR, to access
to those units via Internet line far apart from those units.
Port forwarding is a kind of arrangement we have to set in web site of Router or Gateway to connect
external port to internal IP address, for example in above picture, PORT 8000 to IP 192.168.1.150,
PORT 8001 to IP 192.168.1.151, an so on.
According to our own test with NETGEAR Router, it is working perfectly, and we recommend our users
to adopt NETGEAR Router in case DVMR unit is connected to ADSL line.
PORT
From 8000
To 8015
8 channel stand-alone DVMR 3. Operation
Chapter 2. Procedure

VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
VCR
CH1 …... CH8
MONITOR
LOOP
V
G
A
2-3. Monitor (S-VHS) Connection
Connect S-VIDEO Monitor to MONITOR OUT(S-VHS) on the Rear Panel of the system.
2-4. VCR & VIDEO PRINTER Connection
Connect VCR or VIDEO PRINTER to VCR OUT on the Rear Panel of the system.
7
VIDEO
A
IN OUT
VIDEO
C
IN OUT
VIDEO
B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
VIDEO PRINTER
VCR
8 channel stand-alone DVMR 2. Installation
24
ALL ABOUT IMAGE RECOGNITION & PROCESSING
8. TCP/IP SETUP
Press [ENTER] button when half-tone green bar is on
TCP/IP SETUP.
TCP/IP SETUP
MAC ADDR . . . 00-01-A2-01-1E-77
IP ADDRESS
IP PORT
SUBNET MASK
GATEWAY
DHCP SETUP
TCP/IP SETUP
SELECT , THEN ENTER
TCP/IP setup must be done correctly to access to DVMR
unit via IP network from client PC far apart from DVMR
unit.
MAC ADDRESS is not allowed for users to change and it
is very unique number assigned by manufacturer as per
IEEE regulation.
IP ADDRESS, IP PORT, SUBNET MASK, and GATEWAY
are what users must input manually, or our DVMR can get
those data automatically in case DVMR unit is connected
directly to DHCP server in IP network.
To input each element of IP data, move small triangular
cursor to the item you want to change, and press [ENTER]
button, then you can change using [UP]/[DOWN] and
[LEFT]/[RIGHT] button.
1) Concept of accessing to DVMR unit via IP network
PC DVMR unit PTZ
Camera
LAN, WAN, or Internet
Client program
(remote viewer) TCP/IP setup
2) Conditions of IP network
a) Accessing to DVMR unit in the same Intranet(LAN)
DHCP server
Router/Gateway
IP Sharer DVMR unit
PC
LAN
b) Accessing to DVMR unit via Internet line
InternetPC
Leased line : Manual
Cable modem : Automatic
Leased line w/ static IP
Cable modem w/ dynamic IP DVMR unit
Client program
(remote viewer)
InternetPC
ADSL
modem
w/
dynamic IP
or
static IP
DVMR unit
Client program
(remote viewer)
Router
or
Gateway
PPPoE
protocol Port Forwarding
(IP Forwarding)
Manual
For more details of TCP/IP setting in DVMR unit and PC, refer to “Remote Viewer manual”.
DHCP SETUP
DHCP SETUP
DHCP SETUP
Automatic
Other devices
: 192. 168. 1. 171
: 8000
: 255. 255. 255. 0
: 192. 168 . 1. 1
: MANUAL
8 channel stand-alone DVMR 3. Operation