Fly Dragon LIGHT SKY LED TX1810 BEAM User manual

USER MANUAL
PROFESSIONAL SHOW LIGHTING
LED
TX1810 BEAM
www.lightsky.com.cn/www.lightsky-china.com
FLY DRAGON LIGHTING EQUIPMENT CO., LTD
100~240V~ 50/60Hz

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
1
CONTENTS
1. General information 2
2. Safety instructions 3
3. Trait and skill specifications 7
4. Operation panel 8
5. Dimensional drawings 9
6. Mounting and Installation 9
7. Power supply and Signal connection 11
8. Display menu 13
9. DMX traits 21
10. Circuit connecting diagram 26
11. Trouble dispose 27
12. Cleaning and Maintenance 28
13. Duty exonerative and Copyright protection 28

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
2
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the
most innovative and reliable LED fixtures on the market today. Our
company has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the
instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information
regarding safety during use and maintenance.
UNPACKING: Thank you for purchasing our company products. Every
product has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your fixture for damage and be sure all accessories
necessary to operate the fixture have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box you should find: the fixture,
a DMX XLR cable, a power cable, and this user manual.
Please do not discard the shipping carton in the trash. Please recycle
whenever possible.
Notice: As part of our ongoing commitment to continuous
products update, company will keep the right to improve
this products, the information in this menu may be
changed in the future, the company reserve the right to
change the data without any advises.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
3
2. SAFETY INSTRUCTIONS
■Notice
To guarantee proper and consistent operation, it is
important to follow the guidelines in this manual. Our
company will not accept responsibility for damages
resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
■Mounting surfaces
It is permissible to mount the fitting on normally
flammable surfaces.
Please do not install the fixture onto combustible surface.
Ensure a minimum clearance of 0.2m around the cooling fans and
ventilation.
■Maximum ambient temperature
The fixture is intended for indoor application.
Do not operate the fixture if the ambient temperature (Ta)
exceeds 38℃.
■Temperature of the external surface
The maximum temperature that can be reached on the external
surface of the fitting, in a thermally steady state, is 60℃.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
4
■Protection against electrical shock
Connection must be made to a power supply system fitted with
efficient earthing(Class Ⅰ appliance according to standard
EN60598-1).
It is,moreover,recommended to protect the supply lines of the
projectors from indirect contact and/or shorting to earth by
using appropriately sized residual current devices.
■Connection to mains supply
The double insulation between the LV power supply and the control
conductor on the fixture.
Connection to the electricity mains must be carried out by a
qualified electrical installer.
Check that the mains frequency and voltage correspond to those
for which the projector is designed as given on the electrical
data label.
This label also gives the input power to which you need to refer
to evaluate the maximum number of fittings to connect to the
electricity line,in order to avoid overloading.
Don’t use the power cable when the insulation is damaged.
It must be the manufacturer or distributor or the professional

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
5
person to change the damaged power cable in order to avoid any
dangerous.
■Protection against explosion
The protection screen, lens or ultraviolet screen on the lamp
can be damaged to the degree of failure if visible damage, such
as a crack or deep mark, should be replaced.
■Protection optical radiation
Never look directly into the light source. You risk injury to
your retina, which may induce blindness.
■Maintenance
Never open this fixture while in use.
Please disconnect the power supply when begin to maintenance take
down the light.
Please disconnect the power supply when begin to maintenance take
down the light. Please let the parts cool down 10 minute at least
then begin to install.
The light source in this fixture shall be replaced by the
manufacturer or its service agent or similar qualification..
Do not revise the fixture or install any parts not from our

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
6
company.Please be aware that damages caused by modifications to
the device are not subject to warranty.
■The products referred to in this manual conform to the European
Community Directives to which they are subject::
Low Voltage 2014/35/EU
Electromagnetic Compatibility 2014/30/EU

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
7
3. PERFORMANCE TRAIT AND SKILL SPECIFICATIONS
◎Voltage：100~240V~ 50/60Hz.
◎Power：264W.
◎LED chip：10W，RGBW 4 in 1 LED chip.
◎LED QTY：18PCS.
◎LED life：50000H.
◎Lens degree：1.5°.
◎Beam angle：min.6°,max.60°.
◎Color: RGBW macro color system.
◎Strobe：1-30 times/ second electronic strobe and random strobe.
◎Dimmer：65536 class dimmer.
◎Pan/Tilt ：Pan ：540° times /2.0 seconds Tilt：180°/1.2 seconds.
◎Control Mode: DMX512, RDM, Stand-alone mode ,Voice Control
mode , Mater-Slave mode , Wireless DMX512.
◎Channel: Simple(11CH),Standard(17CH), Extended1(21CH),
Extended2(25CH)
◎Display Menu:
1. 2.4 inches TFT touch screen, Chinese and English two version
language.
2, Display board can record device’s using time , show device’s
temperature, channel data and software version .
3, Edit the procedure

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
8
◎Other feature :
1.Extend IP address function , each IP address maximum can set 64
ID
2.Support DMX signal priority identification, when lose the signal
it would be turn into Black , default scene , Automatic function
etc according to your set.
3.Remote control function: control the procedure, speed etc function
by the remote controller when the product under the condition
without signal.
4.Software upgrade : upgrade software by XRL cable.
◎Outlooking: adopt ABS anti-fire plastic.
◎Carton size : 412×287×525MM.
◎N.W.: 8.5KG G.W.: 11.1KG
◎Light size:322×242×336MM
◎
4. OPERATION PANEL

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
9
5. DIMENSIONAL DRAWINGS
6. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking
paths, seating areas, and away from areas were unauthorized personnel
might reach the fixture. Before mounting the fixture to any surface, make
sure that the installation area can hold a minimum point load of 10 times
the device's weight. Fixture installation must always be secured with a
secondary safety attachment, such as an appropriate safety cable. To
avoid injury, never stand directly below the device when mounting,
removing, or servicing the fixture.
Mounting points:
Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the
installation material being used, and periodic safety inspection of all

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
10
installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in
bodily injury. Be sure to complete all rigging and installation procedures
before connecting the main power cord to the appropriate wall outlet.
Mounting
Our company is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a flat level surface, etc. Be sure this
fixture is kept at least 0.5m (about 1.6feet) away from any flammable
materials (decoration etc.).
When clamp mounting; always use and install the supplied safety
cable as an added safety measure to prevent accidental damage in the
event of a clamp failure. See the image below.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
11
7. POWER SUPPLY AND SIGNAL CONNECTION
1. Power supply
Use the professional plug to connect the projector and main power
supply. Please pay attention to the voltage, frequency the same as the
mentioned on the projector. Suggest each light has separately switched of
the power supply so that could turn on or turn off each projector
desultorily.
2. Signal connection
Please use the round 3/5-pin XLR plugs &sockets offered by menu
facture to connect the first projector's output to the second projector'
input and connect the second projector's output to the third device's input.
And in the same way for the rest, eventually connect the last device's
output, all the devices are together as the following figure.
The devices’ control signal output or input by using the 3/5-pin XLR pug
and socket. If need to long then the communication cable, please make
sure the both side of 3/5-pin plug is one to one. (one to one, two to two,
three to three). Otherwise, the communication cable will be interrupted.
The communicate cable is 2-pin shielded cable 75Ω
Resistance with each core is at least a 0.5mm diameter. (Caution: All the
inside leading wire of 3/5-pin XLR plug couldn't touch each other or
plinth).
Recommend to use the DMX signal terminator for the installation to
avoid the electronic noise damage the digital control signal. Simply

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
12
speaking, DMX terminator is an XLR connector with a 120Ω 1/2w
resistor connected across pin 2 and 3.Which is then plugged into the
output socket on the last projector in the chain. Refer to the connection as
above:(Picture ).We suggest using the DMX signal distributor when the
distance of the lights over 15meter,In case of effect the light
communication because of the signal feeble.
3. Light power connection:
the items can't be more than 6pcs under series connection.
After doing the above operation and making sure all the devices had
been installed with natural operate, press the power switch to check
whether everything is working normally.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
13
8. DISPLAY MENU
ⅠMenu
ⅡMenu
Ⅲ Menu
Remark
SETTING
DMX Address
001-512
Fixture ID
000-064
Channel mode
Simple(11CH)
Standard(17CH）
Default
Extended1(21CH）
Extended2（25CH）
DMX input mode
Wired input
Default
Wireless input
Reset wireless
DMX function
Hold
Black
D.scene
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Program 8
Slave-Master
Slave mode
Master mode
Sound control
Close
Open
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
14
ⅠMenu
ⅡMenu
ⅢMenu
Remark
INFO
Fixture times
Power on time ****H
Lamp on time ****H
Fixture
temperatures
LAMP_TEM ***℃
RDM UID
3888:********
DMX live
1. Dimmer 0-255
2. Dimmer fine 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro colour 0-255
17.Pan 0-255
18.Pan fine 0-255
19.Tilt 0-255
20.Tilt fine 0-255
21.Lens Rota. 0-255
22.Rota.speed 0-255

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
15
ⅠMenu
ⅡMenu
ⅢMenu
Remark
INFO
DMX live
23.Fixture control 0-255
24.Calibration 0-255
25.Slave ID 0-255
Version info
LED_XY_SOFT:V*.**
LED_DPY_SOFT:V*.**
Exit
ⅠMenu
ⅡMenu
ⅢMenu
ⅣMenu
Remark
PERSON
Pan/Tilt
P/T swap
Close
Default
Open
Pan invert
Close
Default
Open
Tilt invert
Close
Default
Open
Exit
Reset
System reset
Exit
Quick
closedown
Open
Close
P/T angle
limit
Close
Open
Program
on/off
Close
Open
Set P/T
angle
Pan start
Pan end
Tilt start
Tilt end
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
16
ⅠMenu
ⅡMenu
ⅢMenu
ⅣMenu
Remark
PERSON
Display
Display
language
English(英文)
Default
Chinese（中文)
Display sleep
Light always
2 minutes
Default
4 minutes
6 minutes
Display
intensity
10-100
Display
rotation
Normal
Default
Rotate 180
TFT calibration
Exit
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
17
ⅠMenu
ⅡMenu
ⅢMenu
Remark
MANUAL
1. Dimmer 0-255
2. Dimmer fine 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro 0-255
17.Pan 0-255
18.Pan fine 0-255
19.Tilt 0-255
20.Tilt fine 0-255
21.Lens Rota. 0-255
22.Rota.SP 0-255
23.Fixture 0-255
24.CAL 0-255
25.Slave ID 0-255
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky.com.cn
www.lightsky-china.com
18
ⅠMenu
ⅡMenu
ⅢMenu
ⅣMenu
PROGRAM
Edit
program
Edit
program 1
Scene 0-100
1. Dimmer 0-255
2. Dimmer fine 0-255
3. Shutter 0-255
4. Red-1 0-255
5. Green-1 0-255
6. Blue-1 0-255
7. White-1 0-255
8. Red-2 0-255
9. Green-2 0-255
10.Blue-2 0-255
11.White-2 0-255
12.Red-3 0-255
13.Green-3 0-255
14.Blue-3 0-255
15.White-3 0-255
16.Macro 0-255
17.Pan 0-255
18.Pan fine 0-255
19.Tilt 0-255
20.Tilt fine 0-255
21.Lens Rota. 0-255
22.Rota.SP 0-255
23.Fixture 0-255
24.CAL 0-255
25.Slave ID 0-255
Save scene
Exit