Dyson Airblade Tap User manual

The Dyson Airblade Tap hand dryer should be cleaned daily.
Follow these 3 simple steps to ensure the machine performs
to its best and remains hygienic.
Keep it clean
Important information
Most professional cleaning chemicals
can be used. The following are some
that are harmful to the machine.
Using the wrong cleaning method or
product may invalidate the warranty.
All cleaning chemicals should be used
exactly as indicated by the manufacturer’s
instructions (including appropriate dilution).
Any chemicals intended for use should
first be tested on an inconspicuous area
to confirm suitability. Aside from cleaning
chemicals, care should be taken to avoid
any harmful fluids from coming into contact
with the product, in particular oils and
alcohol-based products.
Do not pressure wash the machine.
Water supply cleanliness
and biological growth
In some countries there are regulations
or guidelines that require temperature
controlled water supply systems (such as
that supplied to the Dyson Airblade Tap
hand dryer) to be subjected to regular
cleaning to minimise any biological growth.
To enable you to meet these regulations,
the Dyson Airblade Tap hand dryer has
been designed and tested to withstand
internal cleaning both with hot water up
to 95°C and with sodium hypochlorite
at a concentration of 0.45%.
When carrying out internal cleaning of the
Dyson Airblade Tap hand dryer, please be
aware of any safety considerations when
using hot water or chemicals. Dyson will
not be responsible for any injury caused
by this process.
Dyson is unable to advise regarding the details
of the cleaning you should carry out because
this will be specific both to the applicable
regulations and to your water supply system.
Contact us for more information:
0800 345 7788
[e-mail]
www.dysonairblade.co.uk
Alcohol-acid mixes
Alcohol
Solvent/oil-based mixes
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners
DO NOT USE:
Wipe sensors using a soft
cloth and non-abrasive
cleaner then place
cleaning cap over sensors
to prevent activation.
Clean all tap surfaces,
sink, mirror and any walls or
counter tops. When complete
REMEMBER to remove
cleaning cap.
REGULARLY clean air inlets
on base of motor bucket
(under sink). Ensure plughole
in sink is free from blockages
so water can drain freely.
1 2 3
JN: 70759 17.11.14

The Dyson Airblade V hand dryer should be cleaned daily.
Follow these 3 simple steps to ensure the machine performs
to its best and remains hygienic. Using the wrong cleaning
method or product may invalidate the warranty.
Keep it clean
Wipe all surfaces with a soft
and non-abrasive cleaner,
including the air inlets on
the side of the machine.
Clean the wall underneath
the machine. This may be
required more regularly
in high use areas.
Clean the floor beneath
and around the machine.
1 2 3
JN: 70758 17.11.14
Important information
Do not pressure wash the machine.
All cleaning chemicals should be used
exactly as indicated by the manufacturer’s
instructions (including appropriate dilution).
If a cleaning product is left on the machine for
too long, a film will form. This may reduce the
effectiveness of the antibacterial additive.
Any chemicals intended for use should
first be tested on an inconspicuous
area to confirm suitability. Aside from
cleaning chemicals, care should be taken
to avoid any harmful fluids from coming
into contact with the product, in particular
oils and alcohol-based products.
Chemical guidelines
Most professional cleaning chemicals
can be used. The following are some
that are harmful to the machine.
Filter change kit
Designed for machines with high usage,
the kit provides everything needed to
change the machine’s HEPA filter on site.
Contact us for more information:
0800 345 7788
[e-mail]
www.dysonairblade.co.uk
Alcohol-acid mixes
Alcohol
Solvent/oil-based
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners
DO NOT USE:

The Dyson Airblade dB hand dryer should be cleaned daily.
Follow these 3 simple steps to ensure the machine performs
to its best and remains hygienic. Using the wrong cleaning
method or product may invalidate the warranty.
Keep it clean
Important information
Do not pressure wash the machine.
All cleaning chemicals should be used
exactly as indicated by the manufacturer’s
instructions (including appropriate dilution).
If a cleaning product is left on the machine for
too long, a film will form. This may reduce the
effectiveness of the antibacterial additive.
Any chemicals intended for use should
first be tested on an inconspicuous
area to confirm suitability. Aside from
cleaning chemicals, care should be taken
to avoid any harmful fluids from coming
into contact with the product, in particular
oils and alcohol-based products.
Chemical guidelines
Most professional cleaning chemicals
can be used. The following are some
that are harmful to the machine.
Filter change kit
Designed for machines with high usage,
the kit provides everything needed to
change the machine’s HEPA filter on site.
Contact us for more information:
0800 345 7788
[e-mail]
www.dysonairblade.co.uk
Alcohol-acid mixes
Alcohol
Solvent/oil-based
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners
DO NOT USE:
Wipe all surfaces with a
soft cloth and non-abrasive
cleaner. Particular attention
should be paid to the seals
and sides of the machine.
Clean the air inlet on
the base REGULARLY.
Clean the floor beneath
and around the machine.
This may be required more
regularly in high use areas.
1 2 3
JN: 70757 17.11.14