EarthQuake VTEK Series Supplement

Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545 • Phone: [phone] Fax: [phone]
VTEK MC5
MATCHED COMPONENT SET
www.earthquakesound.com
3-WAY 6X9” COAXIAL SPEAKER
VTEK-693
VTEK-52 /
VTEK-52Xi
2-WAY 5.25” COAXIAL SPEAKER
VTEK-42
2-WAY 4” COAXIAL SPEAKER
VTEK 6MC
MATCHED COMPONENT SET
The Sound That Will Move You.
Owner’s Manual & Warranty
EARTHQUAKE SOUND
Sound That Will Move You.
2-WAY 6.5” COAXIAL SPEAKER
VTEK-62 /
VTEK-62Xi
2-WAY 5 COAXIAL SPEAKERX7”
VTEK-57 /
VTEK-57Xi

Page# 3……......Warranty guidelines
Page# 4……......Components set dimensions
Page# 5……......Components set features and specifications
Page# 6 & 7……Coaxial speaker dimensions
Page# 8…….......Coaxial speaker features and specifications
Page# 9…….......Speaker installation
Page# 10…….....Separate installation/ Component set wiring diagram
Page# 11…….....Warranty card
Five (5) year limited warranty:
Earthquake warrants the original purchaser that all Factory Sealed New Audio Products be free from defects in material and
workmanship under normal and proper use for a period of five (5) years from the date of purchase (as shown on the original bill of sale with
serial number affixed/written on it). The five (5) year warranty period is valid only if an authorized Earthquake dealer properly installs the
productandthewarranty registrationcard isproperlyfilled outand sent toEarthquake SoundCorporation.If anon-authorized party installs
theproductaninety(90)daywarrantyperiodwillbeapplied.
(A) Five (5) years limited warranty plan coverage guidelines:
• First year: Earthquake pays for labor, parts, and ground freight (only in US mainland, not includingAlaska and Hawaii).
• Second year: Earthquake pays for labor and parts only, customer must pay freight both ways.
• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for parts and freight both ways.
(B) Warning:
Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem(s) will not be covered by the
five(5)yearlimitedwarranty.Customerwillbechargedaminimumofone(1)houroflabor(ongoingrates) plus shipping charges back to
customer.
(C) Earthquake will repair or replace - at our option - all defective products/parts subject to the following provisions:
• Defective products/parts have not been altered or repaired by other than an Earthquake factory approved technician.
• Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged by improper line voltage, used with
incompatible products, or have its serial number or any part of it altered, defaced or removed, or have been used in any way that is
contrary to Earthquake's written instructions.
(D) Warranty Limitations:
Warranty does not cover products that have been modified or abused. Including but not limited to the following:
• Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper use of cleaning materials/methods.
• Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust cap, burnt speaker voice coil.
• Fading, deterioration of speaker components & finish due to improper exposure to elements.
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper use of cleaning material.
• Burnt tracers on PCB.
• Product/part damaged due to poor packaging or abusive shipping conditions.
• Subsequent damage to other products.
warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with
a copy of the sales invoice.
A
(E) Service Request:
Toreceiveproduct/sservice, contactEarthquakeservicedepartment at(510)732-1000and request anRMAnumber(Return
Material Authorization), items shipped without a valid RMAnumber will be refused. Make sure you provide us with your complete/correct
shipping address, a valid phone number, and a brief description of the problem you are experiencing with the product. In most cases, our
techniciansmightbeabletoresolvetheproblemoverthephone,thuseliminatingtheneedtoshiptheproduct.
(F) Shipping Instructions:
Product/s must be packaged in its original protective box(s) to minimize transport damage. Shipper claims regarding items
damaged in transit must be presented to carrier. Earthquake Sound Corporation reserves the right to refuse product improperly packed.
Originalbill ofsalemust accompanyproductreturned for service.Weencourage youtoinclude withthepackage awrittendescription ofthe
problem.Shipproduct to: EarthquakeSoundCorp.2727McConeAvenue,Hayward,CA94545.Ph(510)732-1000.Youareresponsiblefor
thecostofshippingtheproducttoEarthquakeSoundCorporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from the five (5) years limited warranty policy
mustberesolvedaccordingtothelaws&regulationsofthecountyofAlameda-California.
Please keep this warranty information in your files for
future reference if necessary. It is recommended that
you stick your serial number here for future reference.
SERIAL NUMBER
Table of Contents
High-Performance and Sound Quality
WWW.EARTHQUAKESOUND.COM
2EARTHQUAKE SOUND • 5-YEAR WARRANTY 3
EARTHQUAKE SOUND
Thank you for choosing Earthquake Sound’s line of VTEK coaxial and component speakers for superior enhancement of your vehicle’s
audiosystem.Withproperinstallationandresponsiblelistening,yourVTEKspeakerswillgiveyouyearsofnearperfectsoundreproduction.
We strongly recommend you to have your new VTEK speakers installed by an authorized Earthquake Sound dealer: Installation
professionals employed by your dealer have the correct tools and knowledge to install your speakers neatly and successfully. Also, when
your new products are installed by an authorized dealer, your product will include a FIVE YEAR LIMITED WARRANTY. If you choose to
performyour owninstallation, yourwarrantywill besubjecttolimitations. Overthecounter authorized dealerwarrantiesmay veryfromone
dealertothenext.Pleasereadthewarrantyinformationinitsentiretyandusegoodjudgmentwhenmakingthesevitaldecisions.
Alternatively you may register your products online at
http://earthquakesound.com/form_reg.htm
For Easy On-line registration, Go To "www.earthquakesound.com/form_reg.htm"

VTEK MATCHED COMPONENT SPECIFICATIONS
VTEK-MC5
Sensitivity
Frequency Response
Nominal Impedance
Power Recommendations
Tweeter
Frequency Response:
1,500Hz - 22kHz
Crossover Networks
Model
45Hz - 23kHz (±3dB)
91dB @ 1W/1M
50 - 500 Watts
4 ohm
• 2-way network
• Military grade polypropylene film capacitors
• +3db/-3dB tweeter & woofer adjustment
• Poly switch tweeter protection
• 1” silk dome
• Soft rubber suspension
• Neodymium magnet
• Multiple mounting positions
VTEK-MC6
Woofer • 5” driver / electroplated carbon fiber cone body
• 25mm (over 1”) ASV voice coil
• Nomax/Romax high-performance spider
• Over hung butyl rubber surround
• 6.5
• 30mm (almost 1.25”) ASV voice coil
• Nomax/Romax high-performance spider
• Over hung butyl rubber surround
” driver / electroplated carbon fiber cone body
• 1” silk dome
• Soft rubber suspension
• Neodymium magnet
• Multiple mounting positions
• 2-way network
• Military grade polypropylene film capacitors
• +3db/-3dB tweeter & woofer adjustment
• Poly switch tweeter protection
50 - 600 Watts
40Hz - 23kHz (±3dB)
91dB @ 1W/1M
4 ohm
VTEK-MC5 Included Components and Parts
• Two VTEK-5w, 5.0-inch (127mm) carbon fiber woofers
• Two VTEK-25t, 1-inch (25mm) silk dome tweeters
• Two VTEK-500c crossover networks
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Two compact surface-mount fixtures
• Two metal woofer grilles with trays
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Twelve 8 x 1.25” (30mm) sheet metal screws
• Four 6 x .625” (16mm) sheet metal screws
• Two 1-inch (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Eight mounting clips for woofer mounting
• Two 6.4mm female crimpable connectors
• Two 4.7mm male crimpable connectors
• Two 2.8mm male crimpable connectors
• Twelve crimpable spade connectors
VTEK-MC6 Included Components and Parts
• Two VTEK-6w, 6.50-inch (160mm) carbon fiber woofers
• Two VTEK-25t, 1-inch (25mm) silk dome tweeters
• Two VTEK-650c crossover networks
• Two compact flush-mount fixtures
• Two compact angle-mount fixtures
• Two compact surface-mount fixtures
• Two metal woofer grilles with trays
• Two compact angle-mount fixtures
• Butyl adhesive putty for woofer grilles
• Twelve 8 x 1.25” (30mm) sheet metal screws
• Four 6 x .625” (16mm) sheet metal screws
• Two 1-inch (25mm) machine screws
• Two metal spring clips for tweeter fixtures
• Eight mounting clips for woofer mounting
• Two 6.4mm female crimpable connectors
• Two 4.7mm male crimpable connectors
• Two 2.8mm male crimpable connectors
• Twelve crimpable spade connectors
All specifications are subject to change without notice.
A
3kHZ PASS -3dB
WOOFER
--
INPUT
-
TWEETER
+
B
C
VTEK Component Crossover Dimensions (For 5” and 6” sets)
Height
A
Width B
Depth C
1.405", 35.7mm
5.07”, 129mm
4.21”, 107mm
VTEK-25C Dimensions
Diameter
A
Height B
1.405", 35.7mm
.75”, 19.05mm
This diagram displays only the raw tweeter.
Mounting components vary in size.
C
D
E
F
VTEK-5C Dimensions
Frame outer
diameter
A5.13”, 130.34mm
Grille tray outer
diameter
B6.49”, 165mm
Mounting depth
D1.92”, 49mm
Magnet width
E4.21”, 107mm
Cut out hole
F4.21”, 107mm
Grille protrusion
C71”, 18.034mm
VTEK-6C Dimensions
Frame outer
diameter
A6.49”, 165mm
Grille tray outer
diameter
B7.07”, 179.5mm
Mounting depth
D2.51”, 64mm
Magnet width
E4.03”, 102.29mm
Cut out hole
F5.66”, 144mm
Grille protrusion
C0.94”, 24mm
C
E
D
F
+
4EARTHQUAKE SOUND • VTEK COMPONENT SPECIFICATIONS 5
B
B
B
WWW.EARTHQUAKESOUND.COM

All specifications are subject to change without notice.
6EARTHQUAKE SOUND • VTEK COAXIAL SPEAKER SPECIFICATIONS 7
C
D
E
F
VTEK-42 Dimensions
Frame outer
diameter
A4.5” • 114.3mm
Grille tray outer
diameter
B5.75” • 146.05mm
Mounting depth
D1.81” • 46mm
Magnet width
E2.96” • 75.34mm
Cut out hole
F3.72” • 94.69mm
Grille protrusion
C.079” • 20.066mm
VTEK-52 Dimensions
Frame outer
diameter
A5.13” • 130.34mm
Grille tray outer
diameter
B6.50” • 165mm
Mounting depth
D2.023” • 51.4mm
Magnet width
E3.22” • 81.93mm
Cut out hole
F4.72 • 120mm
Grille protrusion
C0.70” • 17.6mm
VTEK-62 Dimensions
Frame outer
diameter
A6.49” 165mm•
Grille tray outer
diameter
B7.07” 179.5mm•
Mounting depth
D2.51” 64mm•
Magnet width
E4.03” • 102.29mm
Cut out hole
F5.74” 146mm•
Grille protrusion
C0.94” 24mm•
VTEK-57 Dimensions
Frame outer
diameter
A8.64” x 5.51 • 219 x 140mm
Grille tray outer
diameter
B6.49” • 165mm
Mounting depth
D2.32” • 59mm
Magnet width
E3.46” • 88mm
Cut out hole
F7.20 x 5.07” • 183 x 129mm
Grille protrusion
C0.89” • 22.606mm
VTEK-693 Dimensions
Frame outer
diameter
A9.27” x 6.45” • 235 x 164mm
Grille tray outer
diameter
B
Mounting depth
D
1.42” • 36.068mm
Magnet width
E4.33 • 110mm”
Cut out hole
F8.58” x 5.66” • 218.03 x 144mm
Grille protrusion
C
B
A
B
164mm•6.45”
166.64 • 6.56”
B
C
D
E
F
C
D
E
F
204.8mm•8.06”
112.5mm•4.42”
118mm•4.64”
C
C
D
D
E
F
B
B
119.28 • 4.69”
E
F
3.75” • 95.25mm
WWW.EARTHQUAKESOUND.COM

All specifications are subject to change without notice.
8EARTHQUAKE SOUND • INSTALLATION 9
VTEK COAXIAL SPECIFICATIONS
VTEK-42
Woofer
Model VTEK-693
Tweeter
Sensitivity
Frequency Response
Nominal Impedance
Recommended
Amplifier Power
VTEK-52
VTEK-52Xi VTEK-62 VTEK-62Xi
VTEK-62: 4-Ohm
VTEK-62Xi: 2-Ohm
VTEK-57
VTEK-57Xi
Nominal Impedance
Mid-range
• 4” diameter
• Glass fiber cone
• 25mm ASV VC
• NOMEX/ROMEX
spider assembly
• PistonMax™
• 20mm
• Silk dome
• Neodymium magnet
• Multiple mounting
positions
75Hz - 22kHz (±3dB)
89 dB @ 1W/1M
50 - 300 Watts
4 ohm
N/A
• 5-1/4” diameter
• Glass fiber cone
• 25mm ASV VC
• NOMEX/ROMEX
spider assembly
• PistonMax™
•
• Silk dome
• Neodymium magnet
• Multiple mounting
positions
20mm
55Hz to 22kHz (±3dB)
89 dB @ 1W/1M
50 - 400 Watts
VTEK-52: 4-Ohm
VTEK-52Xi: 2-Ohm
N/A
• 5" x 7” diameter
• Glass fiber cone
• 25mm ASV VC
• NOMEX/ROMEX
spider assembly
• PistonMax™
• 20mm
• Silk dome
• Neodymium magnet
• Multiple mounting
positions
40Hz to 22kHz (±3dB)
90 dB @ 1W/1M
50 - 400 Watts
VTEK-57: 4-Ohm
VTEK-57Xi: 2-Ohm
N/A
• 6-1/2” diameter
• Glass fiber cone
• 25mm ASV VC
• NOMEX/ROMEX
spider assembly
• PistonMax™
• 20mm
• Silk dome
• Neodymium magnet
• Multiple mounting
positions
45Hz to 22kHz (±3dB)
90 dB @ 1W/1M
50 - 500 Watts
N/A
• 6" x 9” diameter
• Glass fiber cone
• 30mm KSV VC
• NOMEX/ROMEX
spider assembly
• PistonMax™
• 20mm
• Silk dome
• Neodymium magnet
• Multiple mounting
positions
25Hz-22kHz (±3dB)
92 dB @ 1W/1M
50 - 700 Watts
4 ohm
• 2” (50.8mm)
VTEK-62 INCLUDE
•
w/ built-in adjustable 20mm silk dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight(8) speaker mounting clips
• Eight(8) 1.35” (34.925mm) sheet metal screws
• Two sets of specially designed speaker cables
Two VTEK 6-1/4” glass fiber cone woofers
VTEK-52 INCLUDE
• Two VTEK
w/ built adjustable 20mm silk dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight(8) speaker mounting clips
• Eight (8) 1” (25.4mm) sheet metal screws
• Two sets of specially designed speaker cables
5-1/4” glass fiber cone woofers
VTEK-693 INCLUDE
• Two VTEK
w/ built-in adjustable 20mm silk dome tweeters
and two-inch mid-range tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight(8) speaker mounting clips
• Eight(8) 2” (50.8mm) sheet metal screws
• Two sets of specially designed speaker cables
6" x 9” glass fiber cone woofers
VTEK-57 INCLUDE
• Two VTEK
w/ built-in adjustable 20mm silk dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight(8) speaker mounting clips
• Eight (8) 1.5” (38.1mm) sheet metal screws
• Two sets of specially designed speaker cables
5" x 7” Carbon fiber cone woofers
VTEK-42 INCLUDE
• Two VTEK
w/ built-in adjustable 20mm silk dome tweeters
• Two matching metal woofer grilles with trays
• Butyl adhesive putty for woofer grilles
• Eight(8) speaker mounting clips
• Eight(8) 1” (25.4mm) sheet metal screws
• Two sets of specially designed speaker cables
4” glass fiber cone woofers
GRILLE 4 SHEET METAL
SCREWS PER SPEAKER GRILLE TRAY
CUSTOM SPEAKER INSTALLATION
4 SHEET METAL SCREWS PER SPEAKER SPEAKER
FACTORY REPLACEMENT INSTALLATION
MOUNTING CLIPSFACTORY CUTOUT
NOTE: Hand tighten the screws
in a crisscross pattern to
avoid bending the speaker basket or stripping screws.
INSTALLATION APPLIES
TO BOTH COMPONENT
AND COAXIAL SPEAKERS
NOTE:
INSTALLATION APPLIES
TO BOTH COMPONENT
AND COAXIAL SPEAKERS
NOTE:
WWW.EARTHQUAKESOUND.COM

All specifications are subject to change without notice.
10
Flush Mount Assembly Flush Mount Installation
Top Ring
Panel
Mounting screws
Earthquake has provided two (2) mounting screws to be used in the Angle and Surface options
Angle Mount Assembly & Installation
Bottom Cup
Completed Flush Mount
Surface Mount Assembly & Installation
Top Ring
Panel
Bottom Cup
Push assembled tweeter through cut out hole
Cut diameter: VTEK-25S= 2” (50.8mm)
Twist on nut
until the
tweeter is
secured
Fasten the panel
clamp down from
behind the panel.
Panel
Panel Clamp
Top Ring Make sure that
the top ring and
bottom cup snap when pushed
together
Bottom Cup
Component Set Wiring Diagram
-
INPUT+
LP FULL 0dB -3dB
IN
- + +
3kHz PASS+
WOOFER - +
0dB 3dB+
TWEETER
-0 dB+-3dB+
TWEETER
AMP
-
-0 dB+-3dB+
WOOFER
WWW.EARTHQUAKESOUND.COM