Eaglemaster E5 G7 User manual

E5 G7
No.TR-44
2-WAY Remote Car Alarm System
With 868 Mhz Frequency - FSK Solution

About Your System
NOTE:
Congratulations on your purchase of this state-of-the-art vehicle security system.
With proper installation this system will provide superior protection and performance for
many years to come.
What is included:
A control module
A FSK 868Mhz Antenna module
One 5-button 2-way LCD remote transmitter
One 4-button 2-way LED remote transmitter
Dual stage shock sensor
High output 6-tone siren (optional)
Full set wire harness
Pin switches
Options and Accessories:
This system includes several optional inputs and outputs allowing the creation of a
completely personalized security and convenience system by offering many optional
features such as:
2nd stage door unlock
Channel programme time output
Remote Channel latched
Engine turbo time mode
Check range notification
Arm/disarm chirp on/off
*Many require additional parts and/or labor, see store for details
Some of the features described in this manual may required additional parts and/or
labor, and may not be included as part of the standard installation of this unit.
Additionally, many features of this security system have selectable options that must be
activated or programmed during the system's installation. These items will be identified
in the following sections. Please discuss these features and any questions you may
regarding the installation of this product with your authorized dealer.
Window close control
Anti car-jack mode by Remote/Door switch
Arm with Engine running mode
Parking Lights pulse output (for hazard switch)
Personal PIN code protection
Reverse warning

Functions of remote transmitters
The remote transmitters integrated with the security system use the most perfect and
reliable radio frequency transfer as opposed to all car security systems being sold at the
moment. Some of modern skilled car hijackers use the devices known as code grabbers
allowing to accept and keep a signal transferred by the remote control of the car security
system. As soon as the driver is out the code is used by the hijacker to disarm the system.
Unlike the remote controls described above the remote transmitters integrated with your
security system change the code of the transferred signal each time when the button is
pressed, therefore, when a hijacker reproduces the signal grabbed from your remote
transmitter, the security system just will not react.
Fig.1
2WAY LCD REMOTE
Functions of remotetransmitter buttons
Button to arm the system (ARM)
Button to disarm the system (DISARM)
Button to control Trunk / CH-1 active
Button to control car status / turn on LCD back light
Button to Panic/Anti car-jack mode
NO.TR-44 FSK
NO.TX-4R FSK
2WAY SIMPLE REMOTE
Dual color Red/Green LED
Transmitting with Red flashing
Receiving with Green flashing

Standard 2way LCD icon instructions
Remote transmitting a signal.
SystemArmed.
Passive arming &
Auto re-arming mode.
Panic mode.
Check-in range turn ON status.
System Disarmed.
Zone1
1st-stage sensor bypass.
Zone2
1st-stage sensor bypass.
SilentArmed.
Zone1
2nd-stage sensor bypass.
Zone2
2nd-stage sensor bypass.
2way battery level indication.

Door open when armed. Trunk open when armed. Hood open when armed.
Zone1
1st stage sensor triggered.
Zone1
2nd stage sensor triggered.
Zone2
1st stage sensor triggered.
Zone2
1st stage sensor triggered. Door switch triggered. Trunk switch triggered.
Ignition switch triggered.
Hood switch triggered. Immobilizer mode.

Engine running mode. Alarm Clock . Countdown timer
Temperature check.
(Optional features) Turbo mode. Call / page mode.
Battery conservemode. Remote button lock Vibrate mode.
Valet mode. Safety mode/ Safe status
Anti car-jacking mode.

Remote Function Table:
Functions Step Condition
Arm and door lock
Arm without siren chirp
Zone1- 1st-stage bypass
Zone1- 2nd-stage bypass
Car search mode
Standby Anti-Hi-Jack mode
Disarm and door unlock
Disarm without siren chirp
Keep Engine run mode
Zone2- 1st-stage bypass
Zone2- 2nd-stage bypass
Remote trunk open
Status check & Back light
Enable check-in range
Panic mode
Anti hi-jack mode
Press once
Press over 2sec. until 1 beep given.
Press once within 5sec. of arming.
Press twice within 5sec. of arming.
Press once after 5sec. of arming.
Press over 2sec. Until 1 beep given.
Press once
Press over 2sec. until 1 beep given.
Press over 2sec. Until 1 beep given.
Press once within 5sec. of arming.
Press twice within 5sec. of arming.
Press over 2sec. Until 1 beep given.
Press once
Press once within 5sec. of arming.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Disarmed & ACC off
Disarmed & ACC off
Arming within 5sec.
Arming within 5sec.
Arming after 5sec.
ACC ON
Armed
Armed
ACC ON + Door open
Arming within 5sec.
Arming within 5sec.
ACC OFF
Any time
Arming within 5sec.
ACC OFF
ACC ON

Functions Step Condition
Silent armed
Valet mode
Remote button lock (on/off)
Vibrate mode on/off
Battery conserve mode
Time adjust mode
Alarm clock time setting
Countdown timer
Press over 2sec. Until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 4sec. until 2 beep given.
Press over 6sec. until 3 beep given.
ACC OFF
ACC ON
Remote battery discharge/replacement
If the battery becomes exhausted, the remote will emit extra long beep, While press any
button on the remote, few seconds later the indicator will flashing for identify.
The battery discharge is displayed on the LCD screen as the icon with the status
indicator . Also you can pay your attention that the effective distance for the transmitter is
being reduced.
To replace the batteries of 2-way remote
- Bend the top part of the cover a bit, move it up and remove,
- Remove the discharged battery,
- Place the new battery (AAA) observing polarity,
- Carefully place the cover back.
To replace the batteries of 1-way remote
- Loose the screws on the back side of the transmitter housing and separate two
halves of the transmitter housing,
- Remove the discharged battery,
- Place the new battery 12V 23A observing polarity,
- Carefully place the cover back (please do not damage the LED and switchers on the
Circuit board);
tighten the screws on the back side of the transmitter housing.

2WAY simple remote function with dual color Led indicator:
Press arm button once
Press arm button over 2sec. in ignition OFF
Press disarm button once
Press over 2sec.
1 green flash to indicate arming status
1 green flash to indicate arming status
1 green flash to indicate arming status
2 green flashes to indicate disarming
status
Red flashing to indicate failed receiving
Red flashing to indicate failed receiving
Red flashing to indicate failed receiving
Red flashing to indicate failed receiving
0.5sec.
0.5sec.
0.5sec.
0.5sec.
0.5sec.
0.5sec.
0.5sec.
0.5sec.
or
or
or
or
Arming the system:
Silent arm mode:
Panic mode:
Disarming the system:
Remote Trunk open:
Red flashing
when pressing
Red flashing
when pressing
Red flashing
when pressing
Red flashing
when pressing
Red flashing
when pressing
Response
Response
Response
Response
Press and hold the button for over 2sec.
Ignition ON, press both buttons over 2sec.
+

Ignition ON, press arm button over 2sec.
Arming status within 5sec., press button again
Ignition ON, press both buttons over 2sec.
1 siren chirp to indicate in standby mode
2 siren chirp to indicate 1st stage sensor bypass
3 siren chirp to indicate 1st stage sensor bypass
Standby Anti Hi-Jack :
Zone-1 sensor bypass:
Valet mode:
Red flashing
when pressing
Response
Response
Response
1 green flash to indicate turn on the mode
1long + 1short chirps given
Red flashing to indicate failed receiving
0.5sec.
0.5sec.
or
Red flashing
when pressing
Response
Press once
Press once
Press twice
1 green flash to indicate arming status
Red flashing to indicate failed receiving
0.5sec.
0.5sec.
or
Car search mode:
Response
Arming status after 5sec., press button again
1 green flash to indicate arming status
Red flashing to indicate failed receiving
0.5sec.
0.5sec.
or
Remote Anti Hi-jack :
Red flashing
when pressing
Response
Ignition ON, press both buttons over 2sec.
+

Battery conserve mode
The mode can be turned on/off 2-way receiving in the Disarmed mode if you simultaneously
press down the buttons until the zzz icon turn on. Being in the Disarmed mode
the remote pager turns off its receiver in 30sec.
To exit the mode, simply press the buttons until zzzz icon turn off.
2way remote button lock ON/OFF
For safety purpose, this 2-way remote can be lockout the remote button in order not to
mis-touched the buttons. Press button for over 2sec. until one beep is heard,
remote button is now locked. To turn on remote button, press button for over
2sec. until two beeps is heard, remote button is now unlocked.
Note: it will not lock the button , this button is anytime for check car status function.
2-way LCD display :
2-way LCD display :
Beeps 2-way remote feature
Vibrations
1-beep
1-beep
1-time
1-time
Remote with tone and vibration
Remote with vibration only
Remote with tone only
Vibrate mode on/off
Press button for over 2sec. the 2-way remote will respond tone & vibrate feature,
the button pressing 2sec. will change the feature, see under table:
Porgramme 2WAY LCD Remote

Check-in range notification (on/off )
Arming the system within 2 seconds, press button once on the 2way remote , the
system will enable this Check- in range function.
- With in 5 minutes, the 2-way remote will than give 1 beep sound every one minute for 5
cycles to remind the user within range.
- After 5 minutes, the 2-way remote will detect range every 10 minutes and without any beep
sound, the icon will constant on if the user within range.
For friendly usage, the 2-way remote will provide 2 beeps/ 3cycles and flashing icon
if the user is out of the receiving rage. However, afterwards if the 2-way remote detect the
signal again from the system, the icon will be ON to indicate the 2-way remote is within
range.
Note: If under Check-in range mode, if alarm triggered, this function will automatically
turn off (disable).
The 2way remote
will respond:
This Icon will turn on and give 1 beep
sound to indicate the function has been
turned ON.
Time adjust mode
Besides operating for alarm functions, LCD remote control additionally provides 24-hour
real time clock.
Instructions:
1. Press and hold Button for 2sec. to enter time-setup mode, 1 beep will be heard.
2. Press button to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button to turn up the numbers. Press button to turn down the numbers.
The button may be held down to scroll faster.
4. Press button to exit the setting mode. 2 beep will be heard.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Minutes display
24-hour display

Alarm Clock Setting
This function useful to warn the user by pre-setting alarm clock time, if pre-setted
time's up, the 2way remote will give warning beep for 1 minutes.
(Press any button once to stop warning beep)
Instructions:
1. Press and hold Button for 4sec. until its give 2 beeps ,then release the buttons,
Alarm clock icon will start flashing to indicate in setting mode.
2. Press button to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button to turn up the numbers. Press button to turn down the numbers.
The button may be held down to scroll faster.
4. Press button to Enable the alarm clock, 1 beep will be heard and exit .
Press button to Disable the alarm clock, 2 beeps will be heard and exit.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Countdown Timer Setting
This function useful to warn the user by pre-setting countdown time, if pre-setted
time's up, the 2way remote will give warning beep for 1 minutes.
(Press any button once to stop warning beep)
Instructions:
1. Press and hold Button for 6sec. until its give 3 beeps ,then release the buttons,
Countdown timer icon will start flashing to indicate in setting mode.
2. Press button to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button to turn up the numbers. Press button to turn down the numbers.
The button may be held down to scroll faster.
4. Press button to Enable the countdown timer, 1 beep will be heard and exit .
Press button to Disable the countdown timer, 2 beeps will be heard and exit.
Note: The remote will revert to normal operation from the set mode when 10-seconds has
elapsed without a button entry.
Minutes display
Minutes display
24-hour display
24-hour display
Alarm clock icon
Countdown timer icon

A page is the signal the control module sends to the remote controls confirmation of
receipt of a command or alarm system status. When the remote control receives a page
it will generate a page notification to the user (notifications are audible beeps) and the
LCD Icons will display the current system status.
Command Page
When a command (arm/disarm, remote start , or auxiliary channel) from the remote
control is sent and received, the system will send a command page back to confirm receipt.
Note: When the system is in Valet mode, the remote control will show the lock icon and
unlock icon, but will not generate a command page.
Page Recognition (Acknowledgement)
To clear a page alert/notification, quickly press any button on the remote control. This
can be performed at any time during or after the page notification has occurred.
The remote control will not send a command to the system at this time; it will only clear
future repeats of the page notification. The next time a button is pressed on the remote
Vehicle status checking
The 2-Way remote offer the feature to check the current status of the car, simply press the
button once within proper operation range. The main unit will send the signals to the
2-Way remote about the vehicle current status.
2WAY signal paging features

Display Beeps Vibrations Trigger
1st sta ge-Sensor warning
2nd stage-Sensor triggering
Trunk switch triggering
Door switch triggering
Hood switc h triggering
Ig nition trig gering
1st sta ge-Sensor warning
2nd stage-Sensor triggering
5 short
Melody 1
5 short
Melody 1
Melody 2
Melody 3
Melody 4
Melody 5
1 times
1 times periodically
1 times
1 times periodically
2
5 times periodically
times periodically
3 times periodically
4 times periodically
Zone 1
Zone 1
Zone2
Zone 2
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be sent to the remote
control. When the remote receives an Alarm Page, the LCD icons will display the alarm
system status information and the remote control will generate beeps.

-To ARM the system:
To arm your system within proper operation range, simply press button once (while system
in disarmed or Acc off position) . The system will respond one siren chirp, one lights flash,
doors lock, disable engine starter, LED will begin flashing quickly until all sensor inputs are active
- LED will start blinking slowly (flash once per second) to indicate the system is in full armed.
-Defective Zone Bypass & Alert:
If the security system is armed at the same time that an input is active (such as a door opening
or hood / trunk opening ), you will hear one siren chirp to indicate arming and after 8 seconds
a second siren chirp to indicate Bypass Notification. A Bypass Notification chirp means that the
security system ignores the input that was active when the system was armed, until that input
ceases.
-Auto Reset:
If a violation occurs the system will respond by sounding the siren and flashing the lights for
approximately 30sec. before the system resets itself and continues to protect your car. If violation
still occurs the system, siren and lights will working for 8 cycles then the system reset itself and
continues to protect other zones.
- Arm without siren chirp :
You may temporarily to arm your system without siren chirp , to operate it by simply press and
hold the button for over 2sec.
The system will armed and without one siren chirp,
Note: this features is only activated under the system is in disarmed and Acc off position,.
Defective zone Siren chirp s 2-way beeps 2-way LCD indicator
Note: You may press 2-way remote button once to check again which zone is not closed.
Door opened 3 chirps 1 long + 3 short
Trunk o pene d 4 chirps 1 long + 4 sho rt
Hood o pene d 5 chirps 1 long + 5 sho rt
Standard features:
2-way LCD display :
IMMO icon
indicate that
the engine
blocked

- To DISARM the system :
To disarm your system within proper operating range, simply press button once (while
system in arm position). The system will respond two siren chirp, two light flash, doors unlock,
Enable your engine starter, LED off.
- Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, siren and lights will Indicates
5 chirps and 5 flashes to identify which zone was triggered. LED mode indicates the following
different triggering.
flash 2 times after a pause Sensor 1st-stage tri ggered
flash 3 times after a pause Sensor 2nd-stage triggere d
flash 4 times after a pause D oor switch triggered
flash 5 times after a pause Trunk switch triggered
flash 6 times after a pa use H ood switch triggered
Flash 7times after a pause Ig nition switch triggered
- 2-way LCD Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, the 2-way remote will respond
2 short beep follow with melody sound, and LCD display will indicates different icons as under:
Zone1:1st-stage
sensor triggered
Zone1:2nd-stage
sensor triggered
Door switch
triggered
Trunk switch
triggered Hood switch
triggered
Ignition switch
triggered
Note: Before the ignition turn on, you may realized again which zone been triggered by press
button (status check) once, the LCD will display triggered zone again.
2-way LCD display : + Two beep sound
Zone2: 1st-stage
sensor triggered
Zone2: 2nd-stage
sensor triggered

- Disar m without siren chir p :
To disarm your system without siren chirp , simply press and hold the button for over
2sec.
Note: this features is only activated under the system is in armed position,.
- Silent ar m mode :
The system provide a feature to turn OFF the siren, simply press 2-way button
of press(while system in disarmed or Acc off position) . The system will respond one lights
flash, doors lock, disable engine starter, LED will begin flashing quickly until all sensor
inputs are active - LED will start blinking slowly (flash once per second) to indicate the
system is full armed.
Note: Under Silent Arm mode, if Sensor, Door, Hood or trunk been triggered, the siren will
not activated, but if Ignition been triggered will activated the siren.
- Automatic REARM (programmable):
If the system is disarmed by remote and a door is not opened within approximately 30
seconds the system will automatically rearm itself. This feature guards against disarming
caused by accidental or unintended operation of the remote transmitter. Main unit will
sends signal to the 2-Way LCD remote and indicates ARM mode with one beep sound.
- Passive arm (programmable):
If set programme mode to "WITH", while turn Ignition OFF, then close the last door ,system
will provide 2 siren chirp and 2 light flash and LED flashing fast to indicated that the system
is in passive arming mode. After 30sec. The system will arm by itself and LED flashing slowly
to show the system is in arming mode. Main unit sends the signal to the 2-Way LCD remote
and indicates ARM mode with one beep sound .
This system also provide under passive arming with door lock or without door lock
feature (please see "programme mode" features. ) During the period of 30sec. passive
arming, if a door is opened, Led will light on and it will re-passive arming when the door
closed again.
2-way LCD display : + One beep sound
2-way LCD display : Flashing icon to indicate
that the system is in Auto
re-arming mode.
Icon flashing
indicator
2-way LCD display :
Icon flashing
indicator
Two beep sound will provided to
to indicate that the system is in
Passive arm mode.

- Panic mode:
If you are threatened in or near your vehicle, you can attract attention by press button
for 2sec. system will triggering for 30sec. To stop Panic mode at any time,
simply press any button once.
Note: To stop panic mode, simply press any button on the remote and the system will
be armed.
- Dual stage shock sensor:
This device only activates after 8 seconds of arming state; this is preventing from the
weak impact caused by the driver while leaving the car.
The device operates:
-Light impact will activate the 1st stage sensor by giving 5 short warning chirps. 2-way
remote will respond 5 beeps and flashing icon as under.
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 30sec. 2-way
remote will respond melody and flashing icon as under.
NOTE: Adjustments are made via the rotary control above the shock sensor.
2-way LCD display :
2-way LCD display :
Icon flashing
indicator
2-way LCD display :
Under Panic mode, the
2-way remote will respond
melody sound and flashing
icons .
With 5 beeps sound
Zone 1 - 1st stage
sensor trigger
With 5 beeps sound
Zone 2 -1st stage
sensor trigger
With Melody sound
With Melody sound
Zone 1 -2nd stage
e sensor trigger
Zone 2 -2nd stage
sensor trigger

- Remote Zone1 sensor by pass :
This system offer 2stage sensor optional. Within 8sec. after set arming, to press button
once , the system will give 2 short chirps and 2 lights flash, thus the 1st stage shock
sensor has been turn off.
Press button once again, within 8sec. the system will give 3 short chirps and 3 lights
flash, thus the 2nd stage shock sensor has been turn off.
If press button once (at 3 times) again within 8sec. of arming the shock sensor will
turn ON again.
Note: - if remote sensor bypassed, it will be detected again by next arming.
- if armed with silent mode, to operate sensor bypass will only indicate by lights flash.
- Remote Zone2 sensor by pass :
This system offer 2stage sensor optional. Within 8sec. after set arming, to press button
once , the system will give 2 short chirps and 2 lights flash, thus the 1st stage shock
sensor has been turn off.
Press button once again, within 8sec. the system will give 3 short chirps and 3 lights
flash, thus the 2nd stage shock sensor has been turn off.
If press button once (at 3 times) again within 8sec. of arming the shock sensor will
turn ON again.
Note: - if remote sensor bypassed, it will be detected again by next arming.
- if armed with silent mode, to operate sensor bypass will only indicate by lights flash.
2-way LCD display :
1st stage sensor bypass.
1st stage sensor bypass.
2nd stage sensor bypass.
2nd stage sensor bypass.
2-way LCD display :