Eaton Crouse-hinds series User manual

DOCUMENT
1192
REVISION
B
April 26, 2019
Instruction Manual
FAA L-804
LED
804E-AP1
Elevated Runway Guard Light
InstructionManual
Crouse-Hinds by Eaton
Airport Lighting Products
1200 Kennedy Road
Windsor, CT06095
Copyright © 2019 CooperTechnologies Company
For Parts or Technical Service Call [phone]

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
ii
1Revisions
Revision
Number
Issue/Reissue
Letter Number
Description
Checked
Approved
A
A215-059
INITIAL ISSUE
KF
SD
B
A219-054
Page 15, figure 5: Added P/N 21696-3
OR 21696-4;
Page 19, figure 7: Added P/N 21696-4 to
power supply diagram.
KF
PG

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
iii
2ProductWarranty
Warranty
Refer to Eaton’s Crouse-Hinds Airport Lighting Products Terms and Conditions for product specific
warranty information.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
iv
3Warning Labels
DANGER:
DANGER
The hazard or unsafe practice willresult in severe injury or death.
WARNING:
WARNING
The hazard or unsafe practice could result in severe injury or death.
CAUTION:
CAUTION
The hazard or unsafe practice could result in minor injury.
NOTICE:
NOTICE
Possibly dangerous situation, goods might be damaged.
IMPORTANT:
IMPORTANT
Helpful information.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
v
4SafetyNotices
This equipmentis normally usedorconnectedto circuitsthat may employ voltages that aredangerousandmay be
fatalif accidentally contacted byoperating ormaintenancepersonnel.Extreme caution should be exercisedwhen
working with this equipment.While practicalsafetyprecautionshavebeenincorporated in this equipment,the
following rules must be strictlyobserved:
4.1 KeepAwayfrom Live Circuits
Operating andmaintenance personnelmust at alltimes observe allsafetyregulations.Do not perform
maintenanceon internalcomponentsorre-lamp with powerON.
4.2 Resuscitation
Maintenance personnelshould familiarize themselveswith thetechniqueforresuscitationfound in widely
published manuals offirst aid instructions.
IMPORTANT:
IMPORTANT
See FAA Advisory Circular AC 150/5340-26 for additional
information.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
vi
5Table ofContents
1Revisions............................................................................................................................ii
2Product Warranty............................................................................................................iii
3Warning Labels................................................................................................................iv
4Safety Notices.....................................................................................................................v
4.1 Keep Away from Live Circuits ..................................................................................v
4.2 Resuscitation.............................................................................................................v
5Table of Contents..............................................................................................................vi
6Part Number Explanation .................................................................................................1
7General Description...........................................................................................................2
7.1 General .....................................................................................................................2
7.2 Units without Control System Monitoring (6.6A) .......................................................2
7.3 On/Off Switch (Option -1 (6.6A)) Mode 1..................................................................2
7.4 6.6A Series Unit with Monitoring (Standard Unit or Option 5) - Mode 1 .....................2
7.5 115-250 VAC 50/60 Hz. Voltage Unit with Monitoring and On/Off Switch (Option 2) -
Mode 2......................................................................................................................3
7.6 24 DC Voltage Unit with Monitoring and On/Off Switch (Option 2) ...........................3
7.7 Logitrac Digital Monitoring (6.6A Series Circuit Only) ..............................................3
7.8 Environmental...........................................................................................................4
7.9FAA Specification.....................................................................................................4
7.10 Accessories:..............................................................................................................4
8Installation.........................................................................................................................6
8.1 General .....................................................................................................................6
8.2 6.6A Series Unit without Monitoring..........................................................................6
8.3 6.6A Series Unit with Monitoring (Standard Unit or Option 5) ....................................6
8.4 115-250VAC and 24VDC Voltage Unit without Monitoring.......................................7
8.5 115-250VAC Voltage Unit with Monitoring (Option 2) ..............................................7
8.6 24VDC Voltage Unit with Monitoring (Option 2) .......................................................7
8.7 Tools Required for L-804 Installation.........................................................................8
8.8 L-804 Unit Installation...............................................................................................8
8.9 Standard Monitoring Relay Connection for Option 2 ONLY.......................................8
8.10 Vertical Adjustment...................................................................................................9
8.11 Horizontal Adjustment...............................................................................................9
8.12 External Ground Stud ................................................................................................9

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
vii
9Periodic Maintenance......................................................................................................13
9.1 General ...................................................................................................................13
9.2 Replacement of LED Modules .................................................................................13
10 Troubleshooting...............................................................................................................14
10.1 General ...................................................................................................................14
10.2 Problem Solving Guide –6.6A.................................................................................14
10.3 Problem Solving Guide –120VAC & 24VDC..........................................................17
10.4 Recommended Field Quick Fix................................................................................18
11 Recommended Spare Parts (2 Year Supply) ...................................................................22
Appendix A.............................................................................................................................26
A-1 Typical Photometric Output @6.6 Amperes, Part Number 804E-AP1........................26
A-2 Light Beam Orientation for Elevated Runway Guard Lights......................................26
A-3 50542 Assembly Drawing (showing indicator LEDs)................................................27
List of Figures
Figure 1 - General Dimensions ...............................................................................................5
Figure 2 - Baseplate Installation Illustration ..........................................................................10
Figure 3 - Adjustment Illustration .........................................................................................11
Figure 4 - Installation Illustration (Option 2 ONLY)..............................................................12
Figure 5 - Power Supply Connections, P/N 21696-3 OR 21696-4...........................................15
Figure 6 - Power Supply Status LED Location ......................................................................16
Figure 7 - L-804 LED Current Power Supply Diagram..........................................................19
Figure 8 - L-804 LED Voltage Power Supply Diagram 120VAC ...........................................20
Figure 9 - L-804 LED Voltage Power Supply Diagram 24VDC .............................................21
Figure 10 - Parts Identification (Sheet 1 of 3) ........................................................................23
Figure 11 - Parts Identification (Sheet 2 of 3) ........................................................................24
Figure 12 - Parts Identification (Sheet 3 of 3) ........................................................................25

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
1
6Part NumberExplanation

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
2
7General Description
7.1 General
The Crouse-Hindselevatedrunwayguardlight (ERGL) is an ETL verified FAA L-804. The ERGL runway
guard light is an elevated light fixtureconsistingoftwo LED modules thatalternately flashes45-50per
minutein yellowto identify taxiway holding positionlines.The clearsignallenses are glassandare housed
in aluminumenclosures. Accessto eachLED module is made throughahinged coversecuredby locking
latches. No specialtools arerequired formaintenance.The UniversalPowerSupply is housedin an
aluminumenclosure attached betweenthe two LEDboards. UniversalPowerSupply can bechangedwith a
nut driverand disconnecting thefast-onterminals fromtheterminals. A spare doorwith replacement circuit
cards can be slid backontothe hingepin and fast-on terminals reattached to circuit card terminalblocks.
Positive angularadjustment is made by moving the hairpin cotteron thesupport pin through theappropriate
hole in the steelside supportsand post. The unit is attachedto a standardsteel10-1/4dia. B.C. L-867 light
base (customersupplied)andheavy12-inch diameterbase plate (customersupplied,see accessories,page 4)
with a 2-11 1/2 NPSM threadedaluminumcoupling. The coupling is prevented fromrotatingdueto jet blast
by an aluminumanti-rotationplate boltedto thebaseplate. In addition,thecouplingis preventedfrom
rotating andlifting out ofits aluminumslide fit mount by set screws. A stainless steeltetheris provided for
securingtheunit to the base plate. Poweris provided to theunit through an L-823style plug. A groundstud
is provided internalforunitswith monitoringand externalforunits without. Allhardwareis type 18-8
stainlesssteel. Poweris provided to theunit through an appropriate size isolationtransformer(not provided)
or name plate rated ACorDC powersources. The averageweight ofthe unit is approximately 45 lb.
7.2 Units without Control SystemMonitoring (6.6A)
Powerprovided tounit fromthe65W,6.6A isolation transformerthrough asupplied 5-pin molded L-823
plug. See Figure 7 on page 19(without monitoring).
7.3 On/Off Switch (Option -1 (6.6A)) Mode 1
Allows unit to be servicedorhave UniversalPowerSupplies changedin field without turning poweroffat
source. Switch isolatesthe secondary ofisolationtransformerfromthe internalcircuitry.
7.4 6.6A Series Unit with Monitoring (Standard Unit orOption 5) - Mode 1
Unit requires connection to a 65W,6.6A series secondary isolationtransformer. A molded female connector
(L-823, Style7) is providedforthe monitoringconnectionto a 5-pin L-823 style plug. The5-pin female
connectorprovides forconnectionto theisolation transformer,agroundlead forconnectionto theL-867
internalground stud,andtwo leadsforconnectingthe monitoring signallines. Shieldedmonitorleadsare
connected to the circuit card relay common and normally open orclosedcontact(customercan changethis
connectiondependingon theirpreference). The monitoringrelay (rated 120V, 2 A resistive load)will
provide asignalpath forfailuredetectionifthe fixture is not operatingcorrectly to a customerprovided
indicator. PerFAA AC150/5340-28, a threeorfive step FAA L-828constant current regulatorshould be
used forpoweringtheRunwayGuard Light.
ForOption 5, the monitoring connectoris changed toan L-823, Style 6 connectorfordirect power
monitoring connections toCooperCrouse-HindsLogitracDevice.The indication is typically set to NCfor
Option 5.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
3
7.5 115-250 VAC 50/60 Hz. Voltage Unitwith Monitoring and On/Off Switch
(Option 2) - Mode 2
A molded female connectoris providedforconnectionto a 5-pin L-823 style plug. The 5-pin female
connectorprovides forconnectionto the115-250 AC source,a ground lead forconnectionto the L-867
internalground stud,andtwo leadsforconnectingthe monitoring signallines. Shieldedmonitorleadsare
connected to the circuit card relay common and normally open orclosedcontact(customercan changethis
connectiondependingon theirpreference). The monitoringrelay is rated for120V, 2 A resistive load and
will provide asignalpathforfailuredetection ifthefixture is not operatingcorrectly toacustomerprovided
indicator. The fixtureis also equippedwith a photocellto controllight intensity. Photocellallows forfull
intensitylight outputfromfixture during high ambient lighting conditionsandthen reducesfixtureoutput
light intensityto 30% during lowambient light conditions.
7.6 24 DC Voltage Unit with Monitoring and On/Off Switch (Option 2)
A molded female connectoris providedforconnectionto a 5-pin L-823 style plug. The 5-pin female
connectorprovides forconnectionto the24DC source,a ground lead forconnectionto the L-867internal
ground stud,and forconnectingthe monitoring signallines. Shieldedmonitorleadsare connectedto the
UniversalPowerSupply common andnormally openorclosed contact (customercan change thisconnection
dependingon theirpreference). The monitoringrelay is rated for120V, 2 A resistive load andwillprovide a
signalpath forfailuredetectionifthefixture is not operating correctly to a customerprovided indicator. The
fixture is also equippedwith aphotocellto controllight intensity. Photocellallows forfull intensitylight
output fromfixture during high ambientlightingconditions and thenreducesfixtureoutputlight intensity to
30% during lowambient light conditions.
IMPORTANT:
IMPORTANT
Thephotocell isdisabled whenOption4 isordered.Option4,ICAO2.24outputis
constantforallbrightnessconditions.
7.7 Logitrac Digital Monitoring (6.6A Series Circuit Only)
This configuration is recommendedforuse with a Crouse-HindsDigitracALCMSComputer,but not
required. In addition,a Continuous Logitrac Adapter(CLA)and ContinuousLogitrac Device(CLD) unit
must be ordered asseparateitems and installed in thelightingvault and onthe Lighting circuit. Contact
Crouse-Hinds salesforassistance.Unit requires connectiontoa65W,6.6A series secondary isolation
transformerand Option5is required. Powerprovidedto theunitfromthe Logitrac througha supplied 5-pin
molded L-823 plug. A circuit number(CKT) and addressnumber(ADRS)must beprogrammed ontothe
CLD in orderforthemonitoring portionto functionwith the CLD. The CLA can report the monitoring
information directly to theCrouse-HindsDigitracComputerSystem,orthemonitoringinformationcan be
obtainedfroma dry contacton theCLA in the lighting vault. Connection to a threeorfivestep FAAL-828
Constant Current Regulatoris stillrequired.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
4
7.8 Environmental
Temperature: -55º to +55ºC
(-67º to +131ºF)
Altitude: 0 to 10,000 feet
Humidity: 0 to 100 percent
Wind Loading: Up to 300 MPH
7.9 FAA Specification
Unless noted,meetsrequirements ofL-804 perFAA AC150/5345-46 (latest version)and FAAEngineering
Brief No. 67 “Light Sources other than Incandescent and Xenon forAirportLight and ObstructionLight
Fixtures.” Fixture performance and operation has been verified by ETL. Fixture meets the requirements of
Low-Visibility Taxiway light Systems as specified in FAA AC150/5340-30. Also meets requirementof
ICAO Annex14 specification,Vol.1, Section 5.3.22 Configuration A,High Intensity. Light housingfront
surfaces,baffle plate andlenscapspainted black. Allotherexternalparts arepaintedaviationyellowwith
theexception offrangible coupling,stainlesssteelhardware,tether,hinge,andlatch.
Low intensityversionmeetsphotometric requirementsoutlinedin ICAO2.24. Low intensityversionis not
FAA certified by ETLoracceptedby FAA.
7.10 Accessories:
33003 65W 6.6/6.6 AMPSERIES ISOLATIONTRANSFORMER –6.6A INPUT.
33004 100W 6.6/6.6 AMPSERIES ISOLATION TRANSFORMER–6.6A INPUT.
33005 100W 20/6.6 AMPSERIES ISOLATION TRANSFORMER–20A INPUT.
AP1832, 12-3/8 INCH DIAMETER(10-1/4 DIA. B.C.) HEAVY BASEPLATEWITH2 INCH NPS
THREAD.
AP2832, 16 INCH DIAMETER(14-1/4 DIA. B.C.) HEAVY BASEPLATEWITH2 INCH NPS THREAD.
10046-282-PIN L-823 FEMALECONNECTOR ASSEMBLY.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
5
Figure 1 - General Dimensions

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
6
8Installation
8.1 General
LocationsforL-804 elevated runwayguard lightsare shown in FAA AC150/5340-28and FAA AC120-57A.
In addition,the10-1/4diameterB.C. steelL-867 light base shouldbe installed perabove mentioned advisory
circular. TheL-867 light base flange is installedwith the topofthe flange flush with theconcrete as finished
grade reference.This will maintain the maximum 26-inch unit mounting height at 20ºverticalorthe 14-inch
unit minimum mounting height to bottomoflens. A heavybase plate (P/NAP1832[12-3/8 dia.]or AP2832
[16-inch dia.]) should be used with thisunit due to highwind loadingrequirement. The 3/8hardware usedto
securethebaseplateshould havebolts1-3/4incheslong asa minimum (to attach tetherandanti-rotation
plate - 2-inch long bolts provided). Base plategasketand base plateshould be installed on light base,butdo
not fully secure bolts untilL-804 unit has beeninstalled.
DANGER:
DANGER
INSTALLATIONOFUNITTOBEDONEWITHPRIMARYPOWER OFF AND
SECURED.
8.2 6.6A Series Unit without Monitoring
Installappropriateisolation transformerinto light base andmake necessaryprimary powerconnectionsusing
L-823 connectors. Isolationtransformersecondaryconnectorwill seat in base plateL-823 connectorholder.
(Unit includesa Standard Monitoring Relay.See Section 8.9.)
8.3 6.6A Series Unit with Monitoring (Standard Unit orOption 5)
Monitoringis included with allunits,andtheuse ofan L-867 base with an internalgroundis required.
Installappropriateisolation transformerinto light base andmake necessaryprimary powerconnectionsusing
L-823 connectors.Attach powermonitoring cablesto the supplied 5-pin L-823 connector.Connect5-pin
molded female connectoras follows:L-823 plug to isolation transformer,L-823 receptacle to field remote
signalline,and green lead with ring terminalto light base internalgroundstud.
IMPORTANT:
IMPORTANT
Largediameterreceptacleisformonitorrelaycommoncontact andsmall diameter
receptacleformonitorrelaynormally(closedoropen)contact.
The 5-contactL-823 receptacle will connectto theL-804 unit’s 5-pin L-823 plug,5-contact receptacle seats
in baseplateL-823connectorholder.
ForOption 5, the monitoring connectionis changedto L-823, style 6,connectorfordirect connection tothe
Crouse-Hinds Logitrac Device.The style 6connectorwill directly connect tothe middle lead ofthe Logitrac
Device.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
7
IMPORTANT:
IMPORTANT
Connectingthestyle6 monitoringlead tothe incorrectLogitracleadmaydamage
theL-804unit.
8.4 115-250VAC and24VDC Voltage Unit without Monitoring
No monitoring installationshavea 5-conductorL-823 plug.The connectioncan be extendedusingCrouse-
Hinds part number10060-6-ABC where “ABC” is the length in inches. Option 4 includes one 394 inches
[10m] extension cable.
8.5 115-250VAC Voltage Unit with Monitoring (Option 2)
When monitoring is required,use an L-867base with an internalground. Installon appropriate light base
and make necessaryprimary powerconnections usingsupplied 5-pin L-823 connector.Connect5-pin
molded female connectoras follows:L-823 plug to input ACpower,L-823 receptacle to field remote signal
line L-823 plug and greenlead with ring terminalto light base internalgroundstud.
IMPORTANT:
IMPORTANT
Largediameterreceptacleisformonitorrelaycommoncontact andsmall diameter
receptacleformonitorrelaynormally(closedoropen)contact.
The 5-contactL-823 style receptacle will connect to L-804 unit’s 5-pin L-823 style plug,5-contact receptacle
seatsin base plate L-823 connectorholder.
8.6 24VDC Voltage Unit with Monitoring (Option 2)
When monitoring is includedwith unit,usean L-867 base with an internalground. Installon appropriate
light base and makenecessaryprimary powerconnectionsusing supplied 5-pin L-823 connector.Connect 5-
pin molded female connectoras follows:
•L-823 plug to input DCpower, Large Pin –Relay common,Small Pin –Monitoring.
•L-823 receptacle to field remote signalline L-823 plug.
•Green lead with ring terminal to light base internalgroundstud.
IMPORTANT:
IMPORTANT
Largediameterreceptacleisformonitorrelaycommoncontactandsmalldiameter
receptacleformonitorrelaynormally(closedoropen)contact.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
8
The 5-contactL-823 style receptacle will connect to L-804unit 5-pin L-823 style plug,5-contact receptacle
seatsin base plate L-823 connectorholder.
24VDC or 115-250VAC low intensity output withoutmonitoring unit supplied with extensioncable of33ft
(10m), 16AWGStyle8 secondaryextensioncable.Thisallows simple connectionto supply voltage.
8.7 Tools Required forL-804 Installation
Tools requiredforinstallation are 5/32inch Allen key,9/16 socket andwrench,phillip screwdriverand
channellocks to accommodate a minimumopening of1-3/4inches.
8.8 L-804 Unit Installation
WARNING:
WARNING
Be surePOWERisOFFand secured.
Place the anti-rotation plate on top ofbase plate. Hexcutout tobe overthreaded centerhubin baseplate.
Plug 5-pin L-823 style plug into mating receptacle held in centerofbase plate. WithL-804 unitupright,
engage frangible coupling threadsintobase platethreadedcenterhub a couple ofturns.
It is recommended that anti-seize compound(i.e.LoctiteAnti-seize 767or equal)be applied to frangible
coupling threadspriorto installationto preventgalling and seizing. Loosenthe set screwsin L-804 unit post
holding the frangible coupling. Thread frangible coupling allthe way down intothebaseplate. Align anti-
rotation platehexwith frangible coupling hex. Bolt anti-rotationplateto baseplate.
IMPORTANT:
IMPORTANT
Theanti-rotationplatewill bendslightlywhenfullyboltedinplace.
Bolt tetherto a base platemounting hole. Align L-804 unit yoke perpendicularwith taxiway centerline and
tighten thefourpreviously loosened set screws.Returnpowerto circuit. L-804 unit should begin flashing. If
L-804 unit provided with optionalOn/Offswitch,be sureswitchis in ONposition.
8.9 Standard Monitoring RelayConnection for Option 2 ONLY
You have an optionofanormally open ornormally closedcontactto be used forfailure monitoring. With
POWER OFF and secured, open the front cover of the enclosure. Locate CN10 (Common) CN7 “N.O.”
(No Alarms) or CN11 “N.C.” (Alarm Indication) on circuit board p/n: 50542. Wire per Figure4.
Option 2,120VAC and 24VDC FAA intensity(Not option4)units come with the MonitoringRelay
connectionwired as showedin thePowerSupply Diagrams.(SeeFigure 8&9)

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
9
8.10 Vertical Adjustment
The fixture can be aimed in elevation vertically from0 to +20 degrees. The verticaladjustmenthasbeen
factory presetat zero degrees. Remove one hairpin cotteron the adjustment pin on the post. Positionthe L-
804 unit to thedesired verticaladjustmentby aligningthe appropriatelymarked degreehole in the postwith
its mating hole in the yoke. Installadjustment pin removed fromzero degree holesthrough newdesired
verticaladjustment holes. Place the hairpincotterin the adjustmentpin hole.Verticalangle settingwill be
determined by thelocalairfield engineer. Referto FAA AC150/5340-28.
8.11 Horizontal Adjustment
The fixture can beaimed horizontally from-20 to +20 degrees. Thehorizontaladjustmenthasbeen factory
pre-set to zero degrees. Ifrequired,loosenthe fourset screws at zero degreeslocatedbottomofthe post.
Rotate the L-804 to the desiredhorizontaladjustment by aligning theappropriatemarked degreeholesonthe
post. Tightenthe set screwsfromzero degree holes at thenewdesiredhorizontaladjustment.Horizontal
angle setting willbedetermined by the localairfield engineer. Referto FAA AC150/5340-30 (latest
version).
8.12 External Ground Stud
An externalgroundstudis providedin the headenclosureforgroundingthe L-804 unit. Use #12AWG(3.5
sq.mm) minimum for groundwire.
IMPORTANT:
IMPORTANT
L-804 unitswithmonitoring haveaninternal ground. Also,thefemale5-pinL-823
styleplug ground should be connected to the internal L-867groundstud as
explainedinSection8.3.

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
10
Figure 2 - Baseplate InstallationIllustration

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
11
Figure 3 - Adjustment Illustration

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
12
Figure 4 - Installation Illustration (Option 2 ONLY)

DOCUMENT 1192
REV. B
Instruction Manual
L-804 Runway Guard Light, 804E-AP1
13
9PeriodicMaintenance
WARNING:
WARNING
Verify powerisOFF and securedbeforeaccessinginterioroflightheadsandcircuit
card controlbox.
9.1 General
At least every 6months,theL-804 unit should be checkedforthe following:loose hardware; tighten allloose
hardware. Waterinside light heads; replace broken lenses,worn gasketsandcheckhole plug seal(apply
RTV if necessary). Wiring; openenclosuredoorand make sureterminalsareproperly seated. Chipped
paint; touchup paintas necessary. Dirty lenses;clean with alcoholanddry with clean soft cloth. Dirty
photocellsensor:same as lens cleaning.
9.2 Replacement ofLED Modules
CAUTION:
CAUTION
Do notwork onfixturewhenenergized.
If replacement is required they should only be replaced with Crouse-Hinds partnumber50637 LED Module.
5/16 nut driveris required forchangingLED Module. Undothelatches on enclosure andopento gain access
to Module. DisconnecttheLEDModule lead terminals. InstallnewLED Module then reconnectwireleads
previously disconnected. Re-attach the four#8nutsand secure theLED board. Close enclosuredoorand
tighten thelatches making sureEMIgasket is notpinchedagainst door.