EarthQuake IMAGE-X User manual

Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545
Phone: [phone] Fax: [phone]
IMÃGE-X
IMÃGE-C25X IMÃGE-5X IMÃGE-6X IMÃGE-8X
Sound That Will Move You
Sound That Will Move You
High Fidelity
In-Wall Speaker Series
User’s Manual
www. sound.comearthquake

Mounting Considerations & Easy Installation Steps
www.earthquakesound.com 3
Simply tighten the screws by hand using a screwdriver to prevent the
mounting ears from snapping. Some resistance may occur the first few turns
of the screw as it makes its path through the plastic.
Figure 2
In-Wall Speakers
THOR
IW-SUB10
Q10B
Tactile Transducer
IW-SUB10
IMÃGE-C25X
IMÃGE-8X
IMÃGE-8X
IMÃGE-8X
IMÃGE-8X
LOCATE & MARK THE 2x4’s
Outline the hole using the
supplied speaker template -
stay clear from the 2x4’s.
1
CUT THE DRYWALL
Using a drywall saw, cut out the
opening.
2
CONNECT THE SPEAKER
Attach speaker wire and
insert the Imãge-X speaker
into the wall opening.
SECURE THE SPEAKER
Align the speaker in position
and tighten the screws
evenly to secure the unit.
4
PLACE THE GRILLE
Align the grille -
speaker cover - in
position. Gently push
cover into place.
5
3
Thank you for purchasing the Imãge Series In-Wall Speaker systems, one of
Earthquake's most valued in-wall speaker lines. With the proper installation and
operation, the Imãge speakers will provide a lifetime of durability and high-end
performance.
It is very important to follow all installation/mounting instructions and recommendations
in this manual closely and carefully to insure optimal performance operation and
longevity.
Features:
- Elaborate crossover networks with ±3dB tonal adjustments
- High quality capacitors and no distortion steel core inductors
- Easy Turn-N-Lock™ installation mechanisms
- 1” (25mm) silk dome NEO swiveling tweeters
- Low mass woven poly fiber woofer cones with extra wide rubber surrounds
- Paintable frames and grilles
Painting Guidelines:
The Imãge speakers are paintable and can accept virtually any type of paint. Spray and
roller paint applications typically provide the best results. When you are ready to begin
painting, remember to shield the driver and tweeter from the paint. Also, be sure to
remove the inner grille cloth prior to painting and replace it once the paint has
completely dried.
Speaker Placement:
The Imãge speakers are designed to be flush mounted in the walls or ceilings. To
optimize their acoustics you should follow these simple guidelines:
For best stereo reproduction the speakers should be placed an equal distance from
your listening position and separated so that the angle between them is between 40
and sixty degrees. The units should be placed with the tweeters near the ear level of
the seated listener.
Figure 1
Dear Valued Customer,
Specifications are subject to change without notice
2
WARNING: These products are
capable of generating high
sound pressure levels. You
should exercise caution when
operating these speakers. Long
term exposures to high levels of
sound pressure will cause permanent damage
to your hearing. Sound pressure levels
exceeding 85dB can be dangerous with
constant exposure, set your audio system to a
comfortable loudness level. Earthquake
Sound Corporation does not assume liability
for damages resulting from the direct use of
Earthquake speakers , and urges users to play
volume at moderate levels.
BASS
0dB
+3dB
-3dB
0dB
+3dB
TREBLE
-3dB
®
BASS
0dB
+3dB
-3dB
0dB
+3dB
TREBLE
-3dB
®

Specifications are subject to change without notice
4www.earthquakesound.com 5
I M Ã G E - 5 X S P E C I F I C A T I O N S
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
65Hz - 21kHz
93dB @ 1W/1M
8-Ohm
240 Watts
Infinite baffle, flush with wall
Wire Gauge Recommended:
Weight Per Speaker:
Mounting Depth:
Finish:
12
2 3/4” (71mm)
White / Paintable
Specifications
Specifications
I M Ã G E - C 2 5 X S P E C I F I C A T I O N S
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
50Hz - 21kHz
93dB @ 1W/1M
8-Ohm
400 Watts
Infinite baffle, flush with wall
Two-way system using:
two 5.25” low mass poly-fiber
cone midranges and one 1” silk
dome swiveling NEO tweeter
Two-way system using:
one 5.25” low mass poly-fiber
cone midranges and one 1” silk
dome swiveling NEO tweeter
Wire Gauge Recommended:
Weight Per Speaker:
Mounting Depth:
Finish:
12
17 11/16” (449mm) x 8 3/4” (221mm)
16 1/4” (416mm) x 7 3/8” (188mm)
3” (75mm)
White / Paintable
9 5/8” (245mm) x 6 1/8” (156mm)
11” (279mm) x 7 9/16” (192mm)
9 5/8” (245mm) x 6 1/8” (156mm)
11” (279mm) x 7 9/16” (192mm)
2 3/4” (71mm)
Outer Dimension:
Outer Dimension:
Cut Out Dimension:
Cut Out Dimension:
17 11/16” (449mm) x 8 3/4” (221mm)
16 1/4” (416mm) x 7 3/8” (188mm)
3” (75mm)
3.3 lbs.
5.8 lbs

Specifications Specifications
www.earthquakesound.com
Specifications are subject to change without notice
6 7
I M Ã G E - 6 X S P E C I F I C A T I O N S I M Ã G E - 8 X S P E C I F I C A T I O N S
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
52Hz - 21kHz
91.5dB @ 1W/1M
8-Ohm
350 Watts
Infinite baffle, flush with wall
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
52Hz - 21kHz
90dB @ 1W/1M
8-Ohm
500 Watts
Infinite baffle, flush with wall
Wire Gauge Recommended:
Weight Per Speaker:
Mounting Depth:
Finish:
12
3 1/4” (83mm)
White / Paintable
Wire Gauge Recommended:
Weight Per Speaker:
Outer Dimension:
Outer Dimension:
Cut Out Dimension:
Cut Out Dimension:
Mounting Depth:
Finish:
12
14” (356mm) x 10” (256mm)
12 3/4” (324mm) x 8 3/4” (222mm)
12 3/4” (324mm) x 8 3/4” (222mm)
10 3/4” (273mm) x 7 3/8” (187mm)
12” (305mm) x 8 3/4” (221mm)
10 3/4” (273mm) x 7 3/8” (187mm)
12” (305mm) x 8 3/4” (221mm)
3 1/4” (83mm)
3 3/4” • 93mm
White / Paintable
Rough-in Kit*: RK-6IW + BB-6IW (Back Box)
Two-way system using:
one 6.5” low mass poly-fiber
cone midranges and one 1” silk
dome swiveling NEO tweeter
Two-way system using:
one 8” low mass poly-fiber
cone woofer and one 1” silk
dome swiveling NEO tweeter
* Sold separately
14” (356mm) x 10” (256mm)
3 3/4” (93mm)
3.6 lbs 4.4 lbs