Dyness A48100 User manual

Dyness A48100 battery and SOLIS Setup
Check List:
All of DYNESS battery has same DIP settings and cable
connections,here are examples of A48100 and Powerbox Pro;
Power cables;
Parallel cables;
Communication cable between battery and inverter;
Communication cables between battery and battery;
RHI-6K-48ES-5G
Before starting, make sure battery and inverter size matched.
Follow Dyness user manual to check details, it is recommended to
use battery in 1: 2 configuration at least.
Step 1 : Cable connect in inverter
Keep both inverter and battery completely off.
Connect power cable and comm cable to inverter firstly.
1.1 AC terminal wiring of inverter: connect the power grid and load
to ac-grid and ac-backup terminals of inverter respectively.
1.2 PV input wiring of inverter: insert the positive and negative
poles of PV into the positive and negative poles of DC port of
inverter respectively

1.3 Meter wiring: meter interfaces 1 and 4 are connected to power
grid L and N respectively; 5. 6 connected to CT; Connect the
power meter RS485 to the inverter RS-485 meter interface through
the network cable in the accessories; The CT is clamped on the
live wire of the power grid (pointing to the direction of the power
grid)
It’s normal standard pin-pin cable between battery and
inverter ,also battery and battery.

No matter how many inverters and how many batteries are in
parallel,it is always the master battery communicates to the master
inverter.
1.Dyness A48100 connect with Inverter
INV-BAT: From the master CAN IN to the
inverter CAN port;
BAT-BAT: From the master CAN OUT to the
salve1 CAN IN, the salve1 can OUT to the
salve2 CAN IN...
M
aster 0010
Salve
00
0
0

2.Dyness Powerbox Pro connect with Inverter
The master factory default is 0010,so no need open the cover to change
anything,use it directly.
If only one Powerbox Pro ,it is the master itself.
Master box
INV-BAT: From the master box CAN IN to
the inverter CAN port;
BAT-BAT: From the master box CAN OUT
to the salve1 box CAN IN, the salve1 box
CAN OUT to the salve2 box CAN IN...
Slave battery
ADD:0000
Master battery
ADD:0010

The slaves need to open their cover to change inside 1# module to 0000.
Step 2:Switch on battery
Turn on all the batteries ON/OFF switch,long press 3s master SW
to turn on all batteries.
When its loose like Powerbox Pro,long press 3s power switch on
Powerbox Pro to power on battery.
Step 3 : Breaker/Fuse between inverter and battery
Connect DC breaker or Fuse between inverter and battery to protect
both products.Turn on it after switching on batteries.Surely if it is
Powerbox Pro or Powerdepot,you can turn on itself DC breaker on
the side of box.
Step 4: Setup inverter
Now inverter is started,we can do some setup on the inverter to
make the communication success.
Salves box
Slave battery
ADD:0000

Step 5: Battery type setting
1. ENTER→Advanced Settings→Advanced Settings→Password：
0010 →Storage Energy Set →Battery Select →Dyness LV →
ENTER→ENTER→ESC→Save & Send

Step 6: Work mode setting
The inverter has four working modes: Self use, Feed in priority, Back
up and off grid mode. Note: when setting each mode, other modes
must be closed.
After setting the working mode, the inverter can work normally
Step7:Make the inverter start charging battery to 100% to
calibrate SOC.
Step 8: Shut Down
POWEBOX
1 Remove all the load
2 Turn off DC breaker of Powerbox Pro.
3 Long press 3s Reset button of the master Powerbox Pro to turn
off it,slaves will be controlled to turn off automatically.

4 Disconnect PV/Grid
5 Turn off the inverter power switch,shut down the inverter
Modules Parallel
1 Remove all the load
2 Turn off DC breaker between the battery and inverter.
3 Disconnect PV/Grid
4 Turn off the inverter power switch,shut down the inverter
5 Long press the master module SW button to turn off all the
batteries,then switch off all the batteries’ ON/OFF switch.