Eaglemaster E4 User manual

PASS

About Your System
NOTE:
Congratulations on yourpurchase of thisstate-of-the-art vehicle securitysystem.
With proper installationthis system willprovide superior protectionand performance for
many years tocome.
What is included:
Acontrol module
2-way pager transceiverantenna
One 5-button 2-wayLCD remote transmitter
One 3-button or4-button random coderemote transmitter
Dual stage shocksensor
High output 6-tonesiren (optional)
Status LED indicator
Valet over-rideswitch
Options and Accessories:
This system includesseveral optional inputsand outputs allowing the creation of a
completely personalized securityand convenience system by offering manyoptional
features such as:
2nd stage doorunlock
Horn honk output
2pulse signal doorunlock
Engine turbo timemode
Check range notification
Arm/disarm chirpon/off
*Many require additionalparts and/or labor, see store for details
Some of thefeatures described in this manual may required additional parts and/or
labor, andmay not be included as part of the standard installation of this unit.
Additionally, manyfeatures of thissecurity system have selectable options that must be
activated or programmedduring the system's installation. These itemswill be identified
in the followingsections. Please discuss these features and any questions you may
regarding the installationof this product with your authorized dealer.
Window close control
Anti car-jack bydoor switch
Power trunk/hatch release
Glass breakage sensor
Micro-wave detector
Back-up battery sirem
-3-

NO.TR-57
2-way LCD Remote Transmitter Description
System maintenance
This system needsno specific maintenancebeyond 2-wayremote controlbattery
replacement. The 2-wayremote is poweredby a 1.5VAAA battery.
Low Battery Notification
If the batterybecomes exhausted, theremote will emitextra long beep,and indication
the melody (samemelody while batteryon ). Whilepress any buttonon the remote, few
seconds later the indicator will flashingfor identify.
Battery Replacement
Gently pull theend of thebattery door awayfrom the top of the remote control then
slide the doorup to exposethe battery andremove the expired battery. Placethe new
battery into theremote control observingthe correct polarity. When poweris returned
the remote controlwill light allicons and generatemelodies (representing all beeper
tones).
#TX-4R
Functions of remotetransmitterbuttons
Button to armthe system (ARM)
Button to disarmthe system (DISARM)
Button to controlTRUNK Programmed channel
Button to checkcar status , to turn on LCD back light
Button to Silentarm the system (SILENT)
PASS

Remote Function Table:
Functions Step Condition
Arm and door lock
Arm without siren chirp
Disarm and door unlock
Disarm without siren chirp
Trunk open
Anti car-jack mode
Panic mode
Car search mode
1st stage sensor bypass
2nd stage sensor bypass
Valet mode
Status check & Back light
Remote button 1.2.3 on/off
Silent arm mode
Enable check-in range
Vibrate mode on/off
Disable remote receiving
Time adjust mode
Press once
Press once then within 3sec. press once
Press once
Press once then within 3sec. press once
Press over 2sec
Press together over 2sec..
Press over 2sec.
Press once after 8sec. of armed
Press once within 8sec. of armed
Press once within 8sec. of armed
Press together over 2sec.
Press once
Press .
Press once.
Press once within 8sec. of armed.
Press
Press together over 2sec.
Press together over 3sec.
together over 2sec.
together over 2sec.
Disarmed & ACC off
Disarmed & ACC off
Armed
Armed
Any time
ACC ON
Armed
Armed
Armed
Armed
ACC ON
Disarmed
Armed

Standard LCD 2-way icon instructions
LCD Display
CAUTION:
Use of thissystem is for car start andalarm
purpose only.
Since this systemis a precise instrument that is fragile and
susceptible to damagefrom external shock, do not drop the
unit, and keepit away from children. Do not keep the remote
near excessive humidityor water, as it is not water proof.
PASS
LCD Icon LCD Function
Transmitted/Transmitting icon
Door lock (Arm)
Door unlock (Disarm)
Panic mode /Alarm Triggering
Hood open
Door open
Trunk open

LCD Icon LCD Function
1st sensor trigger
2nd sensor trigger
sensor bypass
immobilizer mode
Ignition switch
Silent mode
Valet mode
Anti car-jack mode
Auto re-arming
Call mode
Colock
Remote button lock
PASS

LCD Icon LCD Function
Vibration mode
Battery Meter
Battery conserve mode(disable receiving)
Engine running /
Colock time start(optional)
Fix time start(optional)
Temperaturestart (optional)
Safety mode (optional)
Turbo mode

Disable remote receiving
You may turn offthe 2-Way remote receiving signalfrom the mainunit. Press button
simultaneously for 2sec.until one longbeep is heard.Remote receiving isnow
disabled. To turn onreceiving again, Pressbutton simultaneously untiltwo long
beep is heard,remote receiving isnow enable.
2way remote button ON/OFF
For safety purpose,this 2-way remote can be lockout the remote button in order notto
mis-touched the buttons.Press button forover 2sec. until one beep is heard,
remote button isnow locked. To turn onremote button, press button for over 2sec.
until two beepsis heard, remote button is now unlocked.
Programming 2-way remote
2-way LCD display:
2-way LCD display:
If set withvibration only
the 2-way LCDwill display :
Vibrate mode on/off
Press button forover 2sec. the 2-way remote willrespond tone &vibrate feature,
the button pressing2sec. will change the feature, seeunder table:
Beeps 2-way remote feature
Vibrations
1-beep
1-beep
1-time
1-time
Remote with toneand vibration
Remote with vibrationonly
Remote with toneonly

Time adjust mode
Besides operating foralarm functions, LCDremote control additionallyprovides 12-hour
clock, alarm clock.
Instructions:
1. Press and holdButton for 3sec.to enter time-setup mode, 1 beep will be heard.
2. Press button toselect Hour &Min adjust setting.Icon flashing toindicate.
3. Press button toturn up thenumbers. Press button to turn downthe numbers.
The button maybe held down to scroll faster.
4. Press button toexit the settingmode. 2 beepwill be heard.
Note: The remote willrevert to normaloperation from theset mode when 10-seconds has
elapsed without abutton entry.
Minutes display
24-hour display

Display Beeps Vibrations Trigger
1st stage-Sensor warning
2nd stage-Sensor triggering
Trunk switch triggering
Door switch triggering
Hood switch triggering
Ignition triggering
5 short
Melody 1
Melody 2
Melody 3
Melody 4
Melody 5
1 times
1 times periodically
2
5 times periodically
times periodically
3 times periodically
4 times periodically
2-way signal paging features
A pageis the signalthe control modulesends to the remote controls confirmation of
receipt of acommand or alarmsystem status. Whenthe remote controlreceives a page
it will generatea page notificationto the user(notifications are audiblebeeps) and the
LCD Icons willdisplay the currentsystem status.
Command Page
When a command(arm/disarm, or auxiliarychannel) from theremote control issent
and received, thesystem will senda command pageback to confirmreceipt.
Alarm Page
If the alarmsystem is triggered while armed, an Alarm Page will be sentto the remote
control. When theremote receives an Alarm Page, the LCD icons will display the alarm
system status informationand the remote control will generate beeps.
Page Recognition (Acknowledgement)
Toclear a pagealert/notification, quickly pressany button onthe remote control.This
can be performedat any timeduring or afterthe page notificationhas occurred.
The remote controlwill not senda command tothe system atthis time; itwill only clear
future repeats ofthe page notification.The next timea button ispressed on the remote
control it willsend a commandto the system.

Check-in range notification(on/off )
Arming the systemwithin 8-seconds, pressbutton once onthe 2way remote, the
system will enablethis Check- inrange function.
- With in5 minutes, the2-way remote willthan give 1 beep sound every one minute for 5
cycles to remindthe user withinrange.
- After5 minutes ,the Antennaicon will indicates under receiving status:
For friendly usage,the 2-way remotewill provide 2beeps/ 3cycles andflashing icon
after 35 minutesif the useris out ofthe receiving rage. However, afterwardsif the 2-way
remote detect thesignal again fromthe system, 1beep sound willbe provided and flashing
icon will beON to indicatethe 2-way remoteis within range.
Note: If under Check-inrange mode, ifalarm triggered, thisfunction will automatically
turn off (disable).
The 2way remote
will respond:
Icon will onfor 2sec. and give 1 beep
sound to indicatethe function has been
turned ON.
Reminder disarm status(Programmable)
If programmed with" 1way reminderdisarm status to2way" feature , this function will
reminder disarm statusif disarming by1-way remote control.The 2-way remotewill display
disarm icon andgive 2 beepsound .
Vehicle statuschecking
Turn on LCD displayback light
The 2-Way remote offer thefeature to check the current status of the car, simply press
button once withinproper operation range. The main unitwill send the signals to
the 2-Way remote about thevehicle current status.
Simply press button once, the backlight of LCD display will turn on 5 seconds and
also check thevehicle status.

- To ARM the system:
To arm your system within proper operation range, simply press button once (while system
in disarmed or Acc off position) . The system will respond one siren chirp, one lights flash,
doors lock, disable engine starter, LED will begin flashing quickly until all sensor inputs are active
- LED will start blinking slowly (flash once per second) to indicate the system is in full armed.
- Defective Zone Bypass & Alert:
- Auto Reset:
If a violation occurs the system will respond by sounding the siren and flashing the lights for
approximately 30sec. before the system resets itself and continues to protect your car. If violation
still occurs the system, siren and lights will working for 8 cycles then the system reset itself and
continues to protect other zones.
- Arm without siren chirp :
You may temporarily to arm your system without siren chirp , to operate it by simply press button
once then within 3sec. press button once.
The system will armed and without one siren chirp,
Note: this features is only activated under the system is in disarmed and Acc off position,.
If the security system is armed at the same time that an input is active (such as a door opening
or hood / trunk opening ), you will hear one siren chirp to indicate arming and after 8 seconds
a second siren chirp to indicate Bypass Notification. A Bypass Notification chirp means that the
security system ignores the input that was active when the system was armed, until that input
ceases.
Defective zone Siren chirps 2-way beeps 2-way LCD indicator
2-way LCD display: + One beepsound
Note: Youmay press 2-way remote button onceto check again which zone is not closed.
Door opened 3 chirps 1 long + 3 short
Trunk opened 4 chirps 1 long + 4 short
Hood opened 5 chirps 1 long + 5 short
-13-
Standard features:

- To DISARM the system :
To disarm your system within proper operating range, simply press button once (while
system in arm position). The system will respond two siren chirp, two light flash, doors unlock,
Enable your engine starter, LED off.
- Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, siren and lights will Indicates
4 chirps and 5 flashes to identify which zone was triggered. LED mode indicates the following
different triggering.
flash 2 times after a pause Sensor 1st-stage triggered
flash 3 times after a pause Sensor 2nd-stage triggered
flash 4 times after a pause Door switch triggered
flash 5 times after a pause Trunk switch triggered
flash 6 times after a pause Hood switch triggered
Flash 7times after a pause Ignition switch triggered
- 2-way LCD Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, the 2-way remote will respond
2 short beep follow with melody sound, and LCD display will indicates different icons as under:
1st-stage sensor
triggered
2nd-stage sensor
triggered Door switch triggered
Trunk switch triggered Hood switch triggered Ignition switch triggered
Note: Before the ignitionturn on, you may realized again which zone been triggered by press
button (status check)once, the LCD will display triggeredzone again.
-14-
2-way LCD display: + Twobeep sound

- Disarm without siren chirp :
Todisarm your systemwithout siren chirp , simply press button once then within 3sec.
press button once.
Note: this features isonly activated underthe system is in armed position,.
- Silent arm mode :
The system providea feature toturn OFF the siren, simply press 2-way button of press
(while system indisarmed or Acc off position). The systemwill respond onelights flash,
doors lock, disableengine starter, LED will begin flashing quickly until all sensor inputsare
active - LEDwill start blinkingslowly (flash once per second) to indicate the systemis full
armed.
Note: Under SilentArm mode, if Sensor, Door, Hood ortrunk been triggered, the siren will
not activated, butif Ignition been triggered will activated the siren.
- Automatic REARM (programmable):
If the systemis disarmed byremote and adoor is not opened within approximately 30
seconds the systemwill automatically rearmitself. This featureguards against disarming
caused by accidentalor unintended operationof the remotetransmitter. Mainunit will
sends signal tothe 2-Way LCD remote andindicates ARMmode with onebeep sound.
- Passive arm (programmable):
If set programmemode to "WITH", while turn Ignition OFF, then close the last door ,system
will provide 2siren chirp and 2 light flash and LED flashing fast to indicated that the system
is in passivearming mode. After 30sec. Thesystem will armby itself and LED flashing slowly
to show thesystem is in arming mode. Main unit sends the signal to the 2-Way LCD remote
and indicatesARM mode with one beep sound .
This system alsoprovide under passive arming with door lock or withoutdoor lock
feature (please see"programme mode" features. ) During the period of 30sec.passive
arming, if adoor is opened, Led will light on and itwill re-passive arming when the door
closed again.
2-way LCD display:
2-way LCD display:
2-way LCD display:
Two beepsound will provided to
to indicate thatthe system is in
Passive arm mode.
Flashing icon toindicate that the
system is inAuto re-armingmode.
-15-
+ One beepsound
Icon flashing
indicator
Icon flashing
indicator

- Panic mode:
If you arethreatened in ornear your vehicle,you can attractattention by press button
for 2sec. systemwill triggering for30sec. To stop Panicmode at anytime, simply press
any button once.
Note: Tostop panic mode,simply press any button on the remote and the system will
be armed.
- Dual stage shock sensor:
This device onlyactivates after 8seconds of armingstate; this ispreventing from the
weak impact causedby the driverwhile leaving thecar.
The device operates:
-Light impact will activate the 1st stage sensor by giving 5 short warning chirps. 2-way
remote will respond5 beeps andflashing icon asunder.
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 30sec. 2-way
remote will respondmelody and flashingicon as under.
NOTE: Adjustmentsare made viathe rotary controlabove the shocksensor.
- Remote sensor by pass :
This system offer2stage sensor optional.Within 8sec. afterset arming, topress button
once , thesystem will give 2 short chirps and 2 lights flash, thus the 1st stage shock
sensor has beenturn off.
Press button onceagain, within 8sec.the system willgive 3 shortchirps and 3 lights
flash, thus the2nd stage shocksensor has beenturn off.
If press button once (at 3times) again within8sec. of armingthe shock sensor will
turn ON again.
Note: - if remotesensor bypassed, itwill be detectedagain by nextarming.
- if armedwith silent mode,to operate sensorbypass will onlyindicate by lights flash.
2-way LCD display:
2-way LCD display:
2-way LCD display:
2-way LCD display:
+ 5 beepssound
Under Panic mode,the 2-way remote
will respond melodysound and
flashing icons .
+ Melody sound
1st stage sensorbypass. 2nd stage sensorbypass.
-16-
Flashing
PASS
PASS

- Car search mode:
The system providea feature toeasy find your car position, simply press button once
when in armedafter 8sec. The system willrespond by 5chirps and 5 lights flash.
- Valet mode:
To entervalet mode: Disarm the systemand turn Ignition switch to ON position then press
button + forover 2 seconds, or press Valet/over-ride switch for over 5 seconds, until
siren give 1long with 1short chirp andLED light ON to confirm the system is in valet mode.
When the systemis in thevalet mode itcan not be armed. The door lock andunlock will
function as keyless entry system.
To exitvalet mode:
Turn Ignition switch to ONposition , thenpress button + for over 2seconds,or press
Valet/over-ride switch for 5 seconds. You will hearsiren provide 1 long with 2 short chirps
and LED lightOFF to confirmexit this modeand in alarm mode. The 2-Way remote will
respond 1 longand 2 shortbeeps.
- Ignition controlled door lock/unlock(programmable):
If programmed withthis feature, turn Ignition ON after 10 seconds the doors will auto
locked , butwithin this 10 seconds the door has been opened this feature will bypassed,
till next timeof ignition on.
When turn IgnitionOFF, the doors will unlock for take off, if programmed with ignitionoff
door unlock.
Note: Youmay manage lock and unlock doors in ignition onposition by short pressing
button to lockdoor or pressing to unlock door.
2-way LCD display:
Note:
Under Valetmode, each time
turn Accoff , thesiren will give
2 chirps fornotification.
- Passive immobilizer (programmable):
If programmed withthis function, whenturn off ignitionswitch for 30 seconds or you open
and close thedoor, itwill disable theengine starter right way . TheLED will flash twice
per second.
Exit: Todisarm this functionby (1) simplypress button once.LED off.
Note: Under this mode,if ignition forcebeen turn ON, siren will give 1long + 1 short chirps
warning, 10seconds laterwill activate thealarm, the 2wayremote will indicate Anti
car-jack icon andwarning sound. To disarm itwith programmed "Valet SW or PIN
code " feature.(Please see Emergencydisarm.)
2-way LCD display: + One beepsound

- Arming without Remote control:
This function givesyou a possibilityto Arm and Disarm the system use original key and Valet
switch, After driving and ignition keep ON , open the door, then turn off the ignitionKey and
press the Valet switch once,then closed thedoor, thesystem will armed immediately.
Note: if programmed withPassive arm feature,this feature willnot activated.
Note: if you failureto lock the door with original key within 15sec.,then you mayrepeat
it's procedure again
(This specify procedureto avoid anyfalse arm the system through indoor switch or
other situation etc.,..)
- 2 step disarm:
This system offers2 step disarm.It's a feature that make it possible to silence and reset
the system whileit is triggering,without disarming thesystem. If the system is triggered
and the sirenhas been sounding,pressing any button once on the remote transmitter will
stop the triggerand return theunit to the armed state.
Note: If press 2-wayremote control buttononce, will stopthe beep sound and LCD display
will indicate theintrusion icon for2sec. Press any button again to stop alarm triggering.
- Remote trunk open:
Simply press andhold button over2 seconds, thechannel will output for 1 second pulse ,
this feature normallyfor open thetrunk.
Note: If trunk hasbeen remote opened in arming position, trunk switch willdelay sensing for
30 seconds, andthe shock sensor will be bypassed.
2-way LCD display:
In Armedposition, if remote trunk open, the 2-way
LCD will displaytrunk icon and give one beep .
If trunk closed,trunk icon offand give one beep.
If still keepopened, after 1Min. The 2-way remotewill
give pre-warn beepsound.

- Siren chirps ON/OFF (programmable):
This programme featurecontrols the chirps that confirm thearming , disarming and intrusion
alert of thesystem.
Note: Set siren chirpoff, if door, hood ortrunk not closed,siren will activated.
- Power disconnecting memory :
Alarm is builtin memory on main unit. Generally, after alarm power is cut off and reconnect,
main unit willread back these data make the alarm to resume.
- Red/black wire positive (+) programme input :
This wire Red/blackis a (+)positive input canbe controlled functionsas : reverse
warning / Doorlock /AV swfor 2nd step disarm .
Reverse waring:
If programmed withthe feature, when youare reversing yourcar the parking lights will
flashing and sirenwill chirping (if programmed with siren) to prevent accident impacts to
animal or humanbody.
Note: you can proceedthe Reverse warning without siren chirps : (1) when you activated
the Disarm w/ochirp before Ignition On. (2) whenyou reversing theCar simply press
the button once.
Door lock :
If programmed withthe feature, doors willlock when activatethis wire.
AV sw for 2nd step disarm:
If programmed withthe feature, whendisarming the system by the remote, however the
engine will stillblocked, turn onthe ignition the2way will indicateflash icon andgive
beep sound toindicate that theengine is blocked.
Exit: Turn ignitionON then pressthis AV switch once to release the start killer. This AV sw
can be installedany O/E switch as long as it (+) positive input.
- Status LED timer:
If the alarmsystem armed after 24 hours, the LED will blink shortly once per second.
Armed after 25~48hours, the LED will blink shortly once every 3 seconds.
Armed after 48hours, the LED will blink shortly once every 5 seconds.
-Horn pulse:
If programmed withHorn pulse output,for additional vehicle's horn honk output alert.
- Emergency reset switch: (for installer only)
If the remotehas been lost or damage, or forgot the PIN code number the owner can
enter the carby using the key. Itwill act the alarm. To disarm the alarm turn ignition on
and connect "resetswitch" for over 2sec. , it will disarm the alarm immediately.(Please
ask your installerthis reset switch location).
Note: after this emergencyreset activated, the PIN code will resumed factory setting
PIN code " 2 . 5 "

Control Channel (-) features:
- Comfort /window close :
If programmed withthe feature, this channel will constant output for 30sec. When arming the system.
- 2nd stage door unlock:
If programmed withthe feature , to operate it by press button at 2nd time , 2nd stage door unlock
will be outputfor passenger side .
- Remote latched:
If programmed withthe feature, tooperate it whenignition off, pressbutton for over2sec.,
siren will give1 chirp andthe Channel willconstant output.
Toexit by ignition off and pressbutton over 2seconds, siren will give 2 chirp and
the channel willstop output.
- Dome Light:
If programmed withthe feature , the channel will constant output 30sec. when disarming . Turn
ignition switch ONwill stop the channel output.
- Pager :
If programmed withthe feature, this channel will output when system trigger .
-Arm W/Engine running:
If programmed withthe "Arm W/Engine running, this feature for the car to keep engine running after
arriving at yourdestination.
Tooperate this feature by pressing for2sec. while driving or ignition ON , the siren will give one
chirp and theLED will start flashing Green color, at the time the system is in standbymode, the
owner must followunder process to activate the "Arm W/Engine running " mode.
(1) Within 15sec. Turn Ignition OFF(engine still keep running), open and close door to leave the car.
Note: If within this15sec. press anybutton once willexit the mode,LED off.
(2) While leaving thecar by open and close the door, within 5sec. press button once, the system
will arm anddoor lock immediately, the parking lights will keep flashing, and the status LED will
flashing Green color, however the engine will still keep running. The2-Way remote will respond
under icons flashingas long as turbo time finished.
Exit mode :
Pressing button once of the remotecontrol within enginerunning mode ,the system
will exit turbomode and turn back in armed position.
NOTE:
1. In enginerunning mode, the sensor zone trigger will be bypassed until the programme
time finished.
2. In enginerunning mode, if door, hood or trunk has been triggered, engine will stop
running and alarmingthe system, simply press button todisarm the system.
(1) Afterleaving the car, within 5sec.
If press wrongbutton will exit mode.
(2) Afterleaving the car, within 5sec.
If without press button will exit
mode automatically.
Flashing
Note:
2-way LCD display:

- Turbo mode:
If programmed withthe feature , this channel will constant output when ignition turn on for over
1 minutes. Itwill keeps the engine running after arriving at your destination by ignition off for a
programmable of 1,3, 5, or 10 minutes. Thisallows the system's timer to conveniently cool down
the turbo afteryou have left the vehicle.
Note: in turbo modetime , if arming the system, sensors will be bypassed and LED flashing
Green color for a programmed turbotime.
Important: Turbo modeshould be used only in open areas. Never start and run the vehicle
in an enclosedspace such as a garage or carport.
2-way LCD display:
NOTE:
you may disablethis turbo mode
after ignition turnoff ,by press
button once, theCH-5 will
stop outputting.
- CH-5 (-) programme time output:
This channel-5 isa negative (-500mA)output features, thischannel can beprogrammed
(1)- Arming outputfrom 1~120sec.
(2)- Press button ,output from 1~120sec.
(1)- Arming output1~120sec. if programmed,this channel willactivate when arming,the
output timing can be programmed from1 to 120seconds.
(2)- Press button output1~120sec. If programmed, to operate this channel by press
button for over2sec. This channelwill constant outputfor programme time.
Exit: When this channelis outputting, ifpress button once,it will stopoutputting.
NOTE: This channel canbe programmed pulsedelay time (1~120sec.),If programmed,
channel-5 will delayoutput with programmepulse delay time.
Flashing
Table of contents
Other Eaglemaster Car Alarm manuals

Eaglemaster
Eaglemaster E8 User manual

Eaglemaster
Eaglemaster E2 User manual

Eaglemaster
Eaglemaster E1 Plus User manual

Eaglemaster
Eaglemaster AS-232T User manual

Eaglemaster
Eaglemaster LT-6200 User manual

Eaglemaster
Eaglemaster E5 G7 User manual

Eaglemaster
Eaglemaster E5 User manual

Eaglemaster
Eaglemaster CA-168 Safety guide