Eaton IL01222025E Manual

IL01222025E
Effective Date 07/11
Instruction Leaflet for Series C
F - Frame Motor Operator
DO NOT ATTEMPT TO INSTALL OR PERFORM MAINTENANCE ON
EQUIPMENT WHILE IT IS ENERGIZED. DEATH OR SEVERE PERSONAL
INJURY CAN RESULT FROM CONTACT WITH ENERGIZED EQUIPMENT.
ALWAYS VERIFY THAT NO VOLTAGE IS PRESENT BEFORE PROCEEDING.
1
CONTENTS:
Motor operator 1x
Mounting Screws (103.5 mm) 4x
Mounting Screws (103.5mm
Groove) 4x
Mounting Screws (10 mm) 4x
Springwashers(φ4mm) 8x
Washers(φ4mm) 8x
Nut(M4) 4x
W
A
RNING

Page 2 IL01222025E
Effective 11/2007
2
Assemble four mounting screws with nuts and washers.
Torque to 0.44 to 0.6 N.m or 4 to 5 in lbs. Note: Mounting
screws with groove are for use with PAD 13D Plug – in.
3
•Turn breaker to the “OFF” position first.
•Line up breaker handle and molded trigger of
motor operator, and position motor operator on
the breaker.
4
Molded Trigger
Mounting Screws(10 mm)
Lock washers, Flat
washers
Breaker Handle
Mount motor operator to breaker
using mounting screws, lock
washers and flat washers
supplied. Torque to 0.44 to 0.6 N.m
or 4 to 5 in. lb
Mounting Screws(10 mm)
Spring washers, Flat
Washers
Mounting Screws
(
103.5 mm
)
Washers
Springwashers
Nut

Page 3 IL01222025E
Effective 11/2007
5
Manual Operations
•Move the slide knob to MANUAL position to expose the manual operating shaft. The control power
supply is cut off automatically.
•Insert the operating key into shaft slot. Turn the key clockwise to verify the breaker can be closed
and opened.
•Leave breaker in the ON position. Press the manual PUSH-TO-TRIP button on the breaker to verify
that the breaker moves to the trip position.
•Turn the operating key clockwise (approximately 180°) again. This should reset the breaker.
•Status window indicates Green / OFF, Red / ON and White / Tripped.
•Always remove the operating key and move the slide knob to the AUTO position before operating
electrically.
Slider knob
PUSH
-
TO
-
TRIP Button
Turn the key
(Clockwise Only)
Operating key
Status Indication
Windo
w

Page 4 IL01222025E
6
Motor Operator Wire Connection Diagram
Motor Operator Electrical Data
Voltage Frequency Inrush Current
208-240 VAC
110-127 VAC 50/60 Hz
220-250 VDC
110-125 VDC DC 1 A
24 VDC DC 3 A
48 VDC DC 2 A
1) A minimum 150 VA power source is recommended.
2) Maximum rate of operation: 6 operations per minute.
208-240VAC/220-250VDC Application 24VDC Application
110-127VAC/110-125VDC Application
24VDC/48VDC Application

Page 5 IL01222025E
Effective 11/2007
8
LOCK-OFF
Move slide knob to AUTO position.
Pull out the Lock-Off lever when
breaker is in OFF position, insert
one or two padlock shackles up
to .25 inch (6mm) in diameter.
CAUTION
The motor operator cannot be
locked off while it is in the ON
position.
7
Lock-Off Lever
Electrical Operation
•Make sure the slide knob is located in the AUTO position.
•Operating the OFF remote control switch will cause the breaker to go to its OFF position.
•Operating the ON remote control switch will cause the breaker to go to its ON position.
•Press the manual PUSH-TO-TRIP button on the breaker to verify that the breaker moves to the trip
position. Operating the OFF remote control switch again will reset the breaker.
•Status window indicates Green / OFF, Red / ON and White / Tripped.
•Always remove the operating key and move the slide knob to the AUTO position before operating
electrically.

Page 6 IL01222025E
Pittsburgh, PAU.S.A
Effective 11/2007 IL01222025E
9
Motor Operator Outline Dimensions