The Inflator is equipped with a permanently lubricated, maintenance free motor. Can be run
continuously up to 30 minutes. Allow unit to cool for 20 minutes between uses. The motor is
fan cooled, a unique feature for such a compact Inflator.
Never try to lubricate the compressor. All maintenance and repairs must be performed by
Dynaplug to maintain the Limited Warranty during the warranty period. Always contact
dynaplug.com with your questions.
1. Remove cap from valve stem and attach zero-loss connector.
2. Screw on (clockwise) zero-loss connector firmly, “finger tight” so no air is leaking.
3. Plug power cord into cigarette lighter receptacle or SAE connector (or optional accessories).
4. LED work light and backlit pressure gauge automatically illuminate.
5. Press compressor power switch to ON position to start compressor.
6. When pressure gauge reaches desired pressure, press switch OFF.
7. Disconnect power plug; rapidly unscrew connector (counter clockwise) from valve stem to
virtually eliminate air loss.
Inflator can run on a vehicle battery source while vehicle is running or not running;
however, inflation will be slightly faster if vehicle is running.
Inflatables (balls, air mattresses, etc.)
1. Attach appropriate needle or nozzle to zero-loss connector.
2. Insert needle or nozzle into inflatable item.
TIP: Wet the needle with a little saliva for easier insertion.
3. Plug power cord into cigarette lighter socket or SAE plug (or optional accessories).
4. Press switch to ON position.
5. Press switch OFF when proper inflation is completed.
Hardwired power cord with SAE
connector and SAE to combo
Cig/BMW*-style lighter plug
together extend 9.84’/3m long.
*European-style
The first Polarity Protection, integrated circuit
in a 12VDC Inflator protects
Inflator from
damage if there’s a reversed polarity hook up to
a battery. The red LED on front of case
illuminates as a WARNING when a reversed
polarity hook-up is detected. Simply reverse
the connections to correct polarity and proceed
Easy-to-read, precision linear pressure gauge eliminates the
need to purchase or carry a separate tire pressure gauge.
Blue LED backlighting insures the gauge is easy-to-read during
low light or nighttime use. The illumination is automatic when
Inflator power cord is plugged in. The gauge reads in PSI and
BAR.
Patented Technology Pressure Gauge
Three interior compartments store: coiled air
hose, power cords and sports inflators (3) for
convenient access whenever needed.
High efficiency, built-in LED work light for low light and nighttime
conditions. This feature automatically illuminates when Inflator
power cord is plugged in.
Zero Loss Inflation Valve Stem Connector
separate zippered compartments:
one for Inflator and one for
Dynaplug® tire repair tools or
Battery clips to SAE plug pigtail cord with
inline 15AMP fuse housing with dust cap.
Ring terminal to SAE plug pigtail cord with
inline 15AMP fuse and dust cap for fuse holder
and for SAE plug. Cord installs on vehicle
battery for convenient use. 19.7”/0.5m long
Made of solid brass, this connector screws “clockwise” on the
valve steam with zero air leaks. This is particularly important for
achieving the tire pressure desired when you remove the
connector. Some lever-type style connectors do not seal well
and can lose 5-10 psi in a matter of seconds. This is particularly
important for motorcycle, scooter, bicycle and other smaller tires.
Three ways to reach us: www.dynaplug.com 1.530.345.8000 dynaplug@ustcmail.com
Your satisfaction is our goal. Our service is fast and reliable. We
have engineers on staff to answer your technical questions. We
respond to questions by email within 24 hours. Need faster
service, feel free to contact us by phone.
TIP: Turn the air hose
coil counter clockwise
while pushing it into the
storage compartment.
Important: Inflator can run continuously for 30 minutes, but then must cool for 20 minutes
before re-use.
The bayonet locking
red tip insulator on
the plug is removed
for BMW-style
socket use.
