Eaton CGLine+ Operating and maintenance instructions

CGLine+ Web Controller
CGLine+ Web Compact Controller
Target group: Skilled electricians
Zielgruppe: Elektrofachkraft
Public cible : Électriciens conrmés
Quick Installation Manual /Kurzanleitung / Guide d’installation rapide
ZNO2050500 PrB 03/2020

2Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
Description /
application area
This short instruction manual describes
only a quick commissioning procedure
of the CGLine+ Web Compact Controller.
A complete Installation and Operating
Instuction are downloadable from the
website of the CGLine+ Web Compact
Controller.
Commissioning and
modifying network settings
Please connect a patch cable with RJ45
plugs between the Compact Controller
and a PC (e.g. notebook).
Safety notes
CAUTION
The CGLine+ web interface must be
operated in undamaged and
functional state.
When carrying out maintenance work
with the device the device must be
de-energised.
When carrying out device maintenance,
observe national safety and accident
prevention regulations and the safety
notes in the operating instructions below
designated with .
CYBERSECURITY
This chapter provides guidelines to securely
deploy the CGLine+ Web Compact Controller
and minimize the cybersecurity risk to the
installer system.
• Asset identification and inventory:
Ensure that the CGLine+ Web Compact
Controller is labelled and inventoried
using the Part number and Mac address
printed on the product label, and also
the IP address configured during the
installation of the material and actual
firmware version.
• Restrict Physical access: Ensure that
physical access to the CGLine+ Web
Compact Controller is restricted only
to authorized user(s). CGLine+ Web
Compact Controller
supports the physical access ports RJ-45,
USB that can be used to tamper the
device. Access to these ports should be
restricted to authorized personnel only.
Secure the facility and equipment rooms
or closets with access control mecha-
nisms such as locks, entry card readers,
guards, man traps, CCTV, etc. as appro-
priate. Monitor and log the access at all
times. Before connecting any portable
device through a USB port or SD card
slot, scan the device to prevent unau-
thorized access.
• Restrict Logical access: Access to ‘Admin’
& ‘Service’user accounts should be
restricted to authorized personnel only
as system configuration can be tam-
pered by abusing these accounts. Ensure
password length, complexity and expi-
ration requirements are appropriately
set, particularly for all administrative
accounts (e.g., minimum 10 characters,
mix of upper- and lower-case and spe-
cial characters, and expire every 90 days,
or otherwise in accordance with your
GB
Conformity to standards
Compliant with: EN 60950-1.
Developed, manufactured and tested
according to DIN EN ISO 9001.

3
Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
GB
organization’s policies).
• Restrict Network Access: Ideally,
CGLine+ Web Compact Controller
should be installed on a segre-
gated network. However, when the
CGLine+ Web Compact Controller
is connected to a wider network,
make sure that the IP address and
MAC address are filtered at the
router side, or using a firewall. In
addition to this, open only the ports
used by the CGLine+ Web Compact
Controller (SMTP as configured, 587
for SMTPS, 443 for HTTPS, and 5000
for OPC communication).
• Logging and event management:
Make sure you log all relevant
system and application events,
including all administrative and
maintenance activities. Logs should
be protected from tampering and
other risks to their integrity (for
example, by restricting permissions
to access and modify logs, transmit-
ting logs to a security information
and event management system,
etc.). Ensure that logs are retained
for a reasonable and appropriate
length of time. Review the logs regu-
larly. The frequency of review should
be reasonable, taking into account
the sensitivity and criticality of the
CGLine+ Web Compact Controller
and any data it processes. The details
how to export the logs are defined
in chapter 7.14.
• Secure maintenance: In case the
firmware of the device needs to be
updated, you will be contacted by
your Eaton local support.
• Business continuity / cybersecurity
disaster recovery: Eaton recom-
mends incorporating CGLine+
Web Compact Controller into the
organization’s business continu-
ity and disaster recovery plans.
Organizations should establish
a Business Continuity Plan and a
Disaster Recovery Plan and should
periodically review and, where pos-
sible, exercise these plans. As part
of the plan, important device data
should be backed up and securely
stored, including the current con-
figuration and documentation of the
current permissions / access con-
trols, if not backed up as part of the
configuration. The CGLine+ PC can
be used to save the configuration of
a CGLine+ Web Compact Controller
using the “save file” button in the
main page.
• Decommissioning: It is a best prac-
tice to purge data before dispos-
ing of any device containing data.
Guidelines for decommissioning
are provided in NIST SP 800-88.
To ensure data is unrecoverable,
CGLine+ Web Compact Controller
must be securely destroyed. Method
of destruction include disintegra-
tion, Incineration, Pulverization, or
Melting of the electronic inside the
CGLine+ Web Compact Controller.

4Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
1. PANEL DESCRIPTION
Left / Back Validate / Select
Cancel / Back
Home
Log out + reactivate the
screen in save mode
Log out + switch off
the screen
Multi-tap keypad
(0: Special characters
#: Uppercase / Lower case)
Switch on/off
the screen
Activate USB
Green : OK
Blinking : Test
Red : Default
Right / Validate
Up
Down
USB cable A-B (option)
230V/AC
2. NETWORK SETTINGS

5
Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
The CGLine+ Web Compact controller is supplied as standard with the fixed IP address
192.168.1.200.
Operation via dhcp (dynamic IP address assignment) is possible but not factory-activated.
Because typical company networks only permit own-assigned IP addresses, we recommend
configuring network settings via direct connection to a PC, e.g. a notebook.
The network configuration can be done directly on the CGLine+ Web Compact con-
troller. The connection to a PC via a patch cable is optional.
The devices must be in the same subnet, meaning the network card of the PC must be set
to 192.168.1.xxx (not equal to 200), e.g. 192.168.1.50 (subnet to 255.255.255.0).
Settings for gateway and DNS must not be taken into account with a direct connection.
3. FIRST START
a
CGLine+ Compact
CGLine+ Compact
1.User
Select User for choosing a
password.
Enter a password of 10
characters maximum.
Then validate with OK.
11:40
Login : User
Password
21/01/2020
OkCancel
X
230V/AC
CGLine+ Compact
2.Administrator
Go back to previous display.
Select Admin for choosing a
password.
Enter a password of 10
characters maximum.
Then validate with OK.
11:40
Login : Admin
Password
21/01/2020
OkCancel
X
The CGLine Web Compact Controller is now ready to be used !
b
c
11:40
Z1
CGLine+ Compact
Login
Line 1
Line 2
Z2 Z3 Z4
Operation
Blocked
Failure Test
No luminaire
d
When the CGLine+ Web
Compact Controller starts, a
loading page appears during
3 seconds.
Then, a recap of the entire
installation appears on
screen. You can detect easily
a failure and identify the line
and zone in which the
problem is.

6Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
4. GENERAL CONFIGURATION
aLogin as Admin, with the
password you previously chose.
Then select Commands in the
general menu.
11:40
Admin
21/01/2020
4.Commands
11:40
Login : Admin
Password
21/01/2020
OkCancel
X
a
b
4.1. Language setting
Login as Admin, with the
password you previously chose.
Then select Configuration in
the main menu.
11:40
Login : Admin
Password
21/01/2020
OkCancel
X
11:40
Admin
21/01/2020
3.Configuration
11:40
Admin
21/01/2020
>Configuration
1.General
2.Test
3.Input
4.Output
5.Network
6.Email
7.Address
Select
11:40
Admin
21/01/2020
>Configuration->General
1.Name
2.Password change
3.Time
4.Date
5.Language
Select
11:40
Admin
21/01/2020
>Configuration->General->Language
1.English
2.Français
3.Deutsch
4.Italian
5.Portuguese
6.Nederlands
Save
c
Select General and then
choose Language in the next
menu.
Select the language you need,
and then select Save for saving
your choice.
4.3. Initialisation of luminaires
4.2. Date and time setting
Stay in the General menu, and
select Time for updating the
time, and Date for updating
the date.
Select Save for saving the
updates.
11:40
Admin
21/01/2020
Controller date (dd/mm/yyyy)
Save
21/01/2020
Cancel
X
11:40
Admin
21/01/2020
Controller time (hh:mm)
Save
11:40
Cancel
X

7
Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
bEnter Initialisation commands,
and then choose All lines.
11:40
Admin
21/01/2020
>Commands
1.Addressed commands
2.Initialisation commands
3.Adaptive Evacuation
Select
11:40
Admin
21/01/2020
>Initialisation commands
1.All lines
2.Line 1 ( 5 Luminaire)
3.Line 2 (0 Luminaire)
Select
c
11:40
Admin
21/01/2020
Operation in course
Line_1 : 5 Line_2 : 0
Select Search all lamp, and wait
for the complete loading.
Check the number of lamps, and
click on .
dOPTIONAL : You can change the
dates of automatic tests.
Go back to main menu, and
select Configuration.
Then select Te s t .
11:40
Admin
21/01/2020
3.Configuration
11:40
Admin
21/01/2020
>Configuration
1.General
2.Test
3.Input
4.Output
5.Network
6.Email
7.Address
Select
Select the test group you want
to update.
Choose the type of test, and
configure the new test time.
11:40
Admin
21/01/2020
>Configuration->Test group 1
1.Function test
2.Duration test
Select
11:40
Admin
21/01/2020
>Next functional test
1.Time : 18:00
2.Date : 01/01/2099
3.Test period : 07 days
4.Save
Select
Once the test features are
updated, select Save.
11:40
Admin
21/01/2020
>Next functional test
1.Time : 18:00
2.Date : 01/01/2099
3.Test period : 07 days
4.Save
Select
Conguration Saved
eThe CGLine+ Web Compact Controller is configured with basic settings. For all
configuration details, please see refer to CGLine+ Web Compact Controller user
manual.
If one or more luminaires are
missing, please refer to complete
user manual.

8Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
5. PC NETWORK CARD SETTING
1
2
Mark the entry Internet protocol
version 4 1, then continue with
“Properties” 2.
PC network card setting:
To modify the network settings of the PC open the system control
Network and release centre
Modify adapter settings
Right mouse click on “LAN connection”
Properties.
The following screen is displayed:

9
Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
Usually the network card is on DHCP, i.e. “Automatically reference IP address”.
Modify the entry to “Use the following IP address”and specify the following
values for the IP address and the subnet mask (displayed automatically):
IP address: 192.168.1.50
Subnet mask: 255.255.255.0
Clicking on OK assumes the settings so that the web page of the CGLine+ Web Compact
Controller can now be opened via any web browser, e.g. Firefox. Open a web browser and
enter the IP address“https://192.168.1.200” into the address bar.
The network card modifications should be reset following configuration of the network set-
tings of the web controller.
The start screen of the CGLine+ web controller now opens.
1
A login 1is necessary. Two accounts are available:
1. User:Admin Password:Enter the password you chose for Admin
2. User:User Password: Enter the password you chose for User
To modify the network settings, please login as Admin.
CGLine+ Compact
2.Administrator

10 Quick installation manual CGLine+ Web Compact Controller ZNO2050500 PrB 03/2020 www.eaton.com
Before accessing the webserver, two security pages are displayed on the browser by
security protocols.
The following web pages appear:
Click on Continue to this website on the first page.
Click on Advanced on the second page, and then on Add Exception.
IMPORTANT
A certificate error message can be displayed during the first connection to the controller
website.
Confirm by clicking on Continue to reach the login page. For installing the certificate, click
on CA certificate on the left.
The certificate can now be imported via your browser. The steps to follow can be different
according the browser you use (watch tutorial videos on videos.eaton.com).
The function of the website is also given without certificate, but it will alway require the
confirmation of this security notice.