Eaton Shaper Series User manual

INS #Shaper IL525016EN
Installation Instructions - Shaper-1400-Color Cord
Installation Instructions - Shaper-1400-Color Cord
Installation Instructions - Shaper-1400-Color Cord
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the
attention of the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the
housing to assure you have received the correct material.
SAFETY: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited
ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do
not expose lighting fixture to rain, dust or other environmental conditions prior to installation and insertion of photo
control or shorting cap (if so equipped). Do not install the fixture near combustible materials or locate next to airflow
blocking surfaces within 6 inches. Best results will be obtained if installed and maintained according to the following
recommendations.
WARNING
Make Certain Power is OFF before starting installation
or attempting any maintenance.
WARNING
Risk of Fire/Electric Shock. If not qualified, consult an
electrician.
WARNING
Risk of Electric Shock – Disconnect power at fuse or
circuit breaker before installing or servicing.
WARNING
Risk of Personal Injury – Fixture may become damaged
and/or unstable if not installed properly.
 Do not mount luminaire within 6” of a combustible
surface.
 Do not handle luminaire by the glass. Do not touch
LEDs.
WARNING
Risk of Burn – Disconnect power and allow fixture to
cool before servicing.
ote:N These instructions do not claim to cover all
details or variations in the equipment, procedure,
or process described, nor to provide directions
for meeting every possible contingency during
installation, operation or maintenance. When
additional information is desired to satisfy a
problem not covered sufficiently for user’s purpose,
please contact your nearest representative.
ote:N This lighting fixture has been shipped complete
with one of several mounting options. Please follow
the installation instructions specific to the catalog
part that you ordered.
ote:N Care must be taken not to set lighting fixture down
on optical lenses or lift the fixture in the lens area.
ote:N Specifications and dimensions subject to change
without notice.

2EATON IL525016EN Installation instructions
Installation Instructions - Shaper-1400-Color Cord
INSTRUCTIONS:
1. Make sure power is Off.
2. Remove Shade and inspect Product Label.
3. Secure Shade with Coupler.
4. Cut Color Cord to length and strip the casing to access wires. Wrap Electrical Tape (provided by others) at the end of
fabric sleeving of Color Cord.
5. Apply Strain Relief to color cord below Electrical Tape.
6. Loosen the Reducer and allow Canopy to separate from Bar Strap. Mount the Bar Strap assembly to J-box (not
provided) with screws provided.
7. Using U.L. approved wire connectors: connect the neutral (white) wire to the supply neutral, connect the luminaire line
wire (black) to the supply line wire, connect the ground (green) wire to the supply ground.
8. Turn power on to test installation.
9. Raise Canopy flush to ceiling and secure with Reducer.
Strain Relief
Product Label
Color Cord
Shade
Lock Nut
Bar Strap
Nipple
Canopy
Reducer
Electrical Tape
Coupler
Figure 1.

3
EATON IL525016EN Installation instructions
Installation Instructions - Shaper-1400-Color Cord
Figure 2.
Figure 3.
INSTRUCTIONS:
1. Make sure power is Off.
2. Remove Shade and inspect Product Label.
Shade
Power Cord
Coupler screws into place
Product Label
Shade
3. Secure Shade with Coupler.

4EATON IL525016EN Installation instructions
Installation Instructions - Shaper-1400-Color Cord
4. Thread in Bar Strap and Lock Nut to the Nipple and mount to J-Box.
Figure 5.
5. Place the Reducer and the Canopy through the Color Cord.
6. Cut Color Cord to length and strip the casing to access wires. Wrap Electrical Tape (provided by others) at the end of
fabric sleeving of Color Cord.
ote:N To be careful when stripping not to damage the Cord.
Figure 4.
Lock Nut
Bar Strap
Canopy
Electrical Tape
Nipple
Reducer
Color Cord

5
EATON IL525016EN Installation instructions
Installation Instructions - Shaper-1400-Color Cord
Figure 7.
Figure 6.
7. Pull color cord through the Bar Strap and Strain Relief below the Electrical Tape.
8. Wire Black to live, White to Neutral, and Green to ground.
9. Secure the Canopy to the ceiling by threading in the Nipple. Secure the canopy to the ceiling by threading the reducer
into the nipple.

Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2018 Eaton
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. ILXXXXEN
June 9, 2018
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Eaton est une marque de commerce
déposée.Toutes les autres marques
de commerce sont la propriété de leur
propriétaire respectif.
Eaton es una marca comercial
registrada.Todas las marcas
comerciales son propiedad de sus
respectivos propietarios.
Product availability, specifications,
and compliances are subject to
change without notice.
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis.
La disponibilidad de productos, las
especificaciones y los cumplimientos
están sujetos a cambio sin previo
aviso.
Warranties and Limitation of Liability
Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.