Eaton Cutler-Hammer I.B. 48020 User manual

Effective 4/00
I.B. 48020
Cutler-Hammer
Instructions for Mechanical Latch Attachment for Type L Medium
Voltage Vacuum Contactor
DANGER
HAZARDOUS VOLTAGE
Read and understand this manual in its entirety before
installing or operating a mechanical latch or contactor.
Qualified personnel must perform installation, adjustment,
and maintenance of this equipment. A qualified person is
one who is familiar with the construction and operation of
the equipment and who is aware of the hazards involved.
This instruction boo should not be considered all-inclu-
sive regarding installation, adjustment, and maintenance
procedures.
Read and understand all instruction literature for the SL
Contactor before performing any wor on the contactor or
the latch attachment.
DESCRIPTION
The SL Contactor in its standard configuration is a mag-
netically held device. A mechanical latch attachment can
be added to the standard SL that will maintain the
contactor in the closed position when power is removed
from the main operating coil. A separate unlatch coil must
then be energized to allow the contactor to open.
The unlatch coil is intermittently rated. Control power
should be applied to the coil only long enough to allow the
contactor to open. Two normally open auxiliary contacts
(wired in parallel) on the contactor should be used to open
the circuit to the unlatch coil.
Although the latch (closing) coil is continuously rated,
power should be removed from the coil after the contactor
is closed to insure that the contactor opens when the
unlatch coil is energized. Ma e certain that the close
pushbutton (or other device) is a momentary device that
will apply power to the latch circuit for a short time only.
Do not use a maintained device which will cause the
contactor to stay closed even after the unlatch coil is
energized. Do not wire a normally closed (NC) auxiliary
contact directly into the coil closing circuit to remove
power from the coil. To do so may result in a failure to
latch since the contact may open before the coils have
been powered sufficiently long enough to fully close the
contactor.
A typical control schematic for a mechanically latched
contactor is shown in Figure 2.
Figure 1: SL Contactor with mechanical latch installed.
Figure 2: Typical schematic for latched contactor

I.B. 48020
Page 2
Effective 4/00
INSTALLATION
The mechanical latch it is supplied as shown in Figure 3.
The it consists of two main components: the main latch
assembly and the roller brac et and bearing assembly.
Hardware for bolting the assemblies to the SL contactor is
also included. The contactor moving armature is not
supplied with the it. It is shown for illustration purposes
only, to identify the mounting location of the roller brac et
and bearing assembly.
Steps for Installation
1. Remove the existing roller brac et from the contactor
moving armature, if one is attached.
2. Secure the new roller brac et and bearing assembly
with two 6mm x 25mm bolts with loc washers and
torque to 85 in-lb (9.6 N-m). Insure that the side
flanges of the roller brac et are parallel with the end of
the armature plate. Note: If bolts longer than 25mm are
used, they will extend through the armature plate and
prevent the contactor from closing and sealing when
the main coils are energized.
3. Locate latch assembly into contactor, see Figure 4
4. Install four 8mm x 1.25 bolts 16mm long, with loc
and flat washers through the bottom of the contactor
base plate into the latch base plate, do not tighten at
this time.
5. With contactor energized, place a 0.5mm ( 0.020 in.)
feeler gage between roller bearing and rotating cam on
latch assembly, see Figure 5
When releasing the latch several parts of the contactor will
move with considerable force. Use caution to insure
fingers are not pinched as the contactor is forced open by
the return spring.
8. Route the two control wires from the full bridge diode
across the main coils, connecting them to the main
coil control wires with tie straps, and terminate them
at terminals 7 & 8 on the control board.
WARNING
DANGER
Follow necessary precautions including insuring that all
transformers are properly isolated before applying power to
contactor coil. If voltage is bac fed into a transformer,
high voltages will be generated on the transformer primary.
High voltage can cause serious injury or death.
6. Apply force to latch assembly, sliding cam towards
roller bearing, and tighten four mounting bolts through
contactor baseplate. Torque to 200 in-lb (22.6 N-m).
7. Release the latch by depressing the latch release tab
on the latch assembly. Refer to Figure 5.
Figure 3: Mechanical latch it
Figure 4: Location of latch assembly on contactor base
plate
Contractor Moving Armature
(not part of it) Roller Brac et and
Bearing Assembly
Main Latch Assembly

I.B. 48020 Page 3
Effective 4/00
LATCH REMOVAL
1. Remove latch control wires from terminals 7 & 8 on
contactor coil control board.
2. Remove the four 8mm x 1.25 bolts from the underside
of the base plate that secure the latch assembly to
the base plate.
3. Remove the two 6mm x 1.0 bolts from the front of the
contactor that secure the roller brac et assembly to
the armature plate.
COIL CHEC OUT AND REPLACEMENT
If the contactor fails to open when the unlatch coil is
energized, the coil may be faulty. To determine if the coil
has the proper resistance, connect an ohmmeter across
the coil leads where they are connected to the bridge
rectifier. Refer to table I for the correct impedance for the
different voltage coils.
TABLE I: UNLATCH COIL IMPEDANCE
Coil Volts Impedance
24 0.77 – 0.95
48 2.95 – 3.55
110/120/125 10.97 – 11.19
220/240 44.57 – 54.57
If the coil impedance is not within the ranges in table I, it
must be replaced. Follow the steps below for replace-
ment.
1. Remove latch control wires from terminals 7 & 8 on
contactor coil control board.
2. Remove the four 8mm x 1.25 bolts from the underside
of the base plate that secure the latch assembly to
the base plate.
3. Remove latch coil core retaining bolt (8mm x 1.25),
Figure 6, and remove all components secured by this
bolt.
4. Remove the 4mm x .7 screw securing full bridge diode
to latch coil brac et.
5. Remove old coil from core.
6. Insert coil core into new coil, insuring rubber gas et is
between core and coil bobbin.
7. Install 4mm x .7 screw securing diode to latch coil
brac et and tighten to 9 lb-in. Do not over tighten,
crac ing of diode housing could result.
8. Reassemble all components removed in step 3,
insuring steel shim is between coil core and coil core
brac et, and secure 8mm x 1.25 bolt to latch base
plate. Insure all components are correctly aligned and
the coil wires are not binding or pinched, Figure 7.
9. Reinstall latch assembly and adjust as described in
steps 3 to 8 in section on Installation.
Figure 5: Set gap between roller bearing and cam to .5mm
(.020 in.)
Figure 6: Coil core retaining bolt
Latch
Release
Tab

I.B. 48020
Page 4
Effective 4/00
LATCHED CONTACTOR IN AMPGARD® MEDIUM
VOLTAGE STARTER
When a latched contactor is installed in an Ampgard
starter, the contactor is mounted with the baseplate facing
the front of the enclosure. A reset mechanism is attached
to the rear of the medium voltage door to allow the
contactor to be manually unlatched. Refer to Figures 8,9
and 10 for more details.
Figure 7: Alignment of latch components Figure 9: Latch Release Button (Front of Medium Voltage Door)
Effective 4/00
Printed in U.S.A./CCI
Cutler-Hammer
221 Heywood Road
Arden NC 28704
The reset mechanism is factory set. Field adjustments
can be made by loosening the loc nut on the reset button
shaft and extending or retracting the blac phenolic
plunger.
Figure 8: Mechanical Release Lever
Trip Lever
Figure 10: Latch Release Mechanism (Rear of Medium
Voltage Door)