EAGTAC TX25C2 User manual

EAGTAC
High Performance Tactical Flashlight
http://www.eagletac.com
TX25C2
User Manual
EAGTAC TX25C2 oers maximum output
performance, versatile user interface,
tough build quality and rich accessories
like no other ashlight oers. This series
is designed for police, professionals, and
hobbyists.
WARNING - Lithium and Li-ion batteries
can explode or cause burns if disas-
sembled, shorted, or exposed to high
temperature. Do not mix with used or
other battery types or install backwards.
* Tested with 2xCR123A with energy saving feature enabled
Quick Specifications
LED
LED Lumen
ANSI Lumen
Runtime*
Output/AUX level
Circuit
Batteries
w/ extension tube
Voltage
XM-L U2
1030
852
1 to 90+ hrs
3 / 7
C3300 ST
1x18650 / 2xCR123A
2x18650/3-4xCR123a
2.7V-12V
Lithium and Li-ion battery can explode
or cause burns if disassembled,
shorted, or exposed to high tempera-
ture. Do not mix new and used batter-
ies. Do not mix batteries with dierent
brand, capacity, voltage, or install
batteries backwards. When the output
starts to dim (this implies battery is
almost drained), replace the batteries.
Do not drain the batteries completely
especially when you’re using two (or
more) batteries in series.
All EAGTAC ashlights are designed to
use “button-top” battery (battery with
protruding positive terminal). For
rechargeable li-ion battery, use only
EagleTac li-ion battery, or other
protected li-ion battery with compat-
ible length and diameter. Before using
the battery, check and ensure the
battery outer wrapping (the isolating
plastic lm that wraps around the
metal housing of the battery) is com-
plete. Broken battery wrapping may
lead to short circuit and damage to the
ashlight.
Battery Safety Precaution
On/O
Switch
Brightness
Adjustment
Tailcap
Quick Start Guide
1) Unscrew the tailcap and insert new
batteries (w/ protrude top) to use.
Ensure positive terminals is facing the
LED and the ring that holds the pocket
clip is tighten. Replace tailcap and
tighten snugly.
Basic ON and OFF
Turn on the light by press and release
the on/o button switch (<0.4s). To turn
o the light, press and release the
switch again.
For momentary on,
press and hold
the button switch
for immediate
output.
LED (Front) Tail-cap
Use it to prevent battery rattling.
CR123A battery magazine
pocket clip ring

Maintenance
Periodically clean the thread and o-rings
with a lint free cloth and apply a thin coat-
ing of EagleTac silicon-based lubricant to
the o-rings (not the machined thread).
Clean the battery contact, signal contact
(the gold coated pins and PCB contact
area), and machined thread with a lint free
cloth. Use a small drop of Deoxit red
cleaner solution (D100L series) to slightly
lube them for better conductivity and
smoother mode switching experience.
Color and diuser lter
Kit model come with diuser and color
lters. Replace the standard head with
the head (w/ o-ring installed) with
mounting thread, and install lter to use.
1) Replace batteries
2) Ensure tailcap is tight
3) Clean all conductive contacts
(see maintenance section)
4) Check battery polarity
Troubleshooting - Flashlight does not
turn on or fails to switch between
outputs normally:
“No Hassle” EAGTAC Warranty
For repair, replacement, or other inquiries
contact your EAGTAC dealer. You can also
reach our customer support via email at
[email protected].
We warrant our ashlights to be free from
defects in workmanship and materials. We will
repair, replace at our option, without charging
any product or part which is found to be
defective under normal use within 120
months from the date of purchase with the
proof of purchase.
Electronics, chargers and rechargeable batter-
ies are covered for a period of 12 months with
purchase receipt. Such repair or replacement
shall be the purchaser’s sole and exclusive
remedy under this warranty. Normal wear and
tear including batteries draining is not
covered, nor is damage resulting from modi-
cation, misuse, abuse, neglect, faulty battery,
battery leakage, improper maintenance or
repaired by anyone other than EAGTAC or
authorized dealer.
Do not touch or attempt to clean the
reector, as it will damage the reective
coating permanently.
Instant Turbo output
At any output level, press and hold the
on/o switch for 100% output. Release
the button to return to previous level.
Instant Strobe output
At any output level (even o ), double
press and hold the on/o button switch
for strobe output. Release the button to
return to previous level (or o ).
“Deoxit” is a trademark of Caig Laboratories, Inc.
Periodically clean
and apply Deoxit
red to ensure
smooth mode
switching and good
long term reliability.
Adjusting output level
Twist the head to select between three
output levels. You can pre-select the
desired output level
before turning on
the flashlight.
1st level 2nd, 3rd,
level
Hidden AUX. settings
With the head at tight position (1st
level), loosen to 3rd level and then
tighten the head at 1st level within one
second to enter AUX. setting. Repeat to
cycle through all settings. Turn o the
light or loosen the head to quit.
Strobe (I/II) Hi-Flash S.O.S. (I/II)
Beacon Lo-Flash (cycle)
To switch between tactical and regular
mode, turn on the ashlight at 1st level,
dial to 2nd level and then back to 1st
level for ten times within ve seconds.
Tactical Mode
100%
10%
Strobe
Regular Mode
100%
40%
0.5%
Level
1st
2nd
3rd
How to prolong battery life
1) Do not discharge the battery com-
pletely. Recharge often. Li-ion batteries
has no memory eect.
2) When the ashlight is going to be put
in storage for a long time, drain the
battery capacity to 50% or less for best
battery life.
Battery tube extender (optional)
We oer 3 cells (3xCR123A) and 4 cells
(4xCR123A or 2x18650) body extension
tube for extended runtime.
Energy saving feature
Enabled by default, this feature
reduces output by 25% (or 10% when
disabled) after 200 seconds at turbo
mode. To toggle this feature, turn on
the ashlight at 3rd level, and dial to
2nd level and then back to 3rd level for
ten times within ve seconds.