EAGLE GOLF X4 User manual

Page%1%of%6%
EAGLE GOLF
TROLLEY X4/X5
USER MANUAL
With lithium battery
MOST IMPORTANT THINGS TO KNOW BEFORE USING
THE EAGLE GOLF TROLLEY X4/X5……………………….....2
CHARGING AND CARE OF THEBATTERY…………………..2
INSTALLING THE BATTERY……………………………………3
ASSEMBLING/DISASSEMBLING ……………………………..4
SPEED CONTROL FEATURE……………………………….….5
ALIGNMENT SYSTEM……………… …………………………..6

Page%2%of%6%
MOST IMPORTANT POINTS TO READ BEFORE USING THE EAGLE GOLF TROLLEY X4/X5
a. Charge the battery
b. Assemble Swift by connecting the handle and chassis together [see point 4]
CHARGING AND CARE OF THE BATTERY
Before the first use and after each use, charge the battery. The battery and charger
come with an easy connection system.
Important: - Before using the battery for the first time, it must be charged overnight.
a. Recharge the battery as soon as possible after each use, regardless of the
duration of use. The battery will charge best when it is flat, in a warm and well-
ventilated location. Note: It is recommended to avoid charging on a concrete
floor in winter and to charge in a warm area of the house instead.
b. Minimize battery drain during play by avoiding taking the Swift into rough terrain
whenever possible.
c. Avoid using the Swift to pull you up hills as much as possible.
d. In between uses, it is recommended to keep the charger connected to the
battery with the power on, rather than disconnecting it.
e. If you will not be using the golf trolley for an extended period of time, it's okay to
disconnect the battery once it is charged. However, it is important to note that the
battery should be recharged at least every 3 months, and before use.
f. The battery is designed to be a sealed unit, but it is still recommended to check
with the airline prior to travel if you plan on taking the golf trolley and battery on a
flight
g. To avoid damaging the battery, take care when handling it and be careful not to
drop it. The battery casing is delicate and can be easily cracked, which will
negatively impact the battery's life.

Page%3%of%6%
Battery
connector in
handle
FITTING THE BATTERY
To fit the charged battery to the Eagle Golf Trolley X4/X5:
a. Connect the battery to the extended cables and place it in the
pocket of the golf bag.
b. Connect the battery cables to the battery connector in the handle.
c. When the battery is properly connected, the LED button light should
turn on and flicker slowly.

Page%4%of%6%
ASSEMBLING GOLF TROLLEY
a. Wheel Assembly
a.1 make sure direction of arrowhead in tire is face to the front. Then can distinguish
left wheel and right wheel.
a.2 Press the quick release button on the rear wheel and insert the axle.
a.3 Ensure that the four knobs on the inside of the wheel are aligned with the
corresponding four on the drive dog on the axle.
When the wheel is securely locked, there should be an audible clicking sound.
b. Free Wheel Mode
The Eagle Golf Trolley X4/X5 features a freewheeling gear system. In the event that the
trolley stops functioning during a round of golf, it can easily be pushed forward in
freewheeling mode.
It is important to note that as a freewheeling golf trolley, the trolley should be positioned to
prevent it from rolling forward when stopped. Both the X4 and X5 models have been
designed to not roll backwards easily.
b1. Hold the release button and slightly pull the wheel out to allow the four knobs on the
wheel to disengage from the drive dock on the axle.
b2. Release the button, rotate the wheel to ensure that it can rotate freely on the axle
Assembling golf trolley c1. Pull the fold handle upward. c2 single push-fit connection

Page%5%of%6%
B: button A: potentiometer
SPEED CONTROL FEATURE
1. Plug in the battery with the potentiometer at the 0 point. The LED will flash quickly
once, then flash slowly once, and continue. The cart is now in the braking condition.
2. Start: When the cart is in the braking condition, press and release the button to end
the braking condition. Then, the speed can be adjusted using the potentiometer. The
LED will be solid.
3
. Plug in the battery when the potentiometer is not at the 0 point. The LED will flash
quickly, indicating that the cart is not in the braking condition.
4. Start: Turn the potentiometer back to the 0 point to adjust the speed. The LED will be
solid.
5 . Stop: When the cart is moving forward, press and release the button to stop the cart.
The cart is now in standby mode and the LED is solid.
6. Stop: When the cart is moving forward, decrease the speed by turning the
potentiometer back to the 0 point. The LED will flash quickly once, then flash slowly
once, and continue. The cart is now in the braking condition.
7. When the cart is in the braking condition, press and release the button to end the
braking condition. The LED will be solid.
8. Press and release the button to activate the braking again.
9. When the cart is in standby mode, press and hold the button until the LED flashes
quickly. Release the button, and the cart will move forward for 10 seconds and stop
automatically. This is the DCF .

Page%6%of%6%
ALIGMENT SYSTEM
When golf trolley is not going straight, we have to adjust the location of front axle
1.Loosen the big nut on the front wheels.
2. Loosen the bolt and tighten the bolt on the opposite side.
3. Tighten the big nut to complete the alignment.